Emerson Fisher FIELDVUE DVC6000 User manual

FisherrFIELDVUE™ DVC6000 Digital Valve
Controllers Instruction Manual
(Supported)
Supported products may not be manufactured again in any Emerson Process Management location under any
conditions. Spare parts availability is 7 years of best effort. Technical support is available.
Post‐sale documents (such as instruction manuals and quick start guides) are available on the CD and FishWeb. Many
are also available at www.fisher.com.
Instruction manuals for supported products may be updated, if required, to support products in the field.
Pre‐sale documents (such as bulletins) for supported products are included on FishWeb for internal use. They are not
included on the CD.
Supported Product
D102794X012
DVC6000 Digital Valve Controllers
October 2013
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
E2013 Fisher Controls International LLC. All rights reserved.
Fisher and FIELDVUE are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric Co. Emerson Process
Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective
owners.
Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.

Introduction and Specifications
Installation
Basic Setup
Detailed Setup
Calibration
Viewing Device Variables and Diagnostics
Maintenance and Troubleshooting
Parts
Appendices
Principle of Operation
Loop Schematics/Nameplates
Glossary
Index
DVC6000 Digital Valve Controllers Instruction Manual
D102794X012
September 2013
FisherrFIELDVUEtDVC6000
Digital Valve Controllers
This manual applies to:
Instrument Level AC, HC, AD, PD HC, AD, PD, ODV AC
Device Type 03 03 07
Device Revision 1 2 2
Hardware Revision 1 1 1
Firmware Revision 2−67, 9, 10, 11 7, 9, 10, 11
DD Revision 4 8 1
Refer to Related Documents on page 1-3 for other documents containing
information related to DVC6000 digital valve controllers
www.Fisher.com
1
2
3
4
5
6
7
8
9
A
A
B
C
14
Glossary
Index

DVC6000 Digital Valve Controllers
i
Fast Key Sequence for Instrument Level HC, AD, PD, and ODV
Function/Variable Fast-Key
Sequence Coordinates(1) Function/Variable Fast-Key Sequence Coordinates(1)
A Minus B 3-5-3 4-G End Point Pressure Control(3) 1-2-2-2-4 8-D
Actuator Style 1-2-6-4 3-D Failure Group Enable 1-2-3-6-5-1 11-I
Alert Conditions 2-1 2-F 1-2-3-7-5-1
Alert Record Full Enable 1-2-3-6-2 10-H Firmware Revision 3-7-6 2-H
1-2-3-7-2 Flash ROM Shutdown 1-2-3-1-3-5 12-C
Alert Record Has Entries Enable 1-2-3-6-1 10-H Hardware Revision 3-7-7 2-H
1-2-3-7-1 HART Tag 1-2-5-1-1 6-F
Analog Input 3-1 2-G 3-7-1 2-H
Analog Input Calibration 1-3-2-3 4-E HART Universal Revision 3-7-9 2-H
Analog Input Range Hi 1-2-5-3-1 6-H Input Characterization 1-2-2-3 4-C
Analog Input Range Lo 1-2-5-3-2 6-H Instrument Date and Time 1-2-4-1-2 8-G
Analog Input Units 1-2-5-2-3 6-G 1-2-5-8 4-G
Auto Calibration 1-3-1-1 4-E Instrument Level 3-7-8 2-H
Autocalibration in Progress Enable 1-2-4-2-2 8-H Instrument Mode Hot Key-1 1-A
Auxiliary Input 3-6-1 4-H 1-2-1-1 4-B
1-2-3-3-1-2 12-D Instrument Serial Number 1-2-5-1-6 6-G
Auxiliary Terminal Action 1-2-3-3-1-3 12-E Instrument Time Invalid Enable 1-2-4-1-1 8-G
1-2-5-7 4-G Integral Dead Zone 1-2-4-4-4 8-I
Auxiliary Terminal Alert Enable 1-2-3-3-1-1 12-E 1-2-2-1-2-1 8-B
Burst Command 1-2-1-4-3 6-B Integral Enable (Travel Tuning) 1-2-2-1-1-2 8-A
Burst Enable 1-2-1-4-1 6-B Integral Enable (Pressure Tuning) 1-2-2-1-3-2 8-C
Calibration in Progress Enable 1-2-4-2-1 8-G Integral Gain (Travel Tuning) 1-2-2-1-1-3 8-A
Clear ALL Records 1-2-3-6-4 10-H Integral Gain (Pressure Tuning) 1-2-2-1-3-3 8-C
1-2-3-7-4 Integral Limit 1-2-4-4-3 8-I
Command 3 Configured Pressure 1-2-1-4-5 6−B1-2-2-1-2-2 8-B
Control Mode Hot Key-2 1-A Integrator Saturated Hi Enable 1-2-4-4-1 8-I
1-2-1-2 4-B Integrator Saturated Lo Enable 1-2-4-4-2 8-I
Critical NVM Shutdown 1-2-3-1-3-4 12-C Last AutoCalibration Status 1-2-5-9-1 6-H
Custom Characterization Table 1-2-2-4 4-C Last Calibration Type 1-2-5-9-2 6-H
Cutoff Hi 1-2-3-4-7-3 12-G Loop Current Validation Enable(6) 1-2-3-3-3 9-E
1-2-2-2-2-1 10-B Low Power Write Fail Enable(6) 1-2-3-1-3-2 12-B
Cutoff Lo 1-2-3-4-7-4 12-G Manual Calibration 1-3-1-2 4-E
1-2-2-2-2-2 10-B Manufacturer (Actuator) 1-2-6-1 3-D
Cycle Counter 1-2-3-5-1-2 12-H Manufacturer (Instrument) 3-7-3 2-H
3-6-5 4-H Maximum Recorded Temperature 3-6-3 4-H
Cycle Counter Alert Enable 1-2-3-5-1-1 12-G 2-3-1 3-F
Cycle Count Alert Point 1-2-3-5-1-3 12-H Maximum Supply Pressure 1-2-5-6 4-G
Date 1-2-5-1-4 6-G Message 1-2-5-1-2 6-F
Dead Band (Cycle Count / Travel
Accumulator) 1-2-3-5-2-1 12-H Minimum Recorded Temperature 2-3-2 3-F
Descriptor 1-2-5-1-3 6-F 3-6-4 4-H
Device Description Information 3-8 2-G Miscellaneous Group Enable 1-2-3-6-5-3 11-I
Device ID 3-7-2 2-H 1-2-3-7-5-3
Device Revision 3-7-5 2-H Model (Device) 3-7-4 2-H
Diagnostic Data Available Enable 1-2-4-2-4 8-H Multi-Drop Alert Enable 1-2-4-3-2 8-H
Diagnostic in Progress Enable 1-2-4-2-3 8-H No Free Time Shutdown 1-2-3-1-3-6 12-C
Drive Current Shutdown 1-2-3-1-1 8-D Non-Critical NVM Alert Enable 1-2-3-1-3-3 12-C
Drive Signal Alert Enable 1-2-3-1-2-1 10-D Number of Power Ups 2-3-4 3-G
Drive Signal 3-4 2-G 3-6-9 4-H
1-2-3-1-2-2 10-D Offline/Failed Alert Enable 1-2-3-1-3-1 12-B
NOTE: Italicized Fast-Key Sequence indicates fast-key sequence is applicable only for instrument level ODV.
1. Coordinates are to help locate the item on the menu tree on the following pages.
3. Instrument level ODV only.
5. Instrument level HC, AD, and PD only.
6. Firmware 9 and 10 only.

