Sauder Original Cottage 414183 User manual

PLEASE CONTACT US
BEFORE RETURNING
YOUR UNIT TO THE STORE
1-800-523-3987
www.sauder.com
Made in the USA
Archbold, OH
NOTE: THIS INSTRUCTION BOOKLET CONTAINS
IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Lot #: 349642 02 / 25 / 13
Date Purchased: ____________________
English.................... Page 1-12
Français...............Pages 13-14
Espanol.............Páginas 15-16
414183
Bookcase
Original Cottage Collection

ASSEMBLY TOOLS REQUIRED
Hammer
No. 2 Phillips Screwdriver
Tip Shown Actual Size
ADULT ASSEMBLY REQUIRED
TABLE OF CONTENTS
Part Identification.......................3
Hardware Identification .............4
Assembly Steps....................5-12
Français..............................13-14
Espanol...............................15-16
Safety .................................17-18
Warranty...................................19
Page 2 www.sauder.com/services 414183

PART IDENTIFICATION: While not all parts are labeled, some of the parts will have a label or an inked
letter on the edge to help distinguish similar parts from each other. Use this PART IDENTIFICATION to help
identify similar parts.
A END 2
B TOP 1
C BOTTOM 1
D BACK 1
E ADJUSTABLE SHELF 2
F RIGHT FRONT/LEFT REAR LEG 2
G LEFT FRONT/RIGHT REAR LEG 2
H SKIRT 1
I TOP MOLDING 1
Page 3
www.sauder.com/services414183
A
B
C
DE
F
G
H
I
A
E
F
G

HARDWARE IDENTIFICATION
Screws are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com/services 414183
SAFETY BRACKET - 1
1G ANGLE BRACKET - 3 27G19G LARGE METAL BRACKET - 3
BLACK 9/16" LARGE HEAD SCREW - 13
1S BLACK 1-7/8" PAN HEAD SCREW - 1 16S
CAM SCREW - 16
8F
HIDDEN CAM - 24
1F CAM DOWEL - 8 2F
RUBBER SLEEVE - 8
2R
METAL PIN - 8
1R
NAIL - 36
1N CAM COVER - 16 32P

Look for this icon. It means a video
assembly tip is available at:
www.sauder.com/services/tips
1
1
S
t
e
p
Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
Push twenty-four HIDDEN CAMS (1F) into the ENDS (A) and BOTTOM (C). Then, insert the metal end of eight CAM
DOWELS (2F) into the indicated HIDDEN CAMS. Do not insert CAM DOWELS into the long edges of the ENDS (A).
Page 5
www.sauder.com/services414183
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
1F
Arrow
1F
Arrow
(8 used)
(24 used) 1F
2F
2F
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Arrow
Do not insert
CAM DOWELS
into these edges.
A
C
A

Page 6 www.sauder.com/services 414183
2
2
S
t
e
p
Turn sixteen CAM SCREWS (8F) into the LEGS (F and G).
8F
(16 used)
F
G
F
G

Page 7
www.sauder.com/services414183
3
3
S
t
e
p
A
A
Fasten the LEGS (F and G) to the ENDS (A). Tighten sixteen HIDDEN CAMS.
Surface
with holes Surface
with holes
Edge with
CAM DOWELS
These ends
should be even.
F
G
F
G
These ends
should be even.

Page 8 www.sauder.com/services 414183
4
4
S
t
e
p
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
Fasten the ENDS (A) to the BOTTOM (C). Tighten four HIDDEN CAMS.
Maximum
210 degrees
Minimum
190 degrees
Arrow
A
AC
F
G
These holes
must be here.
Surface
with holes
Finished edge

Page 9
www.sauder.com/services414183
5
5
S
t
e
p
A
A
B
Fasten the TOP (B) to the ENDS (A). Tighten four HIDDEN CAMS.
Maximum
210 degrees
Minimum
190 degrees
Arrow
These holes
must be here.
Surface with holes

Page 10 www.sauder.com/services 414183
6
6
S
t
e
p
B
C
H
Fasten three ANGLE BRACKETS (27G) to the TOP (B). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).
Fasten the TOP MOLDING (I) to the ANGLE BRACKETS (27G) on the TOP (B). Use three BLACK 9/16" LARGE HEAD
SCREWS (1S).
NOTE: There are no pre-drilled holes in the TOP MOLDING. The SCREWS will tighten into the groove.
Fasten three LARGE METAL BRACKETS (19G) to the BOTTOM (C). Use three BLACK 9/16" LARGE HEAD SCREWS (1S).
Fasten the SKIRT (H) to the LARGE METAL BRACKETS (19G) on the BOTTOM (C). Use three BLACK 9/16" LARGE HEAD
SCREWS (1S).
NOTE: There are no pre-drilled holes in the SKIRT. The SCREWS will tighten into the groove.
BLACK 9/16" LARGE HEAD SCREW
(12 used in this step)
1S
27G
19G
I
Use the
center hole.