Elite Screens Elite Home 2 Series User manual

1
Rev.060616-DR www.elitescreens.com
Electric Motorized Projection Screen
Home 2 Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedure below.
Caution: The Screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop
in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or
modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your
warranty. For more information, please contact our Technical Support Department at [e-mail].
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not place any heavy objects over the power cord.
Position the power cord properly to avoid creating a trip obstacle.
To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the power
cord.
The internal & external parts of this unit are not end user serviceable. Do not attempt to disassemble
this unit by yourself. No one except authorized technicians can open and make repairs to this unit.
Make sure the power source that this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to
avoid over heat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind thunder or lightning.
Avoid direct sun light, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
To avoid possible injury and/or an electric shock, do not attempt to use this screen if there is obvious
damage or if there are any evident broken parts.

2
Rev.060616-DR www.elitescreens.com
WARNING
Due to various installation environments, the instructions provided in this user’s guide are for reference
only. Please consult a professional installation company for further installation and safety advice. The
installer must insure that proper mounting hardware is used to provide adequate strength suitable for the
installation. Elite Screens is not liable for any faulty installations.
The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles
such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the
viewing surface will not cause the casing to become loose or fall. The installer must insure that the fasteners used
are of adequate strength and suitable for the installation location.

3
Rev.060616-DR www.elitescreens.com
Sensor
3-way Wall box switch
Sensor
Home 2 Series | Controls and Accessories
A. IR Remote
B. RF Remote
C. Wall switch control box
D. 5-12 volt trigger cable
E. IR extended “eye” receiver
F. Wireless 5-12v (3.5 mm)
mono trigger cable
G. AAA batteries
H. Bubble leveler
Screen Operation
Electric Current: Depending upon region, your Elite Screen will operate on 100v, 110v, or 220v voltage.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Home 2
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line
of sight contact with a beam range of 30 feet. Aim the IR remote at the
circular window located on the left side of the screen.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs
directly into the control box’s RJ45 port to present a low profile line-of-
sight control option for your IR remote control even in a recessed ceiling
installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a
direct line of sight with a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall
mount switch with an up/stop/down button and plugs directly into the
control box’s RJ45 port.
Fig.3
UP
STOP
DOWN
Fig.1
IR/RF remote
IR “eye” receiver
Fig.2

4
Rev.060616-DR www.elitescreens.com
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a
handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency technology
can be programmed to send a wireless signal to synchronize its drop/rise with the projector’s power cycle.
Here’s how to set up your Wireless 5-12 volt trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to
control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-30seconds
for full off and on cycle each time)
Hardware Parts List
Please make sure all items listed below are included before proceeding with the installation.
Hardware Parts List
QTY
A. Screw & Dry Wall Anchor
2 EA.
B. Bolt
2 EA.
C. Masonry Screw & Anchor
2 EA.
D. Extruded Hanging Bracket
2 or
3 EA.
A
B
D
120” & above x 3 brackets
DC 5-12V out
The back of the
projector
Wireless 5-12V trigger cable
UP
Stop
Down
Fig 5
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V
trigger input allows your screen to synchronize its drop &
rise with the projector’s power cycle. The screen deploys
when the projector powers up and will retract when the
projector powers down. The 5-12 volt RJ45 cable connects
to your projector’s trigger output via a separate cable that
may or may not be provided by the manufacturer of the
projector. The trigger feature will not work without an
output cable from the projector, but it can be tested by
connecting the Red (+) and Green (-) cable to a 9-volt
battery.
Fig.4
C
3-prong power cable
Red: DC 12 +
Green: 0 V -
RJ-45 input connection for
5/12 volt trigger inside of case

5
Rev.060616-DR www.elitescreens.com
Installation Instructions
Please consult a professional installer. Elite Screens is not liable for any faulty installations.
1. Insert each Bolt (B) through the right & left slide channel located on the top of the screen’s case.
2. Slide the Extruded Hanging Bracket (D) through the rail located below the slide channel until it meets with
the top of the Bolt (B) and slightly secure the lug-nuts located on the top & bottom of the bolt to attach the
bracket.
3. Mark the installation location to drill your hole. Insert the proper screw and secure the bolts to the bracket.
4. Example of the Home 2 installed to a wall, ceiling and enclosed.
C
Top hole for ceiling installation
Back hole for wall installation
Flush mount
to wall
Flush mount
to ceiling
Enclosed
installation
*Allow 2” of spacing
between the front and
back of the screen casing.

6
Rev.060616-DR www.elitescreens.com
Trouble Shooting
For additional information, please contact Elite Screens at [e-mail]
1. If your screen does not move, please check the power supply. The screen will understandably not move
without power.
2. Make sure the power cord is firmly plugged to the power outlet.
3. Make sure that all cable connections are secure.
4. If the screen works well with the line switch but not with the remote control, please make sure the remote
controls have fresh batteries. Change the batteries every 6 months to ensure proper operation of the
remotes.
FAQ’s
1. Q: Why does my screen no longer function?
A: Make sure your wall plug has power and that the screen is properly plugged. The fuse on the screen will
also need to be checked. Please contact [e-mail] for the location. The tubular motor
in this screen is equipped with a thermal relay. This feature will automatically shut off the screen in the
event of the motor becoming too hot. This will prevent the motor from overheating. If you should
experience this, please let the screen’s temperature decrease for 10-15 min. before usage.
2. Q: How is the screen material cleaned?
A: The screen material can be cleaned with mild soap and water.
3. Q: What type of batteries do the remote controls require?
A: The IR and RF remote controls use AAA alkaline batteries.
4. Q: Can you manually pull down the screen?
A: No, manually pulling down the screen will damage the electronic motor rolling system and void your
warranty.
5. Q: How could I setup my Screens IR receiver to work with my learning remote control system
Do you have any IR codes I can use to achieve this?
A: Our IR remote controls have been evaluated and entered in to the databases of some Universal remote
control manufacturers. Please contact the manufacturer of your remote to inquire about your remotes
ability to function with ours. If they have not evaluated our remote control then the following list of Binary
codes will be used for most remote setups.
For Spectrum, VMAX2 (Plus), Home2 and CineTension 2 Series
Up: 1111 0000 0001
Stop: 1111 0000 0010
Down: 1111 0000 0100
6. Q: What is the gain on the matte white screen material?
A: The matte white material has a gain of 1.1. For detailed information, please visit
www.elitescreens.com/home2
For local Elite Screens contact or Technical Support, please visit
www.elitescreens.com