DVC6000 Digital Valve Controllers
ii
Fast Key Sequence for Instrument Level HC, AD, PD, and ODV
Function/Variable Fast-Key
Sequence Coordinates(1) Function/Variable Fast-Key Sequence Coordinates(1)
Partial Stroke Test(3) 2-5 2-F Travel 3-3 2-G
Partial Stroke Test Enable(3) 1-2-7-1 3-D 1-2-3-4-1 9-E
Partial Stroke Test Pressure Limit(3) 1-2-3-6-1 10-G Travel / Pressure Select 1-2-2-2-1 6-C
Partial Stroke Test Start Point(3) 1-2-2-2-4-2 8-D Travel Accumulatorv 3-6-6 4-H
Partial Stroke Test Variables
View/Edit(3) 1-2-7-2 3-D 1-2-3-5-3-2 12-H
Performance Tuner(2) 1-1-2 2-B Travel Accumulator Alert Enable 1-2-3-5-3-1 12-H
1-2-2-1-1-5 8-A Travel Accumulator Alert Point 1-2-3-5-3-3 12-I
Polling Address 1-2-5-1-7 6-G Travel Alert Dead Band 1-2-3-4-3 9-E
Pressure A 3-5-1 4-G Travel Alert Hi Enable 1-2-3-4-6-1 10-F
Pressure B 3-5-2 4-G Travel Alert Hi Hi Enable 1-2-3-4-5-1 12-E
Pressure Control Active Enable 1-2-4-3-1 8-H Travel Alert Hi Hi Point 1-2-3-4-5-3 12-F
Pressure Deviation Alert Enable(3) 1-2-3-6-2 10-G Travel Alert Hi Point 1-2-3-4-6-3 10-F
Pressure Deviation Alert Point(3) 1-2-3-6-3 10-G Travel Alert Lo Enable 1-2-3-4-6-2 10-F
Pressure Deviation Time(3) 1-2-3-6-4 10-G Travel Alert Lo Lo Enable 1-2-3-4-5-2 12-E
Pressure Range Hi 1-2-2-2-3-1 10-D Travel Alert Lo Lo Point 1-2-3-4-5-4 12-F
Pressure Range Lo 1-2-2-2-3-2 10-D Travel Alert Lo Point 1-2-3-4-6-4 10-F
Pressure Sensor Shutdown(2) 1-2-3-2-3 12-D Travel Deviation Alert Enable 1-2-3-4-4-1 10-E
Pressure Sensors—Calibration 1-3-2-1 4-E Travel Deviation Alert Point 1-2-3-4-4-2 10-E
Pressure Tuning Set 1-2-2-1-3-1 8-B Travel Deviation Time 1-2-3-4-4-3 10-E
Pressure Units 1-2-5-2-1 6-G Travel Limit / Cutoff Hi Enable 1-2-3-4-7-1 12-F
Protection Hot Key-3 1-A Travel Limit / Cutoff Lo Enable 1-2-3-4-7-2 12-F
1-2-1-5 4-B Travel Limit Hi 1-2-3-4-7-6 12-G
Raw Travel Input 3-6-7 4-H 1-2-2-2-2-4 10-C
Reference Voltage Shutdown 1-2-3-1-3-7 12-C Travel Limit Lo 1-2-3-4-7-7 12-G
Relay Adjust 1-3-3 3-E 1-2-2-2-2-5 10-C
Relay Type 1-2-5-4 4-F Travel Sensor Adjust 1−3−2−2 4−E
Restart Control Mode 1-2-1-3 4-B Travel Sensor Motion 1-2-6-5 3-E
Restore Factory Settings 1-3-4 3-E Travel Sensor Shutdown 1-2-3-2-1 12-C
Set Point Rate Close 1-2-2-5-2 5-D Travel Setpoint 1-2-3-4-2 9-E
Set Point Rate Open 1-2-2-5-1 5-D 3-2 2-G
Setup Wizard 1-1-1 2-B Travel Tuning Set 1-2-2-1-1-1 8-A
Stabilize/Optimize Hot Key-4 1-A Valve Group Enable 1-2-3-6-5-2 10-H
1-1-2(4) 2-B 1-2-3-7-5-2
1-2-2-1-1-4 8-A Valve Serial Number 1-2-5-1-5 6-F
Status 2-2 2-F 1-2-6-2 3-D
Stroke Valve 2-4 2-F Valve Style 1-2-6-3 3-D
Supply Pressure(2) 3-5-4 4-G View Alert Records 1-2-3-6-3 10-H
1-2-3-3-2-2 12-E 1-2-3-7-3
Supply Pressure Lo Alert Enable(5) 1-2-3-3-2-1 12-E View/Edit Feedback Connection 1-2-6-6 3-E
Supply Pressure Lo Alert Point(5) 1-2-3-3-2-3 12-E View/Edit Lag Time(5) 1-2-2-5-3 5-D
Temperature 3-6-2 4-H View/Edit Lead/Lag(3) 1-2-2-5-3 5-D
Temperature Sensor Shutdown 1-2-3-2-2 12-D View Number of Days Powered Up 2-3-3 3-F
Temperature Units 1-2-5-2-2 6-G 3-6-8 4-H
Zero Power Condition 1-2-5-5 4-G
NOTE: Italicized Fast-Key Sequence indicates fast-key sequence is applicable only for instrument level ODV.
1. Coordinates are to help locate the item on the menu tree on the following pages.
2. Not available in instrument level HC.
3. Instrument level ODV only.
4. Instrument level HC only.
5. Instrument level HC, AD, and PD only.6
7. Firmware 7 only.

