ekwb EK-FB ASUS ROG R6E Monoblock User manual

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 4.0. Published on February 1st 2018
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no
liability whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual thoroughly before beginning with the installation process!
2. Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and/or motherboard’s circuit board (PCB).
3. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
4. The use of quality, market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of ASUS ROG Rampage VI Extreme motherboard
BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws.
STEP 1: PREPARING YOUR MOTHERBOARD
STEP 2: PREPARING YOUR MOTHERBOARD
REMOVING STOCK COOLER. Remove all encircled screws. There are 2 screws on
the right back side of the motherboard that need to be removed in order to remove
I/O plastic cover and 4 screws for the factory installed MOSFET heat pipe cooling
solution. Please store away the factory backplate as it will be reused.
1. APPLYING THERMAL COMPOUND. Apply thermal compound on CPU heat
spreader (IHS) - see sample photo on right with enclosed EK-TIM Ectotherm thermal
grease.
The quantity of about two rice grains is just about right. There is no need to cover
the whole IHS. Applying too much thermal grease will have negative impact on the
cooling performance!
2. CUTTING THERMAL PADS. Your block comes with thermal pads which needs to be trimmed in order to fit the voltage regulation area (MOSFET) on the motherboard’s
circuit board. WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED.
Replacement thermal pads @ EKWB web shop:
Thermal PAD G 1mm - (120x24mm) [EAN: 3830046996770]
Thermal PAD F 2mm - (120x16mm) [EAN: 3830046996756]
Installation manual for EK-FB ASUS ROG R6E Monoblock water block
Mosfets
CPU socket
X299 PCH
(SB)
1. Thermal pad G–1.0mm
(for mosfets and inductor coils):
2. Thermal pad F–2.0mm
(for AQUANTIA Ethernet controller):

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Revision 4.0. Published on February 1st 2018
STEP 3.1: PLACING THE HEATSINK ON TO MOTHERBOARD
(only for RAMPAGE)
PLACING THE HEATSING ON THE MOTHERBOARD AQUANTIA Ethernet controller.
Place the heatsink on to the motherboard and secure it using two M2,5x5 AX1
screws with M2.5 PVC washers. Then you can reinstall plastic factory I/O cover.
STEP 3.2: PLACING THE BLOCK ON TO MOTHERBOARD
STEP 4: ATTACHING BLOCK ON TO THE MOTHERBOARD
PLACING THE BLOCK ON THE MOTHERBOARD. Place the EK-FB ASUS ROG R6E
Monoblock series water block gently to the motherboard or vice versa (as shown on
photo below). Make sure that mounting holes are aligned. Place it on factory installed
washers on the motherboard (MOSFET area).
Prior to fastening the screws please make sure the mounting holes on the
motherboard’s circuit board are aligned with the water block.
A) Mosfet part: Use two M2,5x7 AX1 screws with original backplate. Tighten the
screws evenly. Do not use excessive force when tightening the screws!
B) CPU part: Use four thumb nuts with screws and washers. Tighten
the thumb nuts.
Use the enclosed screws and washers as shown in picture below:
STEP 5: CONNECTING THE LED STRIP (optional)
CONNECTING THE RGB
Plug the 4-pin connector from Monoblock
RGB LED strip to the motherboard.
Please ensure that the arrow indicated on
the connector is plugged into the 12V line
as indicated on your motherboard. failure
to do so will damage your motherboard
or LED strip.
CONNECTING THE D-RGB
Plug the 4-pin connector from Monoblock
D-RGB LED strip to the ADD HEADER on
the motherboard. Please ensure that the
arrow indicated on the connector is
plugged into the +5V line as indicated on
your motherboard. Failure to do so will
damage your motherboard or LED strip.
*D-RGB header is available only on
ASUS Rampage VI Extreme
motherboard
For the EK-FB ASUS ROG R6E Monoblock series water block to operate properly the
G1/4 port nearest to the right edge of the water block MUST BE USED AS THE
INLET PORT. EK recommends the use of EK-ACF fittings. When using fittings other
than EK-ACF series please use hose clamps or appropriate substitute to secure the
tubing to the barb. The use of biocide containing and corrosion inhibiting coolant is
always recommended for any liquid cooling system.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver Allen key
M3 PVC Washer
Factory backplate
M2.5x7 screws
M3 thumb nut
3. PLACING THERMAL PADS ON MOTHERBOARD. Place thermal pads on
PCB as shown on the picture. PLEASE REMOVE THE PROTECTIVE FOIL
FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION!
Place 1mm thermal pads
in larger strips over both
marked area and make
sure all mosfet chips and
inductor coils are covered.
Place 2mm thermal pad
on AQUANTIA Ethernet
controller.
M2.5x5 screws
M2.5 PVC
Washer
Tubing
IMPORTANT: USE
THIS OPENING AS
AN INLET PORT!