Emerson Rosemount 3051 User manual

Reference Manual
00809-0100-4797, Rev DA
August 2016
Rosemount™3051 Pressure Transmitter
with PROFIBUS®PA Protocol

iii
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
1Section 1: Introduction
1.1 Using this manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.2 Models covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.3 Device revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.4 Transmitter overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.5 Product recycling/disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
2Section 2: Configuration
2.1 Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2.3 Hazardous locations certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4 Configuration guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2.4.1 Profile 3.02 identification number adaptation mode . . . . . . . . . . . . . . . . . 4
2.4.2 Block modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.4.3 Configuration tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5 Basic setup tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.5.1 Assign address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5.2 Pressure configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.6 Detailed setup tasks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.6.1 Flow configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.6.2 Level configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.6.3 Damping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6.4 Process alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6.5 LCD display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.6.6 Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.6.7 LOI security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.6.8 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3Section 3: Hardware Installation
3.1 Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.3 Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.3.1 Mechanical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.3.2 Environmental considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Contents

iv
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
3.4 Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.4.1 Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.4.2 Impulse piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
3.4.3 Process connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.4.4 In-line process connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.5 Rosemount 305, 306 and 304 Manifolds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
3.5.1 Rosemount 305 Integral Manifold installation procedure . . . . . . . . . . . .23
3.5.2 Rosemount 306 Integral Manifold installation procedure . . . . . . . . . . . .24
3.5.3 Rosemount 304 Conventional Manifold installation procedure . . . . . . .24
3.5.4 Manifold operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.6 Liquid level measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.6.1 Open vessels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3.6.2 Closed vessels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4Section 4: Electrical Installation
4.1 Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
4.3 LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
4.4 LCD display with local operator interface (LOI). . . . . . . . . . . . . . . . . . . . . . . . . . . .34
4.5 Configure security and simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
4.5.1 Security (write protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.5.2 Simulate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.6 Electrical considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.6.1 Conduit installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4.6.2 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
4.6.3 Signal wiring grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
4.6.4 Transient protection terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
4.6.5 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5Section 5: Calibration
5.1 Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
5.3 Calibration overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
5.3.1 Zero trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
5.3.2 Sensor trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
5.3.3 Recall factory trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.4 Determining calibration frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
5.5 Zero trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

v
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
5.6 Sensor trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
5.7 Recall factory trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
5.8 Compensating for line pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
5.8.1 Range 2 and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
5.8.2 Range 4 and Range 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
6Section 6: Troubleshooting
6.1 Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
6.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
6.3 Service support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
6.4 Diagnostics identification and recommended action . . . . . . . . . . . . . . . . . . . . . .48
6.4.1 Extended diagnostics identification with class one master. . . . . . . . . . . .49
6.5 PlantWeb™and NE107 diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
6.6 Alert messages and fail safe type selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
6.7 Disassembly procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
6.7.1 Remove from service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.7.2 Remove terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
6.7.3 Remove the electronics board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6.7.4 Remove the sensor module from the electronics housing . . . . . . . . . . . .54
6.8 Reassembly procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
6.8.1 Attach the electronics board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.8.2 Install the terminal block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.8.3 Reassemble the Rosemount 3051C process flange . . . . . . . . . . . . . . . . . .55
6.8.4 Install the drain/vent valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
AAppendix A: Specifications and Reference Data
A.1 Performance specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
A.1.1 Conformance to specification (±3s [Sigma]) . . . . . . . . . . . . . . . . . . . . . . . .57
A.1.2 Reference accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
A.1.3 Flow performance - flow reference accuracy. . . . . . . . . . . . . . . . . . . . . . . . 58
A.1.4 Total performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
A.1.5 Long term stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
A.1.6 Dynamic performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
A.1.7 Line pressure effect per 1000 psi (68,95 bar) . . . . . . . . . . . . . . . . . . . . . . . 59
A.1.8 Ambient temperature effect per 50 °F (28 °C). . . . . . . . . . . . . . . . . . . . . . . 59
A.1.9 Mounting position effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
A.1.10 Vibration effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
A.1.11 Power supply effect. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