DVC6000 Digital Valve Controllers
iii
Hot Key
1 Instrument Mode
2 Control Mode
3 Protection
4 Stabilize/Optimize
Notes:
1-1-1 indicates fast-key sequence to reach menu
1 This menu is available by pressing the left
arrow key from the previous menu.
2 Not available in instrument level HC
3 Instrument level ODV only.
4 Instrument level HC only.
5 Instrument level HC, AD, and PD only.
6 Fast key sequence for Alert Record with instrument level ODV is 1-2-3-7.
7 This menu item reads Power Starvation Alrt Enab in firmware 7 and below.
8 Only available in firmware 9, 10, and 11.
1‐1
1
Field Communicator Menu Tree for
Instrument Level HC, AD, PD, and ODV
1
1‐2‐1
1-2
1‐2‐4
1‐2‐1‐4
1‐2‐5
1‐2‐6
1‐3
1‐3‐1
1‐3‐2
2
3‐5
3‐6
123456
3
5
2
2‐3
1‐2‐7
1‐2‐3
3‐7
3
3
1‐2‐2
1‐2‐5‐2
1‐2‐5‐3
41‐2‐2‐1
1‐2‐2‐2
1‐2‐2‐5
2
1‐2‐5‐9
1‐2‐5‐1
Guided Setup
1 Setup Wizard
2 Performance Tuner
2 Stabilize/Optimize
Detailed Setup
1 Mode and Protection
2 Response Control
3 Alert Setup
4 Status
5 Instrument
6 Valve and Actuator
7 SIS/Partial Stroke
Online
1 Configure
2 Service Tools
3 Overview
Configure
1 Guided Setup
2 Detailed Setup
3 Calibrate
HART Application
1 Offline
2 Online
3 Utility
4 HART Diagnostics
Calibrate
1 Travel Calibration
2 Sensor Calibration
3 Relay Adjust
4 Restore Factory Settings
5 PST Calibration
Partial Stroke
1 PST Enable
2 PST Enable
3 PST Vars View/Edit
Burst Mode
1 Burst Enable
2 Change Burst Enable
3 Burst Command
4 Change Burst Command
5 Cmd 3 Configured Pressure
Mode and Protection
1 Instrument Mode
2 Control Mode
3 Restart Control Mode
4 Burst Mode
5 Protection
Device Information
1 HART Tag
2 Device ID
3 Manufacturer
4 Model
5 Device Revision
6 Firmware Revision
7 Hardware Revision
8 Instrument Level
9 HART Universal Revision
Variables
1 Auxiliary Input
2 Temperature
3 Maximum Recorded Temperature
4 Mininum Recorded Temperature
5 Cycle Counter
6 Travel Accumulator
7 Raw Travel Input
8 View Number of Days Powered Up
9 Number of Power Ups
Pressure
1 Pressure A
2 Pressure B
3 A Minus B
4 Supply
Service Tools
1 Alert Conditions
2 Status
3 Device Record
4 Stroke Valve
5 Partial Stroke Test
Overview
1 Analog In
2 Setpoint
3 Travel
4 Drive Signal
5 Pressure
6 Variables
7 Device Information
8 DD Information
Device Record
1 Maximum Recorded
Temperature
2 Mininum Recorded
Temperature
3 View Number of Days
Powered Up
4 Number of Power Ups
Response Control
1 Tuning
2 Travel/Pressure Control
3 Input Characterization
4 Custom Characterization Table
5 Dynamic Response
Travel Calibration
1 Auto Calibration
2 Manual Calibration
Sensor Calibration
1 Pressure Sensors
2 Travel Sensor
3 Analog In
Alert Setup
1 Electronics Alerts
2 Sensor Alerts
3 Environment Alerts
4 Travel Alerts
5 Travel History Alerts
6 SIS Alerts
6 Alert Record
Valve & Actuator
1 Manufacturer
2 Valve Serial Number
3 Valve Style
4 Actuator Style
5 Travel Sensor Motion
6 View/ Edit Feedback
Connection
7 Assembly Specification Sheet
Tuning
1 Travel Tuning
2 Integral Settings
3 Pressure Tuning
Travel/Pressure Control
1 Travel/Pressure Select
2 Cutoffs and Limits
3 Pressure Control
4 End Point Pressure Control
Dynamic Response
1 SP Rate Open
2 SP Rate Close
3 View/Edit Lag Time
3 View/Edit Lead/Lag
Instrument
1 General
2 Units
3 Analog Input Range
4 Relay Type
5 Zero Power Condition
6 Maximum Supply Pressure
7 Auxiliary Terminal Action
8 Instrument Date and Time
9 Calib Status and Type
Status
1 Instrument Time
2 Calibration and Diagnostics
3 Operational
4 Integrator Saturation
Units
1 Pressure Units
2 Temperature Units
3 Analog In Units
Analog Input Range
1 Input Range Hi
2 Input Range Lo
Calib Status and Type
1 Last AutoCal Status
2 Last Calibration Type
General
1 HART Tag
2 Message
3 Descriptor
4 Date
5 Valve Serial Number
6 Instrument Serial Number
7 Polling Address
36
3
3

DVC6000 Digital Valve Controllers
iv
Alert Record
1 Alert Record Has Entries Enable
2 Alert Record Full Enable
3 View Alert Records
4 Clear ALL Records
5 Alert Groups
78 910 11
A
B
C
D
E
F
G
H
I
12
Electronics Alerts
1 Drive Current Shutdown
2 Drive Signal Alert
3 Processor Impaired Alerts
Travel Tuning
1 Travel Tuning Set
2 Integral Enable
3 Integral Gain
4 Stabilize / Optimize
5 Performance Tuner
Integral Settings
1 Integral Dead Zone
2 Integral Limit
Pressure Tuning
1 Pressure Tuning Set
2 Integral Enable
3 Integral Gain
Cutoffs and Limits
1 Cutoff Hi
2 Cutoff Lo
3 Change Cutoffs
4 Travel Limit Hi
5 Travel Limit Lo
6 Change Travel Limits
Pressure Control
1 Pressure Range Hi
2 Pressure Range Lo
Drive Signal Alert
1 Drive Signal Alert Enable
2 Drive Signal
Processor Impaired Alerts
1 Offline/Failed Alert Enable
2 Low Power Write Fail Enable
3 Non-Critical NVM Alert Enable
4 Critical NVM Shutdown
5 Flash ROM Shutdown
6 No Free Time Shutdown
7 Reference Voltage Shutdown
Sensor Alerts
1 Travel Sensor Shutdown
2 Temp Sensor Shutdown
3 Pressure Sensor Shutdown
Environment Alerts
1 Auxiliary Terminal Alert
2 Supply Pressure Lo Alert
3 Loop Current Validation
Enable
Travel Limit Alerts
1 Travel Alert Hi Hi Enable
2 Travel Alert Lo Lo Enable
3 Travel Alert Hi Hi Point
4 Travel Alert Lo Lo Point
Travel Alerts
1 Travel
2 Setpoint
3 Travel Alert DB
4 Travel Deviation Alert
5 Travel Limit Alerts
6 Travel Limit Hi/Lo Alerts
7 Travel Limit/Cutoff Alerts
Travel History Alerts
1 Cycle Counter
2 Cycle Count/Travel Accumulator
Deadband
3 Travel Accumulator
Travel Limit Hi/Lo Alerts
1 Travel Alert Hi Enable
2 Travel Alert Lo Enable
3 Travel Alert Hi Point
4 Travel Alert Lo Point
Travel Limit/Cutoff Alerts
1 Travel Limit/Cutoff Hi Enable
2 Travel Limit/Cutoff Lo Enable
3 Cutoff Hi
4 Cutoff Lo
5 Change Cutoffs
6 Travel Limit Hi
7 Travel Limit Lo
8 Change Travel Limits
Integrator Saturation
1 Integrator Sat Hi Enable
2 Integrator Sat Lo Enable
3 Integral Limit
4 Integral Dead Zone
Travel Deviation Alert
1 Travel Deviation Alert Enable
2 Travel Deviation Alert Point
3 Travel Deviation Time
Travel Accumulator
1 Travel Accumulator Alert Enable
2 Travel Accumulator
3 Travel Accumulator Alert Point
Cycle Counter
1 Cycle Counter Alert Enable
2 Cycle Counter
3 Cycle Count Alert Point
Instrument Time
1 Inst Time Invalid Enable
2 Instrument Date and Time
Calibration and Diagnostics
1 Calibration in Progress Enable
2 Autocal in Progress Enable
3 Diagnostic in Progress Enable
4 Diagnostic Data Avail Enable
Operational
1 Pressure Control Active Enable
2 Multi-Drop Enable
1‐2‐2‐1‐1
1‐2‐2‐2‐2
1‐2‐3‐1
1‐2‐3‐1‐2
End Point Pressure Control
1 End Pt Control Enab
2 PST Start Point
3 EPPC Setup Point
4 EPPC Saturation Time
1‐2‐2‐2‐4
SIS Alerts
1 PST Pressure Limit
2 Pressure Deviation Alert Enable
3 Pressure Deviation Alert Point
4 Pressure Deviation Time
ODV
Supply Press Lo Alert
1 Supply Pressure Lo Alert Enable
2 Supply
3 Supply Pressure Lo Alert Point
Auxiliary Terminal Alert
1 Auxiliary Terminal Alert Enable
2 Auxiliary Input
3 Auxiliary Terminal Action
Alert Groups
1 Failure Group Enable
2 Valve Group Enable
3 Miscellaneous Group Enable
Cycle Count/Travel Accumulator
Deadband
1 Deadband
1‐2‐3‐6
1‐2‐3‐2
1-2-3-3
1‐2‐3‐5
1‐2‐3‐6
1‐2‐3‐7
1‐2‐2‐1‐2
1‐2‐2‐1‐3
1‐2‐3‐5‐1
ODV
2
ODV
HC, AD, PD
1‐2‐3‐6‐5
1‐2‐3‐7‐5
1‐2‐4‐2
1‐2‐4‐3
1‐2‐4‐4
3
HC, AD, PD
1‐2‐2‐2‐3
1‐2‐4‐1
1‐2‐3‐5‐3
1‐2‐3‐5‐2
1‐2‐3‐1‐3
1-2-3-4
1‐2‐3‐3‐1
1‐2‐3‐4‐4
1-2-3-4-5
1‐2‐3‐4‐7
8
1‐2‐3‐3‐2
1‐2‐3‐4‐6
3
7

