Elo Touch Solutions ET3201L User manual

USER MANUAL
Elo Touch Solutions
ET3201L 32” Interactive Digital Signage Touchmonitor
ET4201L 42” Interactive Digital Signage Touchmonitor
ET5501L 55” Interactive Digital Signage Touchmonitor
ET5501LT 55” Interactive Digital Signage Touchmonitor
ET7001L 70” Interactive Digital Signage Touchmonitor
ET7001LT 70” Interactive Digital Signage Touchmonitor
SW601990 Rev L

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 2 of 37
Copyright © 2015 Elo Touch Solutions, Inc. All Rights Reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, including, but not limited to, electronic,
magnetic, optical, chemical, manual, or otherwise without prior written permission of Elo Touch Solutions, Inc.
Disclaimer
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Afffiliates
(collectively "Elo") makes no representations or warranties with respect to the contents herein, and specifically
disclaims any implied warranties of merchantability or fitness for a particular purpose. Elo reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of Elo to
notify any person of such revisions or changes.
Trademark Acknowledgments
AccuTouch, CarrollTouch, Elo, Elo (logo), Elo Touch, Elo Touch Solutions, Elo TouchSystems, IntelliTouch, iTouch,
SecureTouch, TouchTools and VuPoint are trademarks of Elo and its Affiliates. Windows is a trademark of Microsoft
Corporation.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 3 of 37
Table of Contents
Chapter 1 – Introduction........................................................................... 4
Chapter 2 – Unpacking.............................................................................. 5
Chapter 3 – Touchmonitor Installation................................................ 6
Chapter 4 – Mounting................................................................................ 9
Chapter 5 – Operation............................................................................... 13
Chapter 6 – Technical Support............................................................... 29
Chapter 7 – Safety & Maintenance........................................................ 30
Chapter 8 – Regulatory Information..................................................... 32
Chapter 9 – Warranty Information......................................................... 36

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 4 of 37
Chapter 1: Introduction
Product Description
Your new Interactive Digital Signage (IDS) touchmonitor combines Elo Touch Solutions reliable
performance with the latest developments in touchscreen technology and display design. This
combination of features creates a natural flow of information between a user and the
touchmonitor.
This touchmonitor incorporates a 24-bit color, active matrix thin-film-transistor, and digital
signage LCD panel to provide superior display performance. Its Full HD resolution of
1920x1080 is suitable for displaying graphics and images. Other features that enhance this
LCD monitor’s performance are Plug & Play compatibility, built-in speakers and headphone
output capability, a remote for on screen display (OSD) controls, and a family of IDS computer
modules.
The computer modules are designed to slide into a bay on the rear of the monitor. The
monitors form factor will not be affected and extra cabling is not required. Your IDS
touchmonitor will turn into an IDS All-in-One touchcomputer.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user manual to
maximize the life of your unit and prevent risks to user safety. See Chapter 8 for more
information on touchmonitor safety.
For your health and safety, it is strongly recommended that at least two people (four for the
ET7001L/ET7001LT) handle, lift, and/or move these touchmonitors.
This manual contains information that is important for the proper setup and maintenance of the
IDS and optional computer module. Before setting up and powering on your new touchmonitor
and computer module, read through this manual, especially the Installation, Mounting, and
Operation chapters.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 5 of 37
Chapter 2: Unpacking
Unpacking the Interactive Digital Signage Touchmonitor
To unpack the IDS, follow these steps:
1. The carton should be oriented in the manner according to its labeling. The hinged plastic
locks should be at the ‘bottom’.
2. Open and remove all 4 hinged plastic locks. There are 6 hinged plastic locks for the 7001L
unit.
3. Once the locks are removed, lift the cartons top lid off the bottom frame.
4. With the top lid removed, you now have access to the IDS touchmonitor and the included
accessories.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 6 of 37
Chapter 3: IDS Touchmonitor Installation
Connector Panel & Interfaces
Note: For your health and safety, it is strongly recommended that at
least two people (four for the ET7001L/ET7001LT) handle, lift, or move
these Touchmonitors. Elo recommends safe lifting techniques as
described in OSHA/NIOSH Guidelines.
Check that the following items are present and in good condition:
IDS touchmonitor
User Manual CD
oNot included in all models. Latest version of user guide is available at www.elotouch.com
Quick Install Guide
OSD Remote connected to the monitor
Cables
oHDMI, USB, North America power, Europe/Korea power, U.K. power, Argentina power,
Taiwan power, China power, Korea power, Japan power, & Japan 3pin-2pin adapter and
VGA cable for the Y-Cable (7001LT/5501LT).