vi
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
A.1.12 Electromagnetic compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
A.1.13 Transient protection (option code T1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
A.2 Functional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
A.2.1 Range and sensor limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
A.2.2 4–20 mA HART (output code A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
A.2.3 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
A.2.4 Foundation Fieldbus (output code F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
A.2.5 PROFIBUS PA (output code W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.2.6 Wireless (output code X). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A.2.7 Low Power output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
A.2.8 Overpressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
A.2.9 Static pressure limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
A.2.10 Burst pressure limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
A.2.11 Failure mode alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
A.2.12 Temperature limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
A.2.13 Humidity limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.2.14 Turn-on time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.2.15 Volumetric displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.2.16 Damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.3 Physical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.3.1 Material selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.3.2 Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.3.3 Process connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
A.3.4 Process-wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
A.3.5 Rosemount 3051L process wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
A.3.6 Non-wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
A.3.7 Shipping weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
A.4 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
A.4.1 Standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
A.4.2 Custom configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
A.4.3 Tagging (3 options available) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.4 Commissioning Tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
A.4.5 Optional Rosemount 304, 305 or 306 integral manifolds. . . . . . . . . . . . . 69
A.4.6 Other seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.7 Output information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.8 Display and interface options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.9 Configuration buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
A.4.10 Transient protection (option code T1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

vii
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
A.4.11 Bolts for flanges and adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.12 Conduit plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
A.4.13 Rosemount 3051C coplanar flange and Rosemount 3051T bracket
option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
A.4.14 Rosemount 3051C traditional flange bracket options . . . . . . . . . . . . . . .70
A.5 Range limits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
A.6 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
A.7 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
A.8 Pipe I.D. range codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
A.9 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
BAppendix B: Product Certifications
B.1 Rosemount™3051 Pressure Transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1.1 European Directive Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
B.1.2 Ordinary Location Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
B.1.3 North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
B.1.4 Europe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
B.1.5 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .141
B.1.6 Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
B.1.7 China . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
B.1.8 Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
B.1.9 Technical Regulations Customs Union (EAC). . . . . . . . . . . . . . . . . . . . . . .144
B.1.10 Combinations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
B.1.11 Conduit plugs and adapters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
B.1.12 Additional certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
B.2 Rosemount 3051 Wireless Pressure Transmitter . . . . . . . . . . . . . . . . . . . . . . . . 146
B.2.1 European Directive Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.2 Telecommunication Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.3 FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.4 Ordinary Location Certification for FM . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.5 U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.6 Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.7 Europe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146
B.2.8 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
B.2.9 Brazil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
B.2.10 China . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
B.2.11 EAC – Belarus, Kazakhstan, Russia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
B.2.12 Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147
B.3 Approval drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148

viii
Reference Manual
00809-0100-4797, Rev DA
Table of Contents
August 2016
Table of Contents
CAppendix C: Local Operator Interface (LOI) Menu
C.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
C.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
C.2.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .175
DAppendix D: PROFIBUS®Block Information
D.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
D.2 Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
D.3 PROFIBUS block parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
D.4 Condensed status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185

ix
Reference Manual
00809-0100-4797, Rev DA
Title Page
August 2016
Title Page
Rosemount™3051 Pressure
Transmitter
NOTICE
Read this manual before working with the product. For personal and system safety, and
for optimum product performance, make sure you thoroughly understand the
contents before installing, using, or maintaining this product.
For technical assistance, contacts are listed below:
Customer Central
Technical support, quoting, and order-related questions.
United States - 1-800-999-9307 (7:00 am to 7:00 pm CST)
Asia Pacific- 65 777 8211
Europe/ Middle East/ Africa - 49 (8153) 9390
North American Response Center
Equipment service needs.
1-800-654-7768 (24 hours—includes Canada)
Outside of these areas, contact your local Emerson™Process Management
representative.
The products described in this document are NOT designed for nuclear-qualified
applications. Using non-nuclear qualified products in applications that require
nuclear-qualified hardware or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Emerson
Process Management Sales Representative.
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with
the appropriate local, national, and international standards, codes, and practices.
Review the approvals section of this Reference Manual for any restrictions associated
with a safe installation.
In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers
when power is applied to the unit.
Process leaks may cause harm or result in death.
Install and tighten process connectors before applying pressure.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on
leads can cause electrical shock.