DVC6000 Digital Valve Controllers
v
Fast Key Sequence for Instrument Level AC
Function/Variable Fast-Key
Sequence Coordinates(1) Function/Variable Fast-Key Sequence Coordinates(1)
Actuator Style 1-1-2-2-4 4-C Pressure Proportional Gain 1-1-2-3-2-2 6-D
Analog Input Calibration 1-3-1 3-F 1-2-3-4-1-2 5-H
Analog Input Range Hi 1-2-2-2 4-E Pressure Range Hi 1-2-3-5-1 4-G
Analog Input Range Lo 1-2-2-3 4-E Pressure Range Lo 1-2-3-5-2 4-G
Analog Input Units 1-2-2-1 4-E Pressure Tuning Set 1-1-2-3-2-1 6-D
Auto Travel Calibration 1-1-2-3-4 4-D 1-2-3-4-1-1 6-G
1-3-2 3-F Pressure Units 1-1-2-2-2 4-C
1-1-1-3 3-C 1-2-2-4 4-E
Calibration Location 1-3-5 3-G Protection Hot Key-2 1-B
Date 1-2-1-4 3-D Relay Adjust 1-1-1-2 3-B
Descriptor 1-2-1-3 3-D 1-1-2-3-3 4-D
Device Description Revision 2-2 2-F 1-3-6 3-G
Device Identification 2-1-6 3-H Relay Type 1-2-4 3-E
Device Revision 2-1-2 3-G Restore Factory Settings 1-3-4 3-F
Feedback Connection 1-1-2-2-5 4-C Setup Wizard 1-1-1-1 3-D
Firmware Revision 2-1-3 3-G Travel Integral Gain 1-2-3-2-3 6-F
Hardware Revision 2-1-4 3-G Travel Integral Enable 1-2-3-2-2 6-F
HART Tag 1-2-1-1 3-D Travel MLFB Gain 1-1-2-3-1-4 6-C
HART Universal Revision 2-1-1 3-G 1-2-3-2-1-4 6-E
Input Characterization 1-2-3-6 4-F Travel / Pressure Select 1-1-2-2-1 4-C
Instrument Level 2-1-5 3-H 1-2-3-1 4-F
Instrument Mode Hot Key-1 1-B Travel Proportional Gain 1-1-2-3-1-2 6-C
1-1-2-1 3-C 1-2-3-2-1-2 6-E
Instrument Serial Number 1-2-1-6 3-D Travel Sensor Adjust 1-3-7 3-G
Integral Dead Zone 1-2-3-3-1 6-F Travel Sensor Motion 1-1-2-2-6 4-C
Integral Limit 1-2-3-3-2 6-F Travel Tuning Set 1-1-2-3-1-1 6-C
Manual Travel Calibration 1-3-3 3-F 1-2-3-2-1-1 6-E
Maximum Supply Pressure 1-1-2-2-3 4-C Travel Velocity Gain 1-1-2-3-1-3 6-C
Message 1-2-1-2 3-D 1-2-3-2-1-3 6-E
Polling Address 1-2-1-7 3-E Valve Serial Number 1-2-1-5 3-D
Pressure Integral Control Enable 1-2-3-4-2 6-G Valve Style 1-1-2-2-7 4-C
Pressure Integral Gain 1-2-3-4-3 6-G Zero Power Condition 1-1-2-2-8 4-C
Pressure MLFB Gain 1-1-2-3-2-3 6-D
1-2-3-4-1-3 5-H
1. Coordinates are to help locate the item on the menu tree on the facing page.