The Y-Cable is used to send MDC to the monitor. For more information about
MDC commands, see page 20.
Remove the cable cover on the bottom rear (when viewed in landscape orientation) to access
the touchmonitors connector panel.
Pictures of the connector panel and interfaces. The OSD connection is in red.
3201L/4201L/5501L/5501LT/7001L/ET7001LT
Images of monitor back I/O ports with OSD remote

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 7 of 37
IDS Touchmonitor Connections to an External Computer
1. Connect the HDMI cable between the monitor and the video source.
2. Connect the USB touch cable between the monitor and the PC.
3. Select the correct power cable for your region. Connect it between the AC power source
and the touchmonitors POWER IN connector.
4. The touchmonitor ships in an ON state. Use the remote OSD to access the On Screen
Display Menu.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 8 of 37
Installing the IDS Touchscreen Technology Software Drivers
The Elo touch driver and the Elo Computer Module driver packs are available with the CD that
ships with the touchmonitor.
Visit the Elo Touch Solutions website www.elotouch.com for:
Updates to the Elo touch driver
Additional touch driver information
Detailed touch driver installation guides
Touch drivers for other operating systems
IntelliTouch Plus units are HID compatible, but will require the Elo driver if touch calibration is
required.
Optical units and Infrared are HID compatible and do not require an Elo touch driver. If an Elo
touch driver has previously been installed on the host computer, remove this driver by opening
Control Panel and selecting to remove the driver completely.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 9 of 37
Chapter 4: Mounting
Note: For your health and safety, it is strongly recommended that at
least two people (four are recommended for the ET7001L/ET7001LT)
handle, lift, or move these touchmonitors.
Note: Do NOT lay the display face-down as this can cause damage to
the monitor.
General Mounting Information
The following three mounting orientations are supported: Landscape, portrait and table-top
mode. For optimal touch performance, ensure that the monitor is supported fully and is as
flat as possible.
Portrait Mode
When rotating the monitor to portrait mode, ensure that the Elo logo appears in the same
location as the pictures below.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 10 of 37
Landscape
When rotating the monitor to landscape mode, ensure that the Elo logo appears in the same
location as the pictures below
Table Top –Refer to the Temperature Control section for table top mode requirements.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 11 of 37
Rear VESA Mount
For the 32” and 42” models:
A four-hole, 400x400mm mounting pattern is provided on the rear of the monitor.
The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 400,400,6MM
For the 55” models:
A four-hole, 600x600mm mounting pattern is provided on the rear of the monitor.
The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 600,600,6MM
For the 70” models:
A four-hole, 400x400mm mounting pattern is provided on the rear of the monitor.
The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 400,400,8MM
For the 7001LT” models:
A four-hole, 600x600mm mounting pattern is provided on the rear of the monitor.
The VESA FDMI-compliant mounting is coded: VESA MOUNT PER MIS-F, 600,600,8MM
Refer to www.elotouch.com for dimensional drawings.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 12 of 37
Optional Stand (for 3201L and 4201L Only) Elo PN: E455084
Optional Wall Mounts Kits (detailed information available on the MS drawing for each size):
Consult the wall mount user guide for detailed information located under the Support tab on each
IDS touchmonitor size.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 13 of 37
Chapter 5: Operation
Power
To turn the touchmonitor on or off, press the touchmonitor power button once. If a computer
module is installed, then the computer module will also turn on with the monitor.
To abruptly power off the computer module and touchmonitor, press and hold the touchmonitor
power button until the computer shuts off.
To gracefully shut down the computer module, follow the computer modules operating systems
normal power off procedure.
A Power Status LED is provided on the OSD Remote that functions according to the following
table: Touchmonitor/Computer Module status LED status
OFF OFF
SLEEP BLINKING
ON ON
The system consumes low power when in SLEEP and OFF modes. For detailed power
consumption specifications, refer to technical specifications available on the Elo website
www.elotouch.com.
Touching the screen will bring the system out of MONITOR SLEEP mode.
If long periods of disuse are planned, unplug the AC power cable to save power.
