elsner elektronik KNX RF-MSG-DST Guide

EN
Installation and Adjustment
Item number 70712
KNX RF-MSG-DST
Rad io actuator

1 Contents
Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany
Radio actuator KNX RF-MSG-DST • from software version 0.1.0 ETS programme version 1.0
Status: 27.06.2018 • Subject to technical changes. Errors excepted.
1. Description ........................................................................................... 3
1.0.1. Scope of delivery .......................................................................................... 3
1.1. Technical Data .......................................................................................................... 3
2. Installation and start-up ....................................................................... 4
2.1. Installation notes ...................................................................................................... 4
2.1.1. Safety advice ................................................................................................. 5
2.2. Notes on wireless equipment ................................................................................. 5
2.3. Connection ................................................................................................................ 5
2.3.1. Device Design ................................................................................................ 7
2.4. Establish radio connection ...................................................................................... 7
2.5. Activate retransmitter function ............................................................................... 8
2.6. Notes on mounting and commissioning ................................................................ 8
3. Transfer protocol ................................................................................. 9
3.1. List of all communication objects ........................................................................... 9
4. Parameter setting .............................................................................. 12
4.1. General settings ..................................................................................................... 12
4.2. Operating Mode ..................................................................................................... 12
4.2.1. Drive - Shutter, Blind, Awning, Window ................................................... 12
4.3. Control ..................................................................................................................... 15
4.3.1. Manual ......................................................................................................... 20
4.3.2. Automation – external ................................................................................ 21
4.3.3. Scenes ......................................................................................................... 21

2 Clarification of signs
This manual is amended periodically and will be brought into line with new software
releases. The change status (software version and date) can be found in the contents footer.
If you have a device with a later software version, please check
www.elsner-elektronik.de in the menu area "Service" to find out whether a more up-to-
date version of the manual is available.
Clarification of signs used in this manual
Installation, inspection, commissioning and troubleshooting of the device
must only be carried out by a competent electrician.
Safety advice.
Safety advice for working on electrical connections, components,
etc.
DANGER! ... indicates an immediately hazardous situation which will lead to
death or severe injuries if it is not avoided.
WARNING! ... indicates a potentially hazardous situation which may lead to
death or severe injuries if it is not avoided.
CAUTION! ... indicates a potentially hazardous situation which may lead to
trivial or minor injuries if it is not avoided.
ATTENTION! ... indicates a situation which may lead to damage to property if it is
not avoided.
“Control unit”
The symbol is followed by a menu path. In this menu the settings
just described can be changed.
“Manual”
The symbol is followed by chapter information with a page num-
ber. In this chapter you will find additional information about the
setting just described.

3 Description
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
1. Description
The KNX RF-MSG-DST is a radio actuator for KNX radio (KNX RF). The actuator con-
trols one drive (blind, shutter, awning or window). Via an additional connector, another
motor control unit is supplied with power (loop-through function).
The KNX RF-MSG-DST uses the KNX RF S standard.
Functions:
• 1 connection for 230 V-drive (STAK3)
• 1 output 230 V AC (STAK3) for supply of further motor control units
• Reception of the control signal via radio KNX RF
•Retransmitter function (from version 1.1): Forwarding of all received KNX
RF telegrams. These can be received by KNX RF participants with the same
domain address. This allows the range of the KNX RF signal to be increased
•Automatic runtime measurement of the drives for positioning (incl. fault
reporting object)
•Position feedback (movement position, also slat position for shutters)
•Position storage (movement position) via 1-bit object (storage and call-up
e.g. via buttons)
•Scene control for movement position with 16 scenes per drive (also slat
position for shutters)
•Blocking objects and alarm reports have different priorities, so safety
functions always take precedence (e.g. wind block)
• Manual or automatic priority setting via time or communication object
•Brief time limit (movement command blocked) and 2 movement limits
Configuration is made using the KNX software ETS 5. The product file can be down-
loaded from the ETS online catalogue and the Elsner Elektronik website on www.els-
ner-elektronik.de in the “Service” menu.
1.0.1. Scope of delivery
•Actuator
• Magnet for teaching procedure (telescopic rod)
• Rubber seal
Available accessories:
• Mains connection wire (5 m)
• Connection wire (available in 1 m; 2,5 m; 5 m)
1.1. Technical Data
Housing Plastic
Protection category IP 54*
Dimensions approx. 149 x 72 x 29 (W x H x D, mm)
Weight approx. 168 g
Ambient temperature Operation -25…+70 °C, storage -30…+85°C