DVC6000 Digital Valve Controllers
vi
12 34 5
A
B
C
D
E
F
G
H
I
6
Field Communicator Menu Tree for
Instrument Level AC
Online
1 Setup
2 Display Calibrate
1 Analog In Calib
2 Auto Travel Calib
3 Man Travel Calib
4 Restore Factory Settings
5 Calib Loc
6 Relay Adjust
7 Tvl Sensor Adjust
General
1 HART Tag
2 Message
3 Descriptor
4 Date
5 Valve Serial Num
6 Inst Serial Num
7 Polling Address
Auto Setup
1 Setup Wizard
2 Relay Adjust
3 Auto Travel Calib
Device Information
1 HART Univ Rev
2 Device Rev
3 Firmware Rev
4 Hardware Rev
5 Inst Level
6 Device ID
Setup
1 Basic Setup
2 Detailed Setup
3 Calibrate
Basic Setup
1 Auto Setup
2 Manual Setup
Detailed Setup
1 General
2 Measured Var
3 Response Control
4 Relay Type
Display
1 Device Information
2 DD Revision
HART Application
1 Offline
2 Online
3 Utility
4 HART Diagnostics
Manual Setup
1 Instrument Mode
2 Press & Actuator
3 Tuning & Calib
Response Control
1 Tvl/Press Select
2 Tvl Tuning
3 Integral Settings
4 Press Tuning
5 Pressure Control
6 Input Char
Notes:
1‐1‐1 indicates fast‐key sequence to reach menu
This menu is available by pressing the left
arrow key from the previous menu.
1‐1
1‐1‐1
1‐1‐2
1‐2
1‐2‐1
1‐2‐3
2
1‐3
2‐1
1
1
Press & Actuator
1 Tvl/Press Select
2 Pressure Units
3 Max Supply Press
4 Actuator Style
5 Feedback Conn
6 Tvl Sensor Motion
7 Valve Style
8 Zero Pwr Cond
Tuning & Calib
1 Tvl Tuning Set
2 Press Tuning Set
3 Relay Adjust
4 Auto Travel Calib
1‐1‐2‐2
1‐1‐2‐3
1
Measured Var
1 Analog In Units
2 Input Range Hi
3 Input Range Lo
4 Pressure Units
1‐2‐2
Tvl Tuning
1 Tvl Tuning Set
2 Tvl Integ Enab
3 Tvl Integ Gain
1‐2‐3‐3
Press Tuning
1 Press Tuning Set
2 Press Integ Enab
3 Press Integ Gain
1‐2‐3‐4
1‐2‐3‐2
Integral Settings
1 Integ DeadZ
2 Integ Limit
Tvl Tuning Set
1 Tvl Tuning Set
2 Tvl Prop Gain
3 Tvl Velocity Gain
4 Tvl MLFB Gain
Tvl Tuning Set
1 Tvl Tuning Set
2 Tvl Prop Gain
3 Tvl Velocity Gain
4 Tvl MLFB Gain
Pressure Control
1 Press Range Hi
2 Press Range Lo
Press Tuning Set
1 Press Tuning Set
2 Press Prop Gain
3 Press MLFB Gain
Press Tuning Set
1 Press Tuning Set
2 Press Prop Gain
3 Press MLFB Gain
1‐1‐2‐3‐1
1‐1‐2‐3‐2
1-2-3-5
1‐2‐3‐2‐1
1‐2‐3‐4‐1
Hot Key
1 Instrument Mode
2 Protection
Setup
1 Basic Setup
2 Detailed Setup
3 Calibrate

DVC6000 Digital Valve Controllers
vii
FIELDVUE DVC6000 Digital Valve Controller
THE FIELDVUE DVC6000 DIGITAL VALVE CONTROLLERS IS A CORE COMPONENT OF THE PLANTWEBt
DIGITAL PLANT ARCHITECTURE. THE DIGITAL VALVE CONTROLLER POWERS PLANTWEB BY
CAPTURING AND DELIVERING VALVE DIAGNOSTIC DATA. COUPLED WITH VALVELINKtSOFTWARE,
THE DVC6000 PROVIDES USERS WITH AN ACCURATE PICTURE OF VALVE PERFORMANCE, INCLUDING
ACTUAL STEM POSITION, INSTRUMENT INPUT SIGNAL AND PNEUMATIC PRESSURE TO THE
ACTUATOR. USING THIS INFORMATION, THE DIGITAL VALVE CONTROLLER DIAGNOSES NOT ONLY
ITSELF, BUT ALSO THE VALVE AND ACTUATOR TO WHICH IT IS MOUNTED.

Introduction and Specifications
September 2013 1-1
Section 1 Introduction
Scope of Manual 1-2........................................................
Conventions Used in this Manual 1-2.....................................
Description 1-3..............................................................
Specifications 1-3...........................................................
Related Documents 1-3.....................................................
Educational Services 1-4...................................................
1

DVC6000 Digital Valve Controllers
September 2013
1-2
Table 1-1. Instrument Level Capabilities
CAPABILITY DIAGNOSTIC LEVEL(1)
AC HC AD PD ODV
Auto Calibration XXXXX
Custom Characterization XXXXX
Burst Communication X X X X
Alerts X X X X
Step Response, Drive Signal Test & Dynamic Error Band XXX
Advanced Diagnostics (Valve Signature) XXX
Performance Tuner XXX
Travel Control - Pressure Fallback XXX
Performance Diagnostics X X
Solenoid Valve Testing X X
Lead/Lag Input Filter(2) X
1. See page 6-8 for additional diagnostic level information.
2. Refer to brochure part # D351146X012/D351146X412 for information on Fisher optimized digital valves for compressor antisurge applications.
Scope of Manual
This instruction manual includes specifications,
installation, operating, and maintenance information
for device revision 1, firmware revision 2−6 and device
revision 2, firmware 7, 9, 10, and 11 digital valve
controllers, instrument level AC, HC, AD, PD, and
ODV.
This instruction manual describes using the 475 Field
Communicator with device description revision 8 to
setup and calibrate the instrument. You can also use
Fisher ValveLink software version 7.3 or higher to
setup, calibrate, and diagnose the valve and
instrument. For information on using ValveLink
software with the instrument refer to ValveLink
software help or documentation.
Do not install, operate, or maintain a DVC6000 digital
valve controller without being fully trained and qualified
in valve, actuator, and accessory installation,
operation, and maintenance. To avoid personal
injury or property damage, it is important to
carefully read, understand, and follow all of the
contents of this manual, including all safety
cautions and warnings. If you have any questions
about these instructions, contact your Emerson
Process Management sales office before proceeding.
ConventionsUsed in this Manual
Procedures that require the use of the 475 Field
Communicator have the Field Communicator symbol
in the heading.
Procedures that are accessible with the Hot Key
on the Field Communicator will also have the Hot Key
symbol in the heading.
Figure1-1. Sliding-Stem Control Valve with
FIELDVUE DVC6010 Digital Valve Controller
W7957 / IL
Some of the procedures also contain the sequence of
numeric keys required to display the desired Field
Communicator menu. For example, to access the
Setup Wizard, from the Online menu, press 1 (selects
Configure) followed by a second 1 (selects Basic
Setup) followed by a third 1 (selects Setup Wizard).
The key sequence in the procedure heading is shown
as (1-1-1). The path required to accomplish various
tasks, the sequence of steps through the Field
Communicator menus, is also presented in textual
format. Menu selections are shown in italics, e.g.,
Calibrate. An overview of the Field Communicator
menu trees are shown at the beginning of this manual.
1

Introduction and Specifications
September 2013 1-3
Figure 1-2. Rotary Control Valve with
FIELDVUE DVC6020 Digital Valve Controller
W9418
Note
475 Field Communicator menu
sequences used in this manual are for
instrument level HC, AD, PD, and ODV,
firmware 7 and above. Refer to the AC
menu tree at the beginning of this
manual for AC menu sequences.
These menu sequences are also
applicable to the 375 Field
Communicator.
Description
DVC6000 digital valve controllers (figures 1-1 and 1-2)
are communicating, microprocessor-based
current-to-pneumatic instruments. In addition to the
normal function of converting an input current signal to
a pneumatic output pressure, the DVC6000 digital
valve controller, using the HARTcommunications
protocol, gives easy access to information critical to
process operation. You can gain information from the
principal component of the process, the control valve
itself, using the Field Communicator at the valve, or at
a field junction box, or by using a personal computer
or operator’s console within the control room.
Using a personal computer and ValveLink software or
AMS Suite: Intelligent Device Manager, or a Field
Communicator, you can perform several operations
with the DVC6000 digital valve controller. You can
obtain general information concerning software
revision level, messages, tag, descriptor, and date.
Diagnostic information is available to aid you when
troubleshooting. Input and output configuration
parameters can be set, and the digital valve controller
can be calibrated. Refer to table 1-1 for details on the
capabilities of each diagnostic tier.
Using the HART protocol, information from the field
can be integrated into control systems or be received
on a single loop basis.
DVC6000 digital valve controllers are designed to
directly replace standard pneumatic and
electro-pneumatic valve mounted positioners.
Specifications
WARNING
Refer to table 1-2 for specifications.
Incorrect configuration of a
positioning instrument could result in
the malfunction of the product,
property damage or personal injury.
Specifications for DVC6000 digital valve controllers
are shown in table 1-2. Specifications for the Field
Communicator can be found in the product manual for
the Field Communicator.
Related Documents
Other documents containing information related to
DVC6000 digital valve controllers include:
Bulletin 62.1:DVC6000—Fisher FIELDVUE
DVC6000 Digital Valve Controllers (D102758X012)
Bulletin 62.1:DVC6000(S1)—Fisher FIELDVUE
DVC6000 Digital Valve Controller Dimensions
(D103308X012)
Fisher FIELDVUE DVC6000 Digital Valve
Controllers Quick Start Guide (D102762X012)
1

