Elko SmartSensor Climate Wireless User manual

SmartSensor Climate Wireless
Device User Guide
Commissioning instructions for the ELKO Smart system, devices and app.
02/2023
www.elko.no

Legal Information
The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in
this guide are the property of ELKO AS or its subsidiaries. All other brands may be
trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
ELKO.
ELKO does not grant any right or license for commercial use of the guide or its
content, except for a non-exclusive and personal license to consult it on an "as
is" basis. ELKO products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
ELKO and its subsidiaries for any errors or omissions in the informational content of
this material or consequences arising out of or resulting from the use of the
information contained herein.

Table of Contents
Safety information.......................................................................................4
SmartSensor Climate Wireless.................................................................5
For your safety ...........................................................................................5
About the device.........................................................................................5
Installing the device ....................................................................................6
Pairing the device .......................................................................................6
Pairing device manually.........................................................................6
Pairing device with auto scan.................................................................9
Configuring the device ..............................................................................10
Changing the device icon ....................................................................10
Renaming the device .......................................................................... 11
Changing the device location ............................................................... 11
Removing the device ................................................................................12
Resetting the device .................................................................................13
Using the device.......................................................................................14
Checking the device history .................................................................14
Creating an automation .......................................................................15
Replacing the batteries .............................................................................19
LED indications ........................................................................................20
Troubleshooting .......................................................................................20
Technical Data .........................................................................................21
DUG_Sensor Climate_ELKO-00 3

Safety information
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it. The
following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates
that an electrical hazard exists which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
4 DUG_Sensor Climate_ELKO-00

SmartSensor Climate Wireless
SmartSensor Climate Wireless
EKO07219
For your safety
NOTICE
EQUIPMENT DAMAGE
Do not install the sensor in a place where there is strong sunlight or wind (for
example, close to the ventilation).
Failure to follow these instructions can result in equipment damage.
About the device
The SmartSensor Climate Wireless (hereinafter referred to as Temperature/
Humidity sensor) combines two sensors in one unit. The sensor measures
temperature and humidity in the environment where the sensor is installed. When
the sensor is connected to the ELKO SmartHUB, it reports the temperature and
humidity data to the ELKO SmartHUB.
The sensor triggers other ELKO devices (such as turning on an air conditioner if
the temperature is high or turning on an exhaust fan if the humidity is high)
through automation.
Operating elements
A. Status LED
B. Function key
AB
DUG_Sensor Climate_ELKO-00 5

SmartSensor Climate Wireless
Installing the device
Refer to the installation instruction supplied with this product.
See SmartSensor Climate Wireless.
Pairing the device
Using the ELKO Smart app, pair your device with the ELKO SmartHUB to access
and control the device. You can either add the device manually or do an auto-scan
to pair it.
Pairing device manually
To pair the device manually:
1. On Home page, tap +.
2. Tap , select the required ELKO SmartHUB on the slide-up menu.
3. Select an option to add the device (A):
–Add Device with Install Code
–Add Device without Install Code
Add Device
Install Code is Recommended
Add Device without Install Code
A
TIP: It is highly recommended to add the device with install code.
6 DUG_Sensor Climate_ELKO-00

SmartSensor Climate Wireless
4. To pair the device with an install code, tap Add Device with Install Code to
display the slide-up menu. Select any one of the options (B):
–Scan Install Code - you can scan the device for the install code.
–Enter Install Code Manually - you can manually enter the install code
from the device.
After adding the device with install Code, proceed to Step 6.
Add Device
Install Code is Recommended
Add Device without Install Code
Add Device
Install Code is Recommended
B
5. To pair the device without install code, tap Add Device without Install Code.
6. On the rear side of the sensor, short press the function key 3 times (< 0,5 s).
3× < 0,5 s
↓
The LED blinks orange.
DUG_Sensor Climate_ELKO-00 7

SmartSensor Climate Wireless
7. In the app, select Confirm LED is flashing orange and tap Start
configuration (C).
How to pair device
Short-press function key 3 times.
3
Cancel
C
The app displays the progress of connecting the device.
8. After a few seconds, a solid green LED indicates that the sensor is
successfully paired.
…
9. Tap Done when the pairing is successful..
8 DUG_Sensor Climate_ELKO-00

SmartSensor Climate Wireless
Pairing device with auto scan
Pairing the device with auto scan automatically discovers the device when the
corresponding device is powered on.
1. On the Home page, tap +.
2. Tap Auto scan > Confirm.
3. Enable permissions to Access location and Wi-Fi for scanning device and
tap Start scanning.
NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.
4. Tap Select hub and select the ELKO SmartHUB from the slide-up menu.
5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few
seconds until the device search is complete.
The LED blinks orange.
TIP: If you want to pair multiple devices at once, perform step 5 on each
device and wait for a few seconds for them to be detected.
6. Tap Next (A) and select Temperature Humidity Sensor.
Temperature
Humidity Sensor
Auto Scan
Available devices found
Next A
7. Once the device is added successfully, tap Done.
DUG_Sensor Climate_ELKO-00 9

SmartSensor Climate Wireless
Configuring the device
Changing the device icon
You can change the device icon using the ELKO Smart app.
1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device
icon:
–Take photo - allows you to click a photo from the mobile camera.
–Select from Icon Library - allows you to select an icon from the app
library.
–Select from Album - allows you to select a photo from the mobile gallery.
10 DUG_Sensor Climate_ELKO-00