Emerson Rosemount User manual

Reference Manual
00809-0100-4021, Rev GC
April 2014
Rosemount®3144P Temperature Transmitter

Reference Manual
00809-0100-4021, Rev GC
Title Page
April 2014
iii
Rosemount®3144P Temperature
Transmitter
NOTICE
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
Within the United States, Emerson Process Management has two toll-free assistance
numbers:
Customer Central
Technical support, quoting, and order-related questions.
1-800-999-9307 (7:00 am to 7:00 pm CST)
North American Response Center
Equipment service needs.
1-800-654-7768 (24 hours)
International
(952)-906-8888
The products described in this document are NOT designed for nuclear-qualified
applications. Using non-nuclear qualified products in applications that require
nuclear-qualified hardware or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Emerson
Process Management Sales Representative.

iv
Reference Manual
00809-0100-4021, Rev GC
Title Page
April 2014

v
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents
1Section 1: Introduction
1.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1.1 Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.1.2 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.2 Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2.2 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2.3 Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.2.4 Moist or corrosive environments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.2.5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.2.6 Software compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3 Return of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.4 3144P revisions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.5 Confirm HART revision capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2Section 2: Installation
2.1 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.2 Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.2.1 Setting the loop to manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.2.2 Set the switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.3 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.4 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.4.1 Typical North American installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.4.2 Typical European installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.4.3 In conjunction with a Rosemount 333 HART Tri-Loop™
(HART / 4–20 mA only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.4.4 LCD display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.4.5 Multichannel installation (HART / 4–20 mA only). . . . . . . . . . . . . . . . . . . . .20
2.5 Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.5.1 HART / 4–20 mA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
2.5.2 Foundation fieldbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.5.3 Sensor connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.6 Power supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2.6.1 Surges/transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
2.6.2 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Table of Contents

vi
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents
3Section 3: HART®commissioning
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.2 Confirm HART revision capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.3 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3.4 Field communicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3.4.1 Updating the HART communication software . . . . . . . . . . . . . . . . . . . . . . .30
3.4.2 Device dashboard menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3.4.3 Device dashboard Fast Key sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
3.5 Review configuration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.5.1 Review. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.6 Check output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.6.1 Analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.7 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.7.1 Variable mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.7.2 Sensor configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.7.3 Change type and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.7.4 Output units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
3.7.5 Sensor 1 serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
3.7.6 Sensor 2 serial number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
3.7.7 2-wire RTD offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
3.7.8 Terminal (body) temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
3.7.9 Dual-sensor configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
3.8 Device output configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
3.8.1 PV range values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
3.8.2 Process variable damping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
3.8.3 Alarm and saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
3.8.4 HART output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
3.8.5 LCD display options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
3.9 Device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
3.9.1 Tag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
3.9.2 Long tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
3.9.3 Date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
3.9.4 Descriptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
3.9.5 Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
3.10Measurement filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
3.10.150/60 Hz filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
3.10.2Master reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96

vii
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents
3.10.3Intermittent sensor detect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
3.10.4Intermittent threshold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
3.10.5Open sensor holdoff. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
3.11Diagnostics and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
3.11.1Loop test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
3.12Multidrop communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
3.13Use with the HART Tri-Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
3.14Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.14.1Calibration frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.15Trim the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
3.15.1Sensor input trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
3.15.2Active calibrator and EMF compensation. . . . . . . . . . . . . . . . . . . . . . . . . . 124
3.15.3Transmitter-sensor matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
3.15.4D/A output trim or scaled output trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
3.15.5Output trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
3.15.6Scaled output trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
3.16Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
3.16.1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
3.16.2LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
3.16.3Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
4Section 4: Foundation™ fieldbus configuration
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
4.3 General block information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
4.3.1 Device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
4.3.2 Node address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
4.3.3 Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
4.3.4 Link Active Scheduler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
4.3.5 Capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
4.4 Foundation fieldbus function blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
4.5 Resource block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
4.5.1 Features and Features_Sel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
4.5.2 PlantWeb™alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
4.5.3 Recommended actions for PlantWeb alerts . . . . . . . . . . . . . . . . . . . . . . . 148
4.5.4 Recommended actions for field diagnostics per NE107 . . . . . . . . . . . . . 149
4.5.5 Resource block diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
4.6 Sensor transducer block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
4.6.1 Sensor transducer block diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

