EAST COAST Toulouse Dresser Grey User guide

Toulouse Dresser
Grey
Assembly and care
instructions

Hexagon key
A x 16
(long)
B x 13
(short)
C x 48
G x 27
(long)
I x 12
J x 6
D x 5
E x 5
F x 14
H x 28
(short)
IMPORTANT. RETAIN FOR FUTURE REFERENCE:
READ CAREFULLY
Hardware
Thank you for purchasing an East Coast product. It’s been carefully designed and constructed to oer
quality, safety and reliability for you and your baby.
If you have a query about this product or require replacement parts, please contact 01692 408802.
Your child’s safety is your responsibility. Keep children clear during assembly as the fittings pack contains
small parts which may present a choking hazard. Please read the instructions and warnings carefully before
use.
Lay out the parts on a soft level surface and compare to the parts checklist. Don’t throw away any
packaging until you’re sure that you have all the parts.
You will need the following tools to complete assembly:
Flat-headed screwdriver and cross-point screwdriver
2

Wooden Parts
Changer side 1
Changer divider 2
Changer divider 1
Changer front
Changer rear
Lower back panel
Dresser top
Twin drawer front
Single drawer front x 2
Front crossbar
Drawer side x 6 (L & R)
Drawer brace x 3
Drawer base x 3
Plain crossbar x 4
Side panel x 2 (L & R)
Upper back panel
Upper rear crossbar
Upper front crossbar
Changer side 2
Drawer back x 3
3

Upper front crossbar
NOTE: Take care to insert the dowels into the
correct holes as indicated. Repeat for the opposite
end of each crossbar. (Total 28 x part C)
Assembly 1
Assembly 2
Front crossbar
Plain Crossbar x 4
Upper front crossbar
Upper rear crossbar
Plain crossbar
Plain crossbar
Plain crossbar
Front crossbar
F
A
NOTE: Secure all Crossbars using
Parts A and F (1 each per Crossbar)
as shown.
Side panel
C x 14
Plain crossbar
Upper rear crossbar
4

Assembly 3
Assembly 4
D x 5
F
A
NOTE:
Secure Crossbars using Parts A and F
(1 each per Crossbar) as shown.
Side panel
Changer front
Changer divider 1
Changer side 2
5

Assembly 6
Assembly 5
C x 8
C x 8
Changer divider 1
Changer side 2
Changer side 1
Changer divider 2
B x 2
Changer side 2
Changer side 1
Dresser top
Changer divider 2
Changer divider 1
Assembly 7
E x 2
6

Assembly 9
Assembly 8
Changer front
E x 3
B x 5
Changer rear
7

NOTE: Ensure the
Dresser Top is
assembled as
shown.
Changer front
Front crossbar
Assembly 11
Assembly 10
C x 4
Dresser top
B x 3
B x 3
A x 2
8

Assembly 12
Upper Back Panel (Slot at top)
H x 14
Assembly 13
Assembly 14
G x 2
H x 14
Lower Back Panel
NOTE: Repeat for remaining drawers.
NOTE: Repeat for remaining drawers.
Twin drawer front
Drawer side
Drawer side
Drawer base
G x 2
9

Assembly 15
Assembly 16
Assembly 17
Drawer back
Drawer brace
G x 2
G x 3
I x 4
J x 2
NOTE: Repeat
for remaining
drawers.
NOTE: Repeat for
remaining drawers.
Twin drawer front
Single drawer front
Single drawer front
10

Assembly 18
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place the dresser against the wall where it is to be fitted. Remove the top drawer and mark the wall
through the slot in the Upper Back Panel.
2. Move the dresser away and using the long screw, washer and the appropriate wall fixing attach the
fabric strap to the marked position.
3. Replace the dresser and thread the fabric strap through the slot in the Upper Back Panel.
4. Attach the fabric strap to the Upper Rear Crossbar using the short screw and the washer.
5. Replace the top drawer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
Washer x 2
Screw (short)
Screw (long)
Plastic wall plug
(for brick and masonry wall use
only)
Fabric strap
1
2
4
The type of wall fixing you will require depends on the construction of the wall. See below for details. If
in doubt, seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away the
core structure.
Brick or masonry: Use the
wall plug, provided you are
sure that your wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.
11

EC_TDRG_300119
For customer care or enquiries:
Call: 01692 408802
Email: [e-mail]
East Coast Nursery Ltd. Robertson House, North Walsham,
Norfolk, NR28 0BX
eastcoastnursery.co.uk
Care and maintenance
In use
All assembly fittings should be tightened properly and should be checked regularly and re-tightened as
necessary. Take care when moving the furniture, as careless handling may cause damage.
Cleaning is simple; just wipe over with a damp cloth, and avoid using strong detergents or abrasives.
An occasional light application of a wax polish will help maintain the finish.
Warning: Do not leave your child unattended.
Ensure that all fittings are tightened properly. Loose screws could allow a child to trap a part of their
body or clothing, posing a strangulation risk.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Suitable for use with a flat changing mat up to 76 x 47 cm which does not compromise the eective
height of the changer barriers.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.