DVC6000 Digital Valve Controllers
September 2013
1-4
FIELDVUE Digital Valve Controller Split
Ranging −Supplement to HART Communicating
Fisher FIELDVUE Digital Valve Controller Instruction
Manuals (D103262X012)
Using FIELDVUE Instruments with the Smart
HART Loop Interface and Monitor (HIM) −
Supplement to HART Communicating Fisher
FIELDVUE Instrument Instruction Manuals
(D103263X012)
Using FIELDVUE Instruments with the Smart
Wireless THUMAdapter and a HART Interface
Module (HIM) −Supplement to HART Communicating
Fisher FIELDVUE Instrument Instruction Manuals
Audio Monitor for HART Communications −
Supplement to HART Communicating Fisher
FIELDVUE Instrument Instruction Manuals
(D103265X012)
HART Field Device Specification −Supplement
to Fisher FIELDVUE DVC6000 Digital Valve Controller
Instruction Manual (D103649X012)
Using the HART Tri-LoopHART -to-Analog
Signal Converter with FIELDVUE Digital Valve
Controllers −Supplement to HART Communicating
Fisher FIELDVUE Instrument Instruction Manuals
(D103267X012)
Hot Swap Procedure −Supplement to HART
Communicating Fisher FIELDVUE DVC5000
(Obsolete Product) and DVC6000 Digital Valve
Controllers Instruction Manuals (D103264X012)
Implementation of Lock-in-Last Strategy −
Supplement to Fisher FIELDVUE DVC6000 and
DVC6200 Digital Valve Controllers Instruction Manual
(D103261X012)
Fisher HF340 Filter Instruction Manual
(D102796X012)
ValveLink software help or documentation
Field Communicator User’s Manual
All documents are available from your Emerson
Process Management sales office. Also visit our
website at www.FIELDVUE.com.
EducationalServices
For information on available courses for DVC6000
digital valve controllers, as well as a variety of other
products, contact:
Emerson Process Management
Educational Services, Registration
P.O. Box 190; 301 S. 1st Ave.
Marshalltown, IA 50158-2823
Phone: [phone] or
Phone: [phone]
FAX: [phone]
e-mail: [email protected]
1

Introduction and Specifications
September 2013 1-5
Table 1-2. Specifications
Available Configurations
DVC6010: Sliding-stem applications
DVC6020: Rotary and long-stroke sliding-stem
applications [over 102 mm (4 inch) travel]
DVC6030: Quarter-turn rotary applications
Remote-Mounted Instrument(1)
DVC6005: Base unit for 2 inch pipestand or wall
mounting
DVC6015: Feedback unit for sliding-stem
applications
DVC6025: Feedback unit for rotary or long-stroke
sliding-stem applications
DVC6035: Feedback unit for quarter-turn rotary
applications
DVC6000 digital valve controllers can be mounted
on Fisher and other manufacturers rotary and
sliding-stem actuators.
Input Signal
Point-to-Point:
Analog Input Signal: 4-20 mA DC, nominal
Minimum Voltage Available at instrument terminals
must be 10.5 volts DC for analog control, 11 volts
DC for HART communication
Minimum Control Current: 4.0 mA
Minimum Current w/o Microprocessor Restart:
3.5 mA
Maximum Voltage: 30 volts DC
Overcurrent Protection: Input circuitry limits current
to prevent internal damage.
Reverse Polarity Protection: No damage occurs
from reversal of loop current.
Multi-drop:
Instrument Power: 11-30 volts DC at approximately
8 mA
Reverse Polarity Protection: No damage occurs
from reversal of loop current.
Output Signal
Pneumatic signal as required by the actuator, up to
full supply pressure.
Minimum Span: 0.4 bar (6 psig)
Maximum Span: 9.5 bar (140 psig)
Action: Double, Single direct, and Single reverse
Supply Pressure(2)
Recommended: 0.3 bar (5 psi) higher than
maximum actuator requirements, up to maximum
supply pressure
Maximum: 10 bar (145 psig) or maximum pressure
rating of the actuator, whichever is lower
Medium: Air or Natural Gas
Air: Supply pressure must be clean, dry air that
meets the requirements of ISA Standard 7.0.01.
Natural Gas: Natural gas must be clean, dry,
oil-free, and noncorrosive. H2S content should not
exceed 20 ppm.
A maximum 40 micrometer particle size in the air
system is acceptable. Further filtration down to 5
micrometer particle size is recommended. Lubricant
content is not to exceed 1 ppm weight (w/w) or
volume (v/v) basis. Condensation in the air supply
should be minimized
Steady-State Air Consumption(3)(4)
Standard Relay:
At 1.4 bar (20 psig) supply pressure: Less than 0.38
normal m3/hr (14 scfh)
At 5.5 bar (80 psig) supply pressure: Less than 1.3
normal m3/hr (49 scfh)
Low Bleed Relay:
At 1.4 bar (20 psig) supply pressure: Average value
0.056 normal m3/hr (2.1 scfh)
At 5.5 bar (80 psig) supply pressure: Average value
0.184 normal m3/hr (6.9 scfh)
Maximum Output Capacity(3)(4)
At 1.4 bar (20 psig) supply pressure: 10.0 normal
m3/hr (375 scfh)
At 5.5 bar (80 psig) supply pressure: 29.5 normal
m3/hr (1100 scfh)
Independent Linearity(5)
±0.50% of output span
Electromagnetic Compatibility
Meets EN 61326-1 (First Edition)
Immunity—Industrial locations per Table 2 of the
EN 61326-1 standard. Performance is shown
in table 1-3 below.
Emissions—Class A
ISM equipment rating: Group 1, Class A
Lightning and Surge Protection—The degree of
immunity to lightning is specified as Surge immunity
in table 1-3. For additional surge protection
commercially available transient protection devices
can be used.
-continued-
1