viii
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents
4.7 LCD display transducer block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
4.7.1 Custom meter configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
4.7.2 LCD display transducer block diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . 153
4.8 Hot Backup™transducer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
4.9 Analog Input (AI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
4.9.1 Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
4.9.2 Configure the AI block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
4.9.3 Filtering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
4.9.4 Process alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
4.9.5 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
4.9.6 Advanced features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
4.9.7 Analog input diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
4.10Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
4.10.1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
4.10.2Trim the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
4.10.3Advanced diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
4.10.4Statistical process monitoring (SPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
4.10.5SPM configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
4.11Troubleshooting guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
4.11.1Foundation fieldbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
4.11.2LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
5Section 5: Maintenance
5.1 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
5.2 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
5.2.1 Test terminal (HART / 4–20 mA only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
5.2.2 Sensor checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
5.2.3 Electronics housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
5.2.4 Transmitter diagnostics logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
6Section 6: Certified safety instrumented system (safety-
certified)
6.1 Safety instrumented systems (SIS) certification. . . . . . . . . . . . . . . . . . . . . . . . . . 179
6.2 Rosemount®3144P safety certified identification . . . . . . . . . . . . . . . . . . . . . . . 179
6.3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
6.4 Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
6.5 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180

ix
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents
6.6 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
6.7 Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.8 3144P safety-certified identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.9 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.10Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.11Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
6.12Operation and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
6.12.1Proof test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
6.12.2Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
6.13Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
6.13.1Failure rate data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
6.13.2Product life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
6.14Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
7Section 7: Prior use (PU) safety instrumented system
7.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
7.2 Safe failure fraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.3 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.3.1 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.3.2 Changing switch position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 188
7.3.3 Proof test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190
AAppendix A: Reference data
A.1 HART® and Foundation™ fieldbus specifications . . . . . . . . . . . . . . . . . . . . . . . . 191
A.1.1 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
A.1.2 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
A.1.3 Performance specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
A.2 HART / 4–20 mA specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
A.3 Foundation fieldbus specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
A.4 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
A.5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
A.6 Spare parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
BAppendix B: Product Certifications
B.1 Approved Manufacturing Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
B.2 European Directive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
B.3 Ordinary Location Certification from FM Approvals . . . . . . . . . . . . . . . . . . . . . . 217

x
Reference Manual
00809-0100-4021, Rev GC
Table of Contents
April 2014
Table of Contents

Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
1
Introduction
Section 1 Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Return of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
3144P revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 6
Confirm HART revision capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
1.1 Overview
1.1.1 Manual
This manual is designed to assist in the installation, operation, and maintenance of the
Rosemount®3144P.
Section 1: Introduction
Transmitter and Manual overview
Considerations
Return of material
Section 2: Installation
Mounting
Installation
Wiring
Power supply
Section 3: HART® commissioning
Field communicator
Configuration
Multidrop communication
Calibration
Trim the transmitter
Section 4: Foundation™ fieldbus configuration
Calibration
Hardware maintenance
Diagnostic messaging
Trim the transmitter

2
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
Section 5: Maintenance
Maintenance
Troubleshooting
Section 6: Certified safety instrumented system (safety-certified)
Information regarding Safety Certified transmitters
Appendix A: Reference data
Specifications
Dimensional drawings
Ordering information
Appendix B: Product Certifications
Product certifications
Installation drawings
1.1.2 Transmitter
Industry-leading temperature transmitter delivers unmatched field reliability and innovative
process measurement solutions:
Superior accuracy and stability
Dual and single sensor capability with universal sensor inputs (RTD, T/C, mV, ohms)
Comprehensive sensor and process diagnostics offering
IEC 61508 safety certification
Dual-compartment housing
Large LCD display
Selectable HART Revision (5 and 7) or FOUNDATION fieldbus protocols
Improve efficiency with best-in-class product specifications and capabilities:
Reduce maintenance and improve performance with industry leading accuracy and
stability
Improve measurement accuracy by 75% with Transmitter-Sensor Matching
Ensure process health with system alerts and easy to use Device Dashboards
Easily check device status and values on local LCD display with large percent range
graph
Achieve high reliability and installation ease with the industry's most rugged dual
compartment design