x
Reference Manual
00809-0100-4797, Rev DA
Title Page
August 2016
Title Page

1
Reference Manual
00809-0100-4797, Rev DA
Introduction
August 2016
Introduction
Section 1 Introduction
1.1 Using this manual
The sections in this manual provide information on installing, operating, and maintaining
the Rosemount™3051Pressure Transmitter with PROFIBUS®PA Protocol. The sections are
organized as follows:
Section 2: Configuration provides instruction on commissioning and operating Rosemount
3051 Transmitters. Information on software functions, configuration parameters, and
online variables is also included.
Section 3: Hardware Installation contains mechanical installation instructions, and field
upgrade options.
Section 4: Electrical Installation contains electrical installation instructions, and field
upgrade options.
Section 5: Calibration contains operation and maintenance techniques.
Section 6: Troubleshooting provides troubleshooting techniques for the most common
operating problems.
Appendix A: Specifications and Reference Data supplies reference and specification data, as
well as ordering information.
Appendix B: Product Certifications contains intrinsic safety approval information, European
ATEX directive information, and approval drawings.
Appendix C: Local Operator Interface (LOI) Menu contains the complete local operator
interface menu.
Appendix D: PROFIBUS® Block Information contains PROFIBUS block and parameter
information.
1.2 Models covered
The following Rosemount 3051 Pressure Transmitters are covered by this manual:
Rosemount 3051C Coplanar™Pressure Transmitter
Rosemount 3051CD Differential Pressure Transmitter
– Measures differential pressure up to 2000 psi (137,9 bar)
Rosemount 3051CG Gage Pressure Transmitter
– Measures gage pressure up to 2000 psi (137,9 bar)
Rosemount 3051CA Absolute Pressure Transmitter
– Measures absolute pressure up to 4000 psia (275,8 bar)
Rosemount 3051T In-Line Pressure Transmitter

2
Reference Manual
00809-0100-4797, Rev DA
Introduction
August 2016
Introduction
Rosemount 3051T Gage and Absolute Pressure Transmitter
– Measures gage pressure up to 10000 psi (689,5 bar)
Rosemount 3051L Liquid Level Transmitter
– Provides precise level and specific gravity measurements up to 300 psi (20,7 bar) for a
wide variety of tank configurations
Note
For Rosemount 3051 with HART®Protocol, see Rosemount 3051 Reference Manual.
For Rosemount 3051 with FOUNDATION™Fieldbus, see Rosemount 3051 Reference Manual.
1.3 Device revisions
1.4 Transmitter overview
The Rosemount 3051C Coplanar design is offered for differential pressure (DP), gage
pressure (GP), and absolute pressure (AP) measurements. The Rosemount 3051C utilizes
Emerson Process Management capacitance sensor technology for DP and GP
measurements. Piezoresistive sensor technology is utilized in the Rosemount 3051T and
3051CA measurements.
The major components of the Rosemount 3051 are the sensor module and the electronics
housing. The sensor module contains the oil filled sensor system (isolating diaphragms, oil
fill system, and sensor) and the sensor electronics. The sensor electronics are installed
within the sensor module and include a temperature sensor (RTD), a memory module, and
the capacitance to digital signal converter (C/D converter). The electrical signals from the
sensor module are transmitted to the output electronics in the electronics housing. The
electronics housing contains the output electronics board, the optional local operator
interface (LOI) buttons, and the terminal block.
For the Rosemount 3051C design pressure is applied to the isolating diaphragms, the oil
deflects the center diaphragm, which then changes the capacitance. This capacitance signal
is then changed to a digital signal in the C/D converter. The microprocessor then takes the
signals from the RTD and C/D converter calculates the correct output of the transmitter.
1.5 Product recycling/disposal
Recycling of equipment and packaging should be taken into consideration and disposed of
in accordance with local and national legislation/regulations.
Table 1-1. Device Revisions
Date Software
revision
PROFIBUS
profile
Changesto
software Compatible files Manual revision
08/10 2.5.0 [1...1] 3.02 New product
3051 GSD: rmt4444.gsd
Profile 3.02 GSD: pa139700.gsd
DD: ROPA3__TP_3051.ddl
DTM: Pressure_PROFIBUS_3.02_DTM_v1.0.8.exe
DA

3
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
Section 2 Configuration
Section overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Hazardous locations certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Configuration guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
Basic setup tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Detailed setup tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
2.1 Section overview
This section contains information on commissioning the Rosemount™3051Pressure
Transmitter with PROFIBUS®PA Protocol using either the local operator interface (LOI) or
class two master.
2.2 Safety messages
Procedures and instructions in this section may require special precautions to ensure the
safety of the personnel performing the operations. Information that raises potential safety
issues is indicated by a warning symbol ( ). Refer to the following safety messages before
performing an operation preceded by this symbol.
Explosions could result in death or serious injury.
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Review the
approvals section of this Reference Manual for any restrictions associated with a safe
installation.
In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers
when power is applied to the unit.
Process leaks may cause harm or result in death.
Install and tighten process connectors before applying pressure.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.