The maximum voltage, frequency and current for the touchmonitor are provided in the power
ratings table below:
Operating Voltage
Range
Operating Frequency
Range
Operating Current
Range
ET32/4201L 100 - 240Vac 50/60 Hz 3.6 – 1.5 A
ET5501L/ET5501LT 100 - 240Vac 50/60 Hz 5 – 2.1 A
ET7001L/ET7001LT 100 - 240Vac 50/60 Hz 5 – 2.1 A
To keep the product operating at an optimum level please limit the product usage cycle to 18
hours for every 24 hours:
Usage duty cycle:
18 hours on per 24 hours
Elo recommends using the Content Management System or O/S scheduling settings and/or EloView
commands to manage duty cycle. This will enable power savings and trouble free operation
throughout the life of the monitor.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 14 of 37
IntelliTouch Touchscreen Technology
The IntelliTouch and IntelliTouch Plus touchscreens can be re-calibrated to your displayed video
image, if needed, through the calibration function in the Elo driver control panel.
IntelliTouch Plus monitors require calibration if the video source is rotated.
Optical Touchscreens Technology
When connected to Windows 7 or Win 8.1 computers, the touchmonitor can report six
simultaneous touches.
InfraRed (IR) Touchscreens Technology
When connected to Windows 7 or Windows 8.1 computer, the touchmonitor can report ten
simultaneous touches.
Projective Capacitance Touchscreens Technology
When connected to Windows 7 computers, the touchmonitor can report ten simultaneous
touches.
Gesturing Images:
For multi-touch monitors, the following gestures are possible:
Single Touch Gestures and their Functions:
Swipe - The ability to swipe through from one picture to another or drag an icon
Dual Touch Gestures and their Functions:
Swipe – The action of moving a finger across the screen.
- The ability to swipe through from one picture to another or drag an icon
Pinch-Zoom - Zoom into a picture
- Place two fingers on the screen and move them closer together to zoom in. Move your fingers
away from each other to zoom out.
Before zoom After zoom

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 15 of 37
Rotate – A picture can be rotated 360°
In addition to the above gestures, Optical units have the ability to pinch and zoom three different
pictures at the same time because six simultaneous touches are supported.
Video
An LCD panels native resolution is its width and height measured in number of pixels.
In almost all cases, an image displayed on an LCD monitor will look best when your computers
output resolution matches the LCD panels native resolution. See the display specifications on
the Elo website www.elotouch.com to find your touchmonitors native resolution. Operating in
other resolutions will degrade video performance and is not recommended.
For computer output resolutions at non-native resolutions, the monitor will scale the video to
panel’s native resolution. For smaller input video resolutions, this involves “stretching” the input
image in the X- and Y-dimensions to fit the panel. For larger input video resolutions, this
involves “compressing” the input image in the X- and Y-dimensions to fit the panel. An
unavoidable byproduct of the scaling algorithms is a loss of fidelity when the computers output
video image is scaled by the monitor to fit the display. This loss of fidelity is most apparent when
viewing feature-rich images at close distances (for example images containing small-font text).
Your touchmonitor will likely not require video adjustments. However, for analog VGA video,
variations in video graphic card outputs may require touchmonitor adjustments through the
OSD to optimize the quality of the touchmonitors displayed image. To reduce the need for
adjustments for different video mode timings, the monitor correctly scales and displays some of
the video industries most common video timing modes.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 16 of 37
On-Screen Display (OSD) Connected Through the RJ45
Connection
Five OSD buttons can be found on the OSD remote. There is an LED light which shows the
current state of the monitor. The following are the functions that relate to the designated button.
The buttons and their functionality are:
Button Function when OSD is not displayed: Function when OSD is displayed:
Menu Display OSD main menu Return to previous OSD menu
Display OSD Audio source submenu Decrease value of selected parameter /
select previous menu item
Hot key for changing video source* Increase value of selected parameter /
select next menu item
Select Display Audio and Video Parameters Menu Select parameter for adjustment /
select submenu to enter
Power for the monitor Toggles the power status of the monitor
*The hot key allows the user to quickly change the input video source. If the user accidently
presses this key, they can quickly press the Menu button to cancel a video source change.
Using the OSD buttons controls an on-screen graphical user interface which displays on top of
your input video, allowing intuitive adjustment of the following display parameters:

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 17 of 37
Parameter Available Adjustment
Main Menu Video Settings, Audio Settings, Color Settings and Other Settings can be selected
Video Settings Video Source, Brightness, Contrast, Black Level, Sharpness and Aspect Ratio are
available in this menu.