4 Installation and start-up
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
*The Radio actuator KNX RF-MSG-DST should be installed in a protected area
despite a high protection category because water can enter in via the connectors.
Please observe the instructions in Chapter Connection.
The product conforms with the provisions of EU directives.
2. Installation and start-up
2.1. Installation notes
Installation, testing, operational start-up and troubleshooting should
only be performed by an electrician.
DANGER!
Risk to life from live voltage (mains voltage)!
There are unprotected live components within the device.
• VDE regulations and national regulations are to be followed.
• Ensure that all lines to be assembled are free of voltage and take
precautions against accidental switching on.
• Do not use the device if it is damaged.
• Take the device or system out of service and secure it against
unintentional use, if it can be assumed, that risk-free operation is no
longer guaranteed.
The device is only to be used for its intended purpose. Any improper modification or
failure to follow the operating instructions voids any and all warranty and guarantee
claims.
After unpacking the device, check it immediately for possible mechanical damage. If it
has been damaged in transport, inform the supplier immediately.
The device may only be used as a fixed-site installation; that means only when assem-
bled and after conclusion of all installation and operational start-up tasks and only in
the surroundings designated for it.
Ambient humidity max. 95% RH, avoid condensation
Operating voltage 230 V AC
Input STAS3 plug (230 V)
Output 1 x 230 V AC (loop-through), STAK3 coupling, max. 1.5
kW switch-on load per mains connection
1 × drive, STAK3 coupling, 230 V AC (up/down/N/PE),
loadable to max. 4 A / 230 V AC
Communication objects 52
Assignments max. 1024
Radio frequency 868,3 MHz

5 Installation and start-up
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.
2.1.1. Safety advice
WARNING!
Risk of injury caused by components moved automatically!
If the wireless connection between the control unit and the wireless
actuator is interrupted, connected devices can no longer be operated.
• For that reason do not connect drives to the wireless actuator which
could be hazardous to human life!
2.2. Notes on wireless equipment
When planning facilities with devices that communicate via radio, adequate radio re-
ception must be guaranteed. The range will be limited by legal regulation and struc-
tural circumstances. Avoid sources of interference and obstacles between receiver and
transmitter, that could disturb the wireless communication. Those would be for exam-
ple:
• Walls and ceilings (especially concrete and solar protection glazing).
• Metal surfaces next to the wireless participants (e. g. aluminium construction
of a conservatory).
• Other wireless devices and powerful local transmitters (e.g. wireless
headphones), which transmit on the same frequency. Please maintain a
minimum distance of 30 cm between wireless transmitters for that reason.
2.3. Connection
The radio module is connected between the appliance and the power supply. It may
only be connected to flexible lines using STAK/STAS connectors. The connectors must
be locked using the locking bow.
Do not expose to continuous sun radiation to avoid overheating.
The housing is not UV-resistant.
• Assembly the device in a protected area (e. g. in
the box for the blinds/marquee/shutters in a construction
profile beneath the roof tiles or in a housing).
The antenna symbol on the housing shows the
position of the antenna in KNX RF-MSG-DST. This
side must not be positioned directly on metal
surfaces or objects. Otherwise, the radio signal might
disturbed.
Metal
profile
KNX RF-MSG-DST

6 Installation and start-up
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
No water may run along the supply line and device because water
can enter in via the connectors.
• Assembly the device in a protected area (e. g. in
the box for the blinds/marquee/shutters in a construction
profile beneath the roof tiles or in a housing).
• Lay the supply lines out and down from the device.
No vibrations!
• Assemble the device in a place that is free of vibrations.

7 Installation and start-up
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
2.3.1. Device Design
2.4. Establish radio connection
The device is integrated into the KNX system with a media coupler or a KNX RF USB
stick. (For further information see the corresponding manual/data sheet.)
1. Start the programming mode of the KNX RF-MSG with the enclosed magnet (teles-
copic rod). The programming LED lights up.
1 Neutral conductor
2L
3 nc (not connected)
PE
Motor output
STAK3 coupling
for STAK3 plug
Input mains voltage
STAS3 plug for
STAK3 coupling
1Neutralcond.
2Up
3Down
PE
Output
mains voltage
STAK 3 coupling
for STAK3 plug
1 Neutral cond.
2L
3nc(
PE
PRG
Magnet
(side)
and LED
PE
PE
PE
1
32
1
32
3
2

8 Installation and start-up
Radio actuator KNX RF-MSG-DST • Version:27.06.2018 • Technical changes and errors excepted.
2.5. Activate retransmitter function
2.6. Notes on mounting and commissioning
Device must not be exposed to water (rain). This could result in the electronic being
damaged. A relative air humidity of 95% must not be exceeded. Avoid bedewing.
If the device is set up as a retransmitter, it transmits
all received KNX RF telegrams. These can be recei-
ved by KNX RF participants with the same domain
address. As a result, the radio range of a KNX RF
system can be increased.
The function must be activated in the ETS in the pro-
perty window of the device by ticking the box "Re-
transmitter".