edenox MBM-311 User manual

Installation, operation and maintenance
manual
Bain Marie Units
MBM-311, MBMR-311, SBM-311, SBMR-311
MBM-411, MBMR-411, SBM-411, SBMR-411

2
Installation, operation and maintenance manual
BAIN MARIE UNITS
MBM-311, MBMR-311, SBM-311, SBMR-311
MBM-411, MBMR-411, SBM-411, SBMR-411
WARRANTY
Edenox assumes liability for manufacturing defects only. This warranty
excludes, therefore, any liability for the incorrect handling or operation of the
equipment by the customer or user. This warranty will remain in effect for a period of
six months and will cover components with manufacturing defects only. Labour and
transport costs are the exclusive responsibility of the customer in all cases. Edesa
does not accept any responsibility for defects attributable to transport unless claims
are made within 24 hours of receipt of the goods.
SPECIFICATIONS
Bain Marie meal distribution units have been designed to maintain food
at a predetermined, thermostat-adjusted temperature.
• Temperature range between +30ºC and +90ºC.
• Deep-drawn Bain Marie well with rounded corners.
• Well with capacity for 3 200mm-deep Gastronorm 1/1 pans in the 311 models
and 4 200mm-deep 1/1 pans in the 411 models.
• Gastronorm pans are not included.
• On top, Bain Marie with water.
• The temperature of the Bain Marie is thermostat-controlled. In models fitted with
a cupboard, the temperature of the Bain Marie and the cupboard is regulated
separately with two different thermostats.
• In models fitted with a cupboard, this is heated with forced air.
• Equipped with an analogue thermometer.
• Unit “on” indicator pilot light.
• Taps included for water inlet and drainage.
• Sturdy legs with height-adjustable feet.
• Sliding doors.
• Double-wall doors with ecological polyurethane insulation with a density of 40
kg.
• Interior and exterior in 18/10 stainless steel.
• Important: The well must be filled with water before the Bain Marie is
Switched-on.
MBM-311, SBM-311
Resistencias: 3 de 700W
Consumo: 9.5A
MBMR-311, SBMR-311
Resistencias (cuba): 3 de 700W
Resistencias (reserva): 1 de 1400W
Consumo: 16A
MBM-411, SBM-411
Resistencias: 3 de 700W
Consumo: 9.5A
MBMR-411, SBMR-411
Resistencias (cuba): 3 de 700W
Resistencias (reserva): 1 de 1400W
Consumo: 15.9A
•Installation
•
•Place the unit on a flat surface and make sure that it is correctly levelled.
•Connect the unit to the mains power supply (230V II 50 – 60 Hz or 230V and
400V III 50 – 60 Hz according to model). 411 models leave the factory ready for
operating at 400V. Should it be necessary to convert it to 230V, a bag with all the
elements required to make the conversion is included.
• The unit must be correctly earthed
(See diagrams)

3
OPERATION
Turn on the unit at the general on/off switch.
Select the working temperature by turning the thermostat control to the desired
setting.
The pilot light located next to the thermostat turns on when the heating elements
are in operation.
For optimum operation it is recommended to turn on the unit and allow it to heat up
to the required temperature before introducing the product (with the doors closed in
models with a lower hot cupboard).
Never obstruct the hot air vents located inside the lower hot cupboard, opposite
the fan.
SAFETY PRECAUTIONS
Warning: In view of the fact that this unit is designed for heating food, the well
and the inside of units fitted with a cupboard are extremely hot. Avoid direct
contact and take all the required safety precautions.
While work is being done on the heating system, the unit must be disconnected
from the mains power supply
Take precautions when removing food from inside the chamber, as the temperature
inside the unit may be very high..
INSTALLATION DIAGRAMS
FOR CONNECTING TO MAINS
1. Remove the Phillips screws and extract the front with the controls as indicated.
2. The inlet for connecting the mains cable is located at the bottom.
ACCESS TO ELECTRICAL INSTALLATIONS
1. Disconnect the unit from the mains.
2. The inlet for connecting the mains cable is located at the bottom.
3. In order to access the fan and the heating elements terminals, remove the
hexagonal M4 bolts with a wrench and slide open the side panel.
4. In order to access the well heating elements, remove the A bolts and remove the
panel.

4

5

6

7
DECLARACION DE CONFORMIDAD
DECLARATION OF CONFORMITY
Edenox
Pol. Ind. Can Milans - C/ Can Milans, 5
08110 Montcada i Reixac (Barcelona) Spain
Declara bajo su responsabilidad que los siguientes productos:
Declares under sole responsibility that the following products:
MESAS BAÑOMARIA / BAIN MARIE TABLES
Series / Models:
MBM-311/411 MBMR-311/411 SBM-311/411 SBMR-311/411
Son conformes con las siguientes directivas europeas:
Are in compliance with the following european directives:
2006/95/EC :
Directiva de Baja Tensión / Low Voltage Directive
2004/108/EC :
Directiva de Compatibilidad Electromagnética / EMC Directive
2011/65/EU : RoHS2
Para lo cual se han seguido las normas / For what have been followed the standards:
EN 60335-1:2002 + A15 :2011: Household and similar electrical
appliances. Security Part. 1: General requirements.
UNE-EN 60335-2-50 :2003 + A1: 2009: Particular requirements for electric
bain maries for collective use.
Montcada i Reixac
Agosto 2015
Lluis Bertomeu
Brand Manager