4
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
Figure 2-1. Commissioning and Installation Flowchart
2.3 Hazardous locations certifications
Individual transmitters are clearly marked with a tag indicating the approvals they carry.
Transmitters must be installed in accordance with all applicable codes and standards to
maintain these certified ratings. Refer to “Product Certifications” on page 139 for
information on these approvals.
2.4 Configuration guidelines
The Rosemount 3051 can be configured either before or after installation. Configuring the
transmitter on the bench using the LOI or class two master ensures that all transmitter
components are in working order prior to installation.
To configure on the bench, required equipment includes a power supply, an LOI (option M4)
or a class two master with DP/PA coupler, proper cable and terminators.
Verify the Security hardware jumper is set to the OFF position in order to proceed with
configuration. See Figure 4-2 for jumper location.
2.4.1 Profile 3.02 identification number adaptation mode
Rosemount 3051 PROFIBUS Profile 3.02 devices are set to Identification Number
Adaptation mode (0127) when shipped from the factory. This mode allows the transmitter
to communicate with any PROFIBUS class one master with either the generic Profile GSD
(9700) or Rosemount 3051 specific GSD (4444).
2.4.2 Block modes
When configuring a device with the LOI, the output status will change to Good – Function
Check to alert hosts that the transmitter is not in standard operation mode.
Congure Verify Install
UNITS
Section 2
OUTPUT
Section 2
PROTOCOL SPECIFIC
INFORMATION
(if applicable)
Section 2
TRANSMITTER
PARAMETERS
Section 2
PRESSURE SENSOR
Section 2
TRANSMITTER
Section 3
WIRING
Section 4
ELECTRONIC
HARDWARE
SETTINGS
Section 4
SENSOR TRIM
Section 5
yes
CALIBRATION
Section 5
no
WITHIN
SPECIFICATIONS
?

5
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
When configuring a device with a class two master, blocks must be set to Out of Service
(OOS) to download parameters that could affect the output. This prevents the class one
master from seeing a jump in output without a status change. Setting the blocks OOS and
back into Auto might be done automatically using the class two master when using the
Rosemount 3051 DD or DTM™, if no additional action is required when configuring the
device. Verify the block mode is set back to Auto.
2.4.3 Configuration tools
The Rosemount 3051 can be configured using two tools: LOI and/or class two master.
The LOI requires option code M4 to be ordered. To activate the LOI, push either
configuration button located under the top tag of the transmitter. See Table 2-1 and
Figure 2-2 for operation and menu information. See Appendix D: PROFIBUS® Block
Information for a complete LOI menu tree.
Class two masters require either DD or DTM files for configuration. These files can be found
at EmersonProcess.com/Rosemount or by contacting your local Emerson Process represen-
tative. Some configurations steps may need to be completed in offline mode or using the
LOI.
The remainder of this section covers the configuration tasks using the applicable
configuration tool.
Note
Instructions in this section use the language found in the class two master or LOI. See
Appendix D: PROFIBUS® Block Information to cross reference parameters between the class
two master, LOI and PROFIBUS specification.
2.5 Basic setup tasks
The following tasks are recommended for initial configuration of the Rosemount 3051
PROFIBUS Device.
2.5.1 Assign address
The Rosemount 3051 is shipped with a temporary address of 126. This must be changed to
a unique value between 0 and 125 in order to establish communication with the class one
master. Usually, addresses 0–2 are reserved for masters, therefore transmitter addresses
between 3 and 125 are recommended for the device.
Address can be set using either:
LOI – see Table 2-1 and Figure 2-2
Class two master – see respective class two master manual for setting instrument
addresses
2.5.2 Pressure configuration
The Rosemount 3051 ships with the following settings:
Measurement type: Pressure
Engineering units: Inches H2O
Linearization: None
Scaling: None