Video Source Allows the user to switch between the available video sources.
Audio Settings Allows the user to toggle the mute setting. Also, the volume of the internal speakers
or headphones can be adjusted.
Default: Not Muted, Volume at 50
Color Settings Displays the Color Adjust and Color Preference Menus
HDMI Allows HDMI video to be displayed on the monitor
VGA Port Allows VGA video to be displayed on the monitor
DisplayPort Allows DisplayPort video to be displayed on the monitor
Elo Computer
Module ECM DP – DisplayPort is the standard video output of Elo Computer modules. If
HDMI video input is found, the video source can be switched.
Video Source
The monitor continually scans for active video from VGA, DisplayPort, HDMI, and
the Computer Module. This adjustment selects which of those input ports should be
displayed.
If an Elo Computer Module or Intel OPS computer module has been detected,
video priority is given to the computer module before any of the external sources.
Brightness Increase/decrease monitor brightness.
Default: 65
Contrast Increase/decrease monitor contrast.
Default: 50
VGA Settings Allows user to change the H. position, V. position, Clock and Phase.
If VGA is selected, the Auto-Adjust feature is available.
Sharpness
Adjusts sharpness of the displayed images.
Default: no sharpness adjustment
Sharpness function is disabled when the input source ratio is the same as the
panels native ratio
Aspect Ratio
Switches the scaling method between Fill Screen and Fill to Aspect Ratio.
Default: Fill Screen
Fill Screen – Scales the X- and Y-dimensions of the input video (up or down as
needed) to the displays native resolution.
Fill Aspect Ratio – Assuming a landscape orientation and an input video with
aspect ratio smaller than 16:9, scales the Y-dimension of the input video (up or
down as needed) to the displays Y-resolution, and scales the X-dimension to
maintain the aspect ratio (and fills the rest of the display with equal black bars on
the left and right).
- When the input source ratio is the same as the panel native ratio, this
function is disabled
Direct output - Input source is the same with output source and the image will be on
the center of the screen. No Scaling will occur.
Recalibration may be required when switching between these options.
Light Sensor The light sensor can be toggled on or off. When the light sensor is enabled, the
brightness cannot be changed manually.
Auto Adjust Automatically adjusts the system clock to the input analog VGA video signal,
affecting the H-position, V-position, Clock, and Phase menu items.
Not applicable when using HDMI video or the Computer Module.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 18 of 37
Clock Allows fine adjustments of the panels pixel dot clock.
Not applicable when using HDMI/DisplayPort video or the Computer Module.
Phase Allows fine adjustments of the panels pixel dot clock phase.
Not applicable when using HDMI/DisplayPort video or the Computer Module.
H-position Moves the image horizontally on the display in single-pixel increments.
Default: centered.
Not applicable when using HDMI/DisplayPort video or the Computer Module.
V-position Moves the image vertically on the display in single-pixel increments.
Default: centered.
Not applicable when using HDMI/DisplayPort video or the Computer Module.
Black Level
The user can choose between Standard, 5%, 10% or 15% black level offset.
The saturation level of the colors change according to the chosen black level offset.
Not available when the video source is from VGA.
Color
Temperature
Selects the displays color temperature. The available color temperatures are
9300K, 7500K, 6500K, 5500K, and User Defined. If the User Defined option is
selected, the user can change the color temperature by changing individual R, G,
and B gains on a scale from 0 to 100.
Default: User Defined with R, G, and B all set to 100.
Audio Source
Allows the user to choose the audio source. The choices are From Video Source,
Line in and ECM Line-in (available only if an ECM is detected)
If there is no Computer Module plugged in, and the video source is HDMI, the
options are: Line In and HDMI.
Default: Line In.
Color Adjust
The Color Temperature menu can be chosen or Hue and Saturation can be varied
in this menu.
Color Temperature will only be available in the Standard color preference mode.
Hue and Saturation are available in the remaining color preferences.
Color Preference
Standard, Movie, Gaming, Photo, Line or Legacy HDMI can be chosen depending
on the users preference.
Standard Mode: Color and Sharpness are set at an optimal level in this mode.
Recommended for use when displaying high quality images and video. This is the
default mode.
Movie, Gaming and Photo Modes: Allow the user to vary the Hue and Saturation
depending on application.
Line Mode: Recommended for use when displaying text or lines.