DVC6000 Digital Valve Controllers
September 2013
1-6
Table 1-2. Specifications (continued)
Vibration Testing Method
Tested per ANSI/ISA-S75.13.01 Section 5.3.5. A
resonant frequency search is performed on all three
axes. The instrument is subjected to the ISA
specified 1/2 hour endurance test at each major
resonance, plus an additional two million cycles.
Input Impedance
The input impedance of the DVC6000 active
electronic circuit is not purely resistive. For
comparison to resistive load specifications, an
equivalent impedance of 550 ohms may be used.
This value corresponds to 11V @ 20 mA.
Operating Ambient Temperature Limits(2)(6)
-40 to 85C (-40 to 185F) for most approved
valve-mounted instruments
-60 to 125C (-76 to 257F) for remote-mounted
feedback unit.
-52 to 85C (-62 to 185F) for valve-mounted
instruments utilizing the Extreme Temperature
option (fluorosilicone elastomers)
Humidity Limits
0 to 100% condensing relative humidity with
minimal zero or span shifts
Electrical Classification
Hazardous Area:
CSA—Intrinsically Safe, Explosion-proof,
Division 2, Dust Ignition-proof
FM—Intrinsically Safe, Explosion-proof,
Non-incendive, Dust Ignition-proof
ATEX—Intrinsically Safe, Flameproof, Type n
IECEx—Intrinsically Safe, Flameproof, Type n
Refer to tables 1-4, 1-5, 1-6, and 1-7, Hazardous
Areas Classifications and Special Instructions for
“Safe Use” and Installation in Hazardous Locations
in section 2, and Appendix B.
Pollution Degree 2, Overvoltage Category III per
ANSI/ISA-82.02.01 (IEC 61010-1 Mod).
Electrical Housing:
CSA—Type 4X, IP66
FM—Type 4X, IP66
ATEX—IP66
IECEx—IP66
Other Classifications/Certifications
Gas Certified, Single Seal Device—CSA, FM,
ATEX, and IECEx
FSETAN— Federal Service of Technological,
Ecological and Nuclear Inspectorate (Russia)
GOST-R— Russian GOST-R
INMETRO— National Institute of Metrology,
Quality, and Technology (Brazil)
KGS— Korea Gas Safety Corporation
(South Korea)
KISCO— Korea Industrial Safety Corporation
(South Korea)
NEPSI— National Supervision and Inspection
Centre for Explosion Protection and Safety of
Instrumentation (China)
PESO CCOE— Petroleum and Explosives Safety
Organisation −Chief Controller of Explosives (India)
TIIS— Technology Institution of Industrial Safety
(Japan)
Contact your Emerson Process Management sales
office for classification/certification specific
information
IEC 61010 Compliance Requirements
(Valve-Mounted Instruments only)
Power Source: The loop current must be derived
from a Separated Extra-Low Voltage (SELV) power
source.
Environmental Conditions: Installation Category I
Connections
Supply Pressure: 1/4 NPT internal and integral
pad for mounting 67CFR regulator
Output Pressure: 1/4 NPT internal
Tubing: 3/8-inch, recommended
Vent: 3/8 NPT internal
Electrical: 1/2 NPT internal conduit connection,
M20 adapter optional
-continued-
1

Introduction and Specifications
September 2013 1-7
Table 1-2. Specifications (continued)
Stem/Shaft Travel
Linear Actuators with rated travel between 6.35 mm
(0.25 inch) and 606 mm (23.375 inches)
Rotary Actuators with rated travel between 50
degrees and 180 degrees
Mounting(7)
Designed for direct actuator mounting or remote
pipestand or wall mounting. Mounting the
instrument vertically, with the vent at the bottom of
the assembly, or horizontally, with the vent pointing
down, is recommended to allow drainage of
moisture that may be introduced via the instrument
air supply.
Weight
Valve-Mounted Instruments
Aluminum: 3.5 kg (7.7 lbs)
Stainless Steel: 7.7 kg (17 lbs)
Remote-Mounted Instruments
DVC6005 Base Unit: 4.1 kg (9 lbs)
DVC6015 Feedback Unit: 1.3 kg (2.9 lbs)
DVC6025 Feedback Unit: 1.4 kg (3.1 lbs)
DVC6035 Feedback Unit: 0.9 kg (2.0 lbs)
Construction Materials
Housing, module base and terminal box:
A03600 low copper aluminum alloy
Cover: Thermoplastic polyester
Elastomers: Nitrile (standard)
Options
Supply and output pressure gauges or Tire
valves, Integral mounted filter regulator,
Stainless steel housing, module base and
terminal box Low bleed relay, Inline 10
micrometer air filter Safety Instrumented System
(SIS) Solutions Safety Related Nuclear
Applications Natural Gas Certified, Single Seal
Device Feedback Assembly PTFE Sleeve
Protective Kit for aluminum units in saltwater or
particulate environments
Declaration of SEP
Fisher Controls International LLC declares this
product to be in compliance with Article 3 paragraph
3 of the Pressure Equipment Directive (PED) 97 /
23 / EC. It was designed and manufactured in
accordance with Sound Engineering Practice (SEP)
and cannot bear the CE marking related to PED
compliance.
However, the product may bear the CE marking to
indicate compliance with other applicable European
Community Directives.
NOTE: Specialized instrument terms are defined in ISA Standard 51.1 - Process Instrument Terminology.
1. 3-conductor shielded cable, 22 AWG minimum wire size, is required for connection between base unit and feedback unit. Pneumatic tubing between base unit output connection and actuator
has been tested to 91 meters (300 feet). At 15 meters (50 feet) there was no performance degradation. At 91 meters there was minimal pneumatic lag.
2. The pressure/temperature limits in this document and any applicable code or standard should not be exceeded.
3. Values at 1.4 bar (20 psig) based on a single-acting direct relay; values at 5.5 bar (80 psig) based on double-acting relay.
4. Normal m3/hour - Normal cubic meters per hour at 0C and 1.01325 bar, absolute. Scfh - Standard cubic feet per hour at 60F and 14.7 psia
5. Typical Value. Not applicable for travels less than 19 mm (0.75 inch) or for shaft rotation less than 60 degrees. Also, not applicable to DVC6020 digital valve controllers in long-stroke
applications.
6. Temperature limits vary based on hazardous area approval.
7. Do not use the DVC6010S or DVC6020S in high vibration service where the mounting bracket uses standoffs (spacers) to mount to the actuator. Due to NAMUR mounting limitations, do
not use the DVC6030S in high vibration service.
Table1-3. EMC Summary Results—Immunity
Port Phenomenon Basic Standard Test Level Performance Criteria(1)
Point-to-
Point Mode Multi-drop Mode
Enclosure
Electrostatic discharge
(ESD) IEC 61000-4-2 4 kV contact
8 kV air A(2) A
Radiated EM field IEC 61000-4-3 80 to 1000 MHz @ 10V/m with 1 kHz AM at 80% 1400 to 2000 MHz @ 3V/m with 1 kHz AM at 80%
2000 to 2700 MHz @ 1V/m with 1 kHz AM at 80% A A
Rated power frequency
magnetic field IEC 61000-4-8 30 A/m at 50/60 Hz A A
I/O signal/control Burst IEC 61000-4-4 1 kV A(2) A
Surge IEC 61000-4-5 1 kV (line to ground only, each) B B
Conducted RF IEC 61000-4-6 150 kHz to 80 MHz at 3 Vrms A A
Performance Criteria:+/−1% effect.
1. A = No degradation during testing. B = Temporary degradation during testing, but is self-recovering.
2. Excluding auxiliary switch function, which meets Performance Criteria B.
1