6
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
Each of these parameters can be set using,
LOI – see Table 2-1 and Figure 2-2
Class two master – see Pressure configuration using class two master
Pressure unit parameters
The LOI was designed to automatically set the following parameters when selecting a
Pressure Unit:
Measurement type: Pressure
Linearization: None
Scaling: None
See Flow or Level Configuration for defaults when configuring with the LOI.
Figure 2-2. LOI Menu
Note
See Appendix C: Local Operator Interface (LOI) Menu for a more detailed LOI menu and unit
list.
Pressure configuration using class two master
1. From the Basic Setup >> Units >> Primary Value >> Primary Value Type dropdown, select
Pressure.(1)
2. Select units.
Note
Pressure units in steps 2a, 2b, and 2c must match. Set units in the Al Block in offline mode or
using the LOI.
Table 2-1. LOI Operation
Button Action Navigation Character entry Save?
Scroll Moves down menu
categories
Changes character
value(1)
1. Characters flash when they can be changed.
Changes between Save
and Cancel
Enter Select menu category Enters character and
advances Saves
1. Measurement Type Pressure drives Linearization to None (Characterization >> Characterization Type >> No linearization) when down-
loaded to the device. Re-upload configuration to verify new Characterization Type.
6. IDENTIFICATION #
5. DISPLAY
4. DAMPING
3. UNITS
2. CALIBRATION
1. ADDRESS
7. EXIT
1 - 126
RESET FACTORY
UPPER SENSOR
LOWER SENSOR
ZERO
TEMPERATURE
LEVEL
FLOW
PRESSURE
ENTER into menu
SCROLL down list

7
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
a. From the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) >> Unit
(Secondary Value 1) dropdown, select engineering unit.
b. From the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) >> Unit
(PV) dropdown, select engineering unit.
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >> Unit (Output)
dropdown, select engineering unit.
3. Enter scaling.
Note
Scaling is done in the Transducer Block. No scaling required for pressure measurement.
a. In the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2a).
b. In the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2b).
4. Verify Analog Input (AI) Block.
Note
Scaling should not be repeated in the Al Block. Configure the Al Block in offline mode or
using the LOI.
a. In the Basic Setup >> Units >> Process Value Scale (Analog Input Block) field, enter upper
and lower values (this value should correspond to the unit selected in step 2b).
b. In the Basic Setup >> Units >> Output Signal (Analog Input Block) field, enter upper and
lower values (this value should correspond to the unit selected in step 2c).
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >>
Characterization Type dropdown, select No Linearization.
2.6 Detailed setup tasks
The following tasks explain how to configure the Rosemount 3051 for Flow or Level
measurement and how to configure additional parameters found in the device.
2.6.1 Flow configuration
LOI
To configure the Rosemount 3051 for Flow measurement with the LOI, select UNITS >>
FLOW. When configuring Flow units, the following parameters are set:
Measurement type: Flow
Linearization: Square Root
During unit configuration, the user defines scaling, units and low flow cutoff per the
application requirements. See Appendix D: PROFIBUS® Block Information for detailed
menu for further scaling help.

8
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
Note
The LOI assumes a zero based scaling (minimum pressure = minimum flow = zero) for Flow
applications in order to improve configuration efficiency. Class two masters can be used if
non-zero based scaling is required. Low flow cutoff has a default value of 5.0%. Low Flow
cutoff can be set to 0% if required.
Class two master
To configure the transmitter for a flow application, use the flow output in the Transducer
Block.
Flow configuration using class two master
1. From the Basic Setup >> Units >> Primary Value >> Primary Value Type dropdown, select
Flow.(1)
2. Select units.
Note
Flow units in steps 2a, 2b and 2c must match. Set units in the Al Block in offline mode or
using the LOI.
a. From the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) >> Unit
(Secondary Value 1) dropdown, select engineering unit.
b. From the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) >> Unit
(PV) dropdown, select engineering unit.
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >> Unit (Output)
dropdown, select engineering unit.
3. Enter scaling.
Note
Scaling is done in the Transducer Block.
a. In the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2a).
b. In the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2b).
4. Verify Analog Input (AI) Block.
Note
Scaling should always be done in the Transducer Block. Ensure the Al Block is always set to
no linearization for flow applications. To ensure no additional scaling is being done on the Al
Block, set the lower values in steps 4a and 4b to 0 and the upper values to 100.
a. In the Basic Setup >> Units >> Process Value Scale (Analog Input Block) field, enter upper
and lower values (this value should correspond to the unit selected in step 2b).
1. Measurement Type Flow drives Linearization to Square Root in the Transducer Block (Characterization > Characterization Type > Square
Root) when downloaded to the device. Re-upload configuration to verify new Characterization Type. Al Block should always be set to no
linearization for flow applications.