Legacy HDMI Mode: Black levels are lighter in comparison to Standard Mode. Only
applies if HDMI is the video source.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 19 of 37
All touchmonitor adjustments made through the OSD are automatically memorized as soon as
they are entered. This feature saves you from having to reset your choices every time the
touchmonitor is unplugged or powered off and on or if there is a power failure.
Other Settings
OSD menu: The Horizontal position, vertical position and OSD timer can be
changed from here.
Language Settings can be changed
Recall Defaults: set the system back to the preset standards
Information: display information about the monitor and system
MDC Protocol: allows the user to choose between DDC/CI and RS232 mode for
the MDC utility
Support & Help: Provide information about help and support
System Temperature: Provides the system Temperature information. If the Elo
computer module is inserted, there will be a secondary line showing that
temperature information.
Power Behavior: See section below for power behavior information
Video Port Discovery (only for 7001LT): If enabled, the monitor will automatically
switch video ports when a new video signal is detected.
OSD Timer Adjusts how long a period of OSD button inactivity the Touchmonitor will wait before
closing the OSD. The adjustable range is between 5 and 60 seconds.
Default: 15 seconds
OSD Language
Selects which language the OSD information is displayed in. The available
languages are: English, French, Italian, German, Spanish, Simplified Chinese,
Traditional Chinese, and Japanese.
Default: English.
OSD H-Position Moves the OSD location left and right on the display.
Default: 50 (centered)
OSD V-position Moves the OSD location up and down on the display.
Default: 50 (centered)
Recalling
Defaults
Selecting “Recall Defaults” restores all factory default settings for OSD-adjustable
parameters (except OSD Language and OSD Position) and for Preset Video Mode
timings.
Power Behavior
When power to the monitor is lost and regained, the behavior that is chosen will be
executed.
Always On
Always Off
Last State
MDC Protocol This menu allows the user to switch between the serial protocol and the DDC/CI
protocol.
DDC/CI protocol is used to communicate to a host computer via the video signal.
Tabletop Enables or disables the Tabletop Thermal Protection Mode settings
Information Displays Monitor Information, System Temperature and Help & Support options.
Nothing is adjustable in this menu.
Monitor
Information Displays the touchmonitor model and the monitor and touchscreen serial #
information
System
Temperature
Displays the real-time temperature of the Video Board
Note: Docking Board and the CPU Sensor temperatures are only available if these
features are supported by the computer module.
Help & Support Display information regarding Elo Touch Solutions contact information.

User Manual: Interactive Digital Signage
SW601990 Rev L, Page 20 of 37
OSD and Power Lockouts
Press and hold the “Menu” and “>” buttons for one seconds to enable/disable the OSD Locking
feature. When the OSD Locking is enabled, pressing any of the Menu, Up, Down, or Select
keys will have no effect on the system.
Press and hold the “Menu” and “<” buttons for one seconds to enable/disable the Power
Locking feature. When the Power Locking is enabled, pressing the power switch will have no
effect on the system.
Audio
Audio from the touchmonitor Line In, touchmonitor HDMI, touchmonitor DisplayPort, computer
module Line In, or computer module HDMI or DisplayPort ports can be played over the
touchmonitors internal speakers. See the “Audio Source” OSD parameter for details. When
headphones are plugged into the headphone output jack, the internal speakers turn off and
audio is played over the headphones.
Volume and muting of the speaker and headphone outputs can be controlled by the OSD.
MDC Functionality (For Remote Monitor Applications)
The touchmonitor has the ability to allow remote access from a host application. This is done
through the use of the Multiple Display Control command sets. By installing the IDS Utilities
Suite, the user can communicate with the monitor via the application. The host application can
send a variety of different instructions which will be executed on the IDS 01 series touchmonitor.
For detailed information regarding the command set, refer to the application note available
here.
A Y-Cable is included in the 7001LT which allows users to send serial commands via the VGA
port of the monitor. One connector of this cable is for the VGA video signal and the other
connector is for the RS232 signal (MDC).
RFID Functionality
For 3201L and 4201L Units:
There is an integrated RFID antenna within the monitor. To enable the RFID functionality, a
RFID reader module (available at www.elotouch.com) must be installed and connected to the
integrated monitor antenna. Refer to the RFID peripheral installation guide for proper hardware
and software installation techniques.
For the 5501L/5501LT and 7001L/7001LT units, an external peripheral kit is available from Elo.