DVC6000 Digital Valve Controllers
September 2013
1-8
Table 1-4. Hazardous Area Classifications—CSA (Canada)
Certification
Body Type Certification Obtained Entity Rating Temperature Code Enclosure Rating
CSA
DVC60x0
DVC60x0S
(x = 1,2,3)
Ex ia Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,E,
F,G per drawing GE42818
Natural Gas Approved
Vmax = 30 VDC
Imax = 226 mA
Ci = 5 nF
Li = 0.55 mH
Pi = 1.4 W
T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
Explosion-proof
Class I Division 1 GP B,C,D
Natural Gas Approved −−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
Class I Division 2 GP A,B,C,D
Class II Division 1 GP E,F,G
Class II Division 2 GP F,G
Class III
Natural Gas Approved
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
DVC6005
Ex ia Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,
E,F,G per drawing GE42818
Natural Gas Approved
Vmax = 30 VDC
Imax = 226 mA
Ci = 5 nF
Li = 0.55 mH
Pi = 1.4 W
Voc = 30 VDC
Isc = 12 mA
Ca = 66 nF
La = 246 mH
Po = 86 mW
T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
Explosion-proof
Class I Division 1 GP B,C,D
Natural Gas Approved −−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
Class I Division 2 GP A,B,C,D
Class II Division 1 GP E,F,G
Class II Division 2 GP F,G
Class III
Natural Gas Approved
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
DVC60x5
(x = 1,2,3)
Ex ia Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,
E,F,G per drawing GE42818
Vmax = 30 VDC
Imax = 100 mA
Ci = 0 uF
Li = 0 mH
Pmax = 160 mW
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) Type 4X, IP66
Explosion-proof
Class I Division 1 GP B,C,D −−−
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) Type 4X, IP66
Class I Division 2 GP A,B,C,D
Class II Division 1 GP E,F,G
Class II Division 2 GP F,G
Class III
−−−
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) Type 4X, IP66
1

Introduction and Specifications
September 2013 1-9
Table 1-5. Hazardous Area Classifications—FM (United States)
Certification
Body Type Certification Obtained Entity Rating Temperature Code Enclosure Rating
FM
DVC60x0
DVC60x0S
(x = 1,2,3)
IS Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,
E,F,G per drawing GE42819
Natural Gas Approved
Vmax = 30 VDC
Imax = 226 mA
Ci = 5 nF
Li = 0.55 mH
Pi = 1.4 W
T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
XP Explosion-proof
Class I Division 1 GP B,C,D
NI Non-incendive
Class I Division 2 GP A,B,C,D
DIP Dust Ignition-proof
Class II, III Division 1 GP E,F,G
S Suitable for Use
Class II, III Division 2 GP F,G
Natural Gas Approved
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
DVC6005
IS Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,E,
F,G per drawing GE42819
Natural Gas Approved
Vmax = 30 VDC
Imax = 226 mA
Ci = 5 nF
Li = 0.55 mH
Pi = 1.4 W
Voc = 9.6 VDC
Isc = 3.5 mA
Ca = 3.6 uF
La = 100 mH
Po = 8.4 mW
T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
XP Explosion-proof
Class I Division 1 GP B,C,D
NI Non-incendive
Class I Division 2 GP A,B,C,D
DIP Dust Ignition-proof
Class II, III Division 1 GP E,F,G
S Suitable for Use
Class II, III Division 2 GP F,G
Natural Gas Approved
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) Type 4X, IP66 Single Seal Device
DVC60x5
(x = 1,2,3)
IS Intrinsically Safe
Class I,II,III Division 1 GP A,B,C,D,
E,F,G per drawing GE42819
Vmax = 30 VDC
Imax = 100 mA
Ci = 0 uF
Li = 0 mH
Pi = 160 mW
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) Type 4X, IP66
XP Explosion-proof
Class I Division 1 GP A,B,C,D
NI Non-incendive
Class I Division 2 GP A,B,C,D
DIP Dust Ignition-proof
Class II, III Division 1 GP E,F,G
S Suitable for Use
Class II, III Division 2 GP F,G
−−−
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) Type 4X, IP66
1

DVC6000 Digital Valve Controllers
September 2013
1-10
Table 1-6. Hazardous Area Classifications—ATEX
Certificate Type Certification Obtained Entity Rating Temperature Code Enclosure
Rating
ATEX
DVC60x0
DVC60x0S
(x = 1,2,3)
II 1 G & D
Intrinsically Safe
Gas
Ex ia IIC T5/T6 Ga
Dust
Ex ia IIIC T85C (Ta ≤+73C), T92C
(Ta ≤+80C) Da
Per drawing GE60771
Natural Gas Approved
Ui= 30 VDC
Ii= 226 mA
Ci= 5 nF
Li= 0.55 mH
Pi= 1.4 W
T5(Tamb ≤80C)
T6(Tamb ≤75C) IP66
Single Seal Device
II 2 G
Flameproof
Gas
Ex d IIC T5/T6 Gb
Natural Gas Approved
−−−T5(Tamb ≤85C)
T6(Tamb ≤80C) IP66
Single Seal Device
II 3 G
Type n
Gas
Ex nC IIC T5/T6 Gc
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) IP66 Single Seal Device
DVC6005
II 1 G & D
Intrinsically Safe
Gas
Ex ia IIC T5/T6 Ga
Dust
Ex ia IIIC T85C (Ta ≤+76C), T89C
Ta ≤+80C) Da
Per drawing GE60771
Natural Gas Approved
Ui = 30 VDC
Ii = 226 mA
Ci = 5 nF
Li = 0.55 mH
Pi = 1.4 W
Uo = 9.6 VDC
Io = 3.5 mA
Co = 3.6 uF
Lo = 100 mH
Po = 8.4 mW
T5(Tamb ≤80C)
T6(Tamb ≤75C) IP66 Single Seal Device
II 2 G
Flameproof
Gas
Ex d IIC T5/T6 Gb
Natural Gas Approved
−−−T5(Tamb ≤85C)
T6(Tamb ≤80C) IP66
Single Seal Device
II 3 G
Type n
Gas
Ex nC IIC T5/T6 Gc
−−−T5(Tamb ≤80C)
T6(Tamb ≤75C) IP66 Single Seal Device
DVC60x5
(x = 1,2,3)
II 1 G & D
Intrinsically Safe
Gas
Ex ia IIC T4/T5/T6 Ga
Dust
Ex ia IIIC T85C (Tamb ≤+64C) T100C
(Tamb ≤+79C), T135C (Tamb ≤+114C)
T146C (Tamb ≤+125C) Da
Per drawing GE60771
Ui = 30 VDC
Ii = 100 mA
Ci = 0 uF
Li = 0 mH
Pi = 160 mW
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) IP66
II 2 G
Flameproof
Gas
Ex d IIC T4/T5/T6 Gb
−−−
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) IP66
II 3 G
Type n
Gas
Ex nA IIC T4/T5/T6 Gc
−−−
T4(Tamb ≤125C)
T5(Tamb ≤95C)
T6(Tamb ≤80C) IP66
1