9
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
b. In the Basic Setup >> Units >> Output Signal (Analog Input Block) field, enter upper and
lower values (this value should correspond to the unit selected in Step 2c).
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >>
Characterization Type dropdown, select No Linearization.
5. Cycle power after configuration is complete.
6. Verify all parameters have written to the device correctly.
2.6.2 Level configuration
LOI
To configure the Rosemount 3051 for Level measurement with the LOI, select UNITS >>
LEVEL. When configuring Level units, the following parameters are set:
Measurement type: Level
Linearization: None
During unit configuration, the user defines scaling and units per the application
requirements. See Appendix D: PROFIBUS® Block Information for detailed menu for further
scaling help.
Class two master
To configure the transmitter for a level application, use the level output in the Transducer
Block.
Level configuration using class two master
1. From the Basic Setup >> Units >> Primary Value >> Primary Value Type dropdown, select
Level.(1)
2. Select units.
Note
Level units in steps 2a, 2b, and 2c must match. Set units in the Al Block in offline mode or
using the LOI.
a. From the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) >> Unit
(Secondary Value 1) dropdown, select engineering unit.
b. From the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) >> Unit
(PV) dropdown, select engineering unit.
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >> Unit (Output)
dropdown, select engineering unit.
3. Enter scaling.
Note
Scaling is done in the Transducer Block.
a. In the Basic Setup >> Units >> Primary Value >> Scale In (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2a).
1. Measurement Type Level drives Linearization to None (Characterization > Characterization Type > No Linearization) when downloaded
to the device. Re-upload configuration to verify new Characterization Type.

10
Reference Manual
00809-0100-4797, Rev DA
Configuration
August 2016
Configuration
b. In the Basic Setup >> Units >> Primary Value >> Scale Out (Transducer Block) field,
enter upper and lower values (this value should correspond to the unit selected in
step 2b).
4. Verify Analog Input (AI) Block.
Note
Scaling should not be repeated in the Al Block. Configure the Al Block in offline mode or
using the LOI. To ensure no additional scaling is being done on the Al Block, set the lower
values in steps 4a and 4b to 0 and the upper values to 100.
a. In the Basic Setup >> Units >> Process Value Scale (Analog Input Block) field, enter upper
and lower values (this value should correspond to the unit selected in step 2b).
b. In the Basic Setup >> Units >> Output Signal (Analog Input Block) field, enter upper and
lower values (this value should correspond to the unit selected in step 2c).
c. From the Basic Setup >> Units >> Output Signal (Analog Input Block) >>
Characterization Type dropdown, select No Linearization.
5. Cycle power after configuration is complete.
6. Verify all parameters have written to the device correctly.
2.6.3 Damping
User-selected damping will affect the transmitters ability to respond to changes in the
applied process. The Rosemount 3051 has a default damping value of 0.0 seconds applied
in the analog input (AI) block.
Damping can be set using,
LOI – see Table 2-1 and Figure 2-2
Class two master – see Damping configuration using class two master
Damping configuration using class two master
Note
Configure damping in offline mode or using the LOI.
1. In the Basic Setup >> Damping >> Filter Time Const field, enter value (in seconds).
2. Cycle power after configuration is complete.
3. Verify all parameters have written to the device correctly.
2.6.4 Process alerts
Process alerts activate an output alert status when the configured alert point is exceeded. A
process alert will be transmitted continuously if the output set points are exceeded. The
alert will reset once the value returns within range.
Process Alert parameters are defined as follows
Upper alarm: Changes Output Status to Good – Critical Alarm – Hi Limit
Upper warning: Changes Output Status to Good – Advisory Alarm – Hi Limit
Lower warning: Changes Output Status to Good – Advisory Alarm – Lo Limit
Lower alarm: Changes Output Status to Good – Critical Alarm – Lo Limit
Alarm hysteresis: Amount the output value must pass back into range before alarm is
cleared.