EAST COAST Monaco Manual

Monaco
Dresser

2
Important
Retain for future reference: Read carefully
Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation
of this product.
Your child’s safety is your responsibility. If you have a query with this product or require replacement
parts, please contact 01692 408802.
Lay out the parts on a soft level surface and compare to the part/fixing checklist on pages 2 and 3. Do
not discard any packaging until you are sure that you have all the parts.
Keep children clear during assembly as pack contains small parts which may present a choking hazard.
You will need the following tools to complete assembly:
Flat-headed screwdriver and Cross point screwdriver.
Hardware
G x 12
(25mm)
H x 12
I x 18
(38mm)
B x 12
A x 20
C x 24
E x 4
Ø 10mm
D x 28
Ø 8mm
F x 24
Hexagon Key x 1
J x 4
K x 4
L x 2

3
Wooden Parts
Changer Side x 2 (L & R)
Changer Back
Drawer Base x 3
Changer Front
Dresser Top
Front Upright x 2 (L & R)
Rear Upright x 2 (L & R)
Upper Front Crossbar
Plain Crossbar x 2
Lower Front Crossbar
Upper Rear Crossbar
Lower Rear Crossbar
Drawer Back x 3
Drawer Side x 6 (L & R)
Changer Base
Drawer Front x 3
Dresser Side x 2 (L & R)
Back Panel x 2
Lower Frame
Foot x 4
Panel Joiner Strip

4
Assembly 1
Assembly 2
NOTE:
Repeat for
opposite side.
Lower Frame
Lower Frame
Foot
Foot
Foot
Foot
A x 4
E x 2

5
Dresser Side
Assembly 3
Assembly 4
Dresser Side
A x 2
D x 4
A x 2
Lower Frame

6
Assembly 5
Dresser Top
Assembly 6
C x 4
F x 4

7
Assembly 8
Assembly 7
Upper Rear Crossbar
Lower Rear Crossbar
D x 2
D x 2
Upper Rear Crossbar
Rear Upright
Lower Rear Crossbar
A
B
NOTE: Rounded Corner
NOTE: Square Corner

8
Assembly 10
Assembly 9
Rear Upright
Back Panel
Back Panel
A
B
F x 8
Panel Joiner Strip

9
Assembly 11
Assembly 12
D x 6
C x 4
C x 4
NOTE: Gap between
metal drawer runner and frame edge
Assembled Rear panel from
Assembly 10
I x 3

10
Assembly 13
Assembly 14
D x 4
D x 4
A
B
NOTE: Square Corner
NOTE: Round Corner
Upper Front Crossbar
Plain Crossbar
Plain Crossbar
Lower Front Crossbar
Upper Front Crossbar
Plain Crossbar
Plain Crossbar
Lower Front Crossbar
Front Upright
Front Upright

11
Assembly 15
Assembly 16
F x 8
D x 6

12
Assembly 17
Assembly 18
C x 4
C x 4
Drawer Front
Drawer Side
Drawer Side
Drawer Base
NOTE: Gap this end
NOTE: Repeat for remaining two drawers
G x 4
I x 3

13
Assembly 19
H x 4
I x 4
Drawer Back
Assembly 20
NOTE: Ensure that inner drawer runner
is at forward edge before inserting the drawer.
Position the drawer mounted strip inside the
inner runner and holding the drawer level,
gently slide the drawer all the way into the
frame.
To open the drawer, push lightly on the pad on
the drawer front and allow the drawer to slide
out a little, then pull the rest of the way open.
NOTE: Repeat for remaining two drawers
NOTE: Repeat for remaining two drawers
To remove the drawer, locate the
plastic tabs on the drawer mounted
strips. Press gently down on one side
and lift the other whilst pulling the
drawer out.

14
Assembly 21
F x 4
Changer Front
Assembly 22
Changer Front
Changer Side
Changer Base
Changer Side
Changer Back
K x 4
C x 4
Assembly 23
J x 2
L
Assembled changer
NOTE:
DO NOT use the
changer unless it is
secured to the Dresser
unit with parts J and L

15
Assembly 24
The dresser is supplied with a fixing kit which will secure it and help to guard against accidental tipping.
WARNING : Installation only to be carried out by a competent person.
Check the suitability of the wall before fitting.
1. Place the dresser against the wall where it is to be fitted. Mark the wall at the centre of the top crossbar.
Move the dresser away.
2. Using the 25mm screw, washer and the appropriate wall fixing attach the fabric strap to the marked
position.
3. Replace the dresser and attach the strap to the centre of the upper rear crossbar using the 15mm screw and
the washer.
Before use, ensure that the strap is securely fixed to both the wall and the dresser.
Washer x 2
Screw (15mm)
Screw (25mm)
Plastic wall plug
(for brick and masonry wall use only)
Fabric strap
1
2
3
The type of wall fixing you will require depends on the construction of the wall. See below for details. If in doubt,
seek professional advice.
Wood: If fixing to wood make
sure that it isn’t chipboard as
screws can easily pull away
the core structure.
Brick or masonry: Use the
wall plug, provided you are
sure that your wall is sound.
Cavity wall: Special toggle
wall plugs needed.
Seek expert advice.

Care & Maintenance
Your furniture may be cleaned by wiping with a damp cloth and drying with a soft clean cloth.
Do not use abrasives, bleach, alcohol or ammonia-based household polishes.
Take care when handling or moving the furniture. Careless handling may cause damage.
Regularly check that all fixings are tightened and that there are no broken or damaged parts.
In use
Warning: Do not leave your child unattended.
All assembly fixings should always be tightened properly. Care should be taken that no screws are
loose because a child could trap parts of their body, or clothing (e.g. strings, necklaces, ribbons,
dummies, etc.) which could pose a risk of strangulation.
Be aware of the risks of open fires and other such sources of strong heat, such as electric bar fires, gas
fires, etc. in the near vicinity of the dresser.
Do not use as a changing unit when the Changer Cover is fitted.
Suitable for use with a flat changing mat 76 x 47 cm which does not compromise the effective height of
the changer barriers.
The changing area is suitable for use up to 12 months old or 11kg in weight.
Do not use the dresser if any of the parts are broken, torn or missing.
Any additional or replacement parts can only be obtained from the manufacturer or the distributor.
Customer Care line for this Product 01692 408802
7848-01
East Coast Nursery Ltd. Robertson House, North Walsham, Norfolk, NR28 0BX
www.eastcoastnursery.co.uk