3
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
Optimize measurement reliability with diagnostics designed for any protocol on any host
system.
Thermocouple Degradation Diagnostic monitors the health of a thermocouple loop,
enabling preventative maintenance
Minimum and Maximum Temperature Tracking tracks and records temperature
extremes of the process sensors and the ambient environment
Sensor Drift Alert detects sensor drift and alerts the user
the Hot Backup™feature provides temperature measurement redundancy
Refer to the following literature for a full range of compatible connection heads, sensors, and
thermowells provided by Emerson®Process Management:
Temperature Sensors and Assemblies Product Data Sheet, Volume 1 (document
number 00813-0100-2654)
Temperature Sensors and Assemblies Product Data Sheet, Metric (document number
00813-0200-2654)
1.2 Considerations
1.2.1 General
Electrical temperature sensors, such as resistance temperature detectors (RTDs) and
thermocouples (T/Cs), produce low-level signals proportional to temperature. The 3144P
transmitter converts low-level signals to HART or FOUNDATION fieldbus and then transmits the
signals to the control system via two power/signal wires.
1.2.2 Electrical
Proper electrical installation is essential to prevent errors due to sensor lead resistance and
electrical noise. For HART communications, the current loop must have between 250 and 1100
ohms resistance. Refer to Figure 2-11 on page 22 for sensor and current loop connections.
FOUNDATION fieldbus devices must have proper termination and power conditioning for reliable
operation. Shielded cables must be used for FOUNDATION fieldbus and may only be grounded in
one place.
1.2.3 Environmental
Temperature effects
The transmitter will operate within specifications for ambient temperatures between –40 and
185 °F (–40 and 85 °C). Since heat from the process is transferred from the thermowell to the
transmitter housing, if the expected process temperature is near or beyond specification limits,
consider using additional thermowell lagging, an extension nipple, or a remote mounting
configuration to isolate the transmitter from the process. Figure 1-1 details the relationship
between housing temperature rise and extension length.

4
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
Figure 1-1. 3144P Transmitter Housing Temperature Rise versus Extension Length for a
Test Installation
Example:
The maximum permissible housing temperature rise (T) can be calculated by subtracting the
maximum ambient temperature (A) from the transmitter’s ambient temperature specification
limit (S). For instance, if A = 40 °C.
T = S - A
T = 85 °C – 40 °C
T = 45 °C
For a process temperature of 540 °C (1004 °F), an extension length of 3.6 inches (91.4 mm)
yields a housing temperature rise (R) of 22 °C (72 °F), providing a safety margin of 23 °C (73 °F).
A 6.0 inch (152.4 mm) extension length [R = 10 °C (50 °F)] offers a higher safety margin [35 °C
(95 °F)] and reduces temperature-effect errors but would probably require extra transmitter
support. Gauge the requirements for individual applications along this scale. If a thermowell
with lagging is used, the extension length may be reduced by the length of the lagging.
1.2.4 Moist or corrosive environments
The 3144P temperature transmitter has a highly reliable dual compartment housing designed
to resist moisture and corrosion. The sealed electronics module is mounted in a compartment
that is isolated from the terminal side with conduit entries. O-ring seals protect the interior
when the covers are properly installed. In humid environments, however, it is possible for
moisture to accumulate in conduit lines and drain into the housing.
Note
Each transmitter is marked with a tag indicating the approvals. Install the transmitter according
to all applicable installation codes, and approval and installation drawings (see Appendix B:
Product Certifications). Verify that the operating atmosphere of the transmitter is consistent
with the hazardous locations certifications. Once a device labeled with multiple approval types
is installed, it should not be reinstalled using any of the other labeled approval types. To ensure
this, the approval label should be permanently marked to distinguish the approval type(s) used.
(1,500 °F)
Temperature
Oven
(1,000 °F)
Temperature
Oven
(482 °F)
Temperature
Oven
Housing Temperature
Rise Above
Ambient °C (°F)
60 (108)
50 (90)
40 (72)
0
30 (54)
20 (36)
10 (18)
3456
789
Extension Length (in.)
815 °C
250 °C
540 °C
22
3.6

5
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
1.2.5 Installation
When choosing an installation location and position, take access to the transmitter into
account.
Terminal side of electronics housing
Mount the transmitter so the terminal side is accessible, allowing adequate clearance for cover
removal. Best practice is to mount the transmitter with the conduit entries in a vertical position
to allow for moisture drainage.
Circuit side of electronics housing
Mount the transmitter so the circuit side is accessible, providing adequate clearance for cover
removal. Additional room is required for LCD display installation. The transmitter may be
mounted directly to or remotely from the sensor. Using optional mounting brackets, the
transmitter may be mounted to a flat surface or a 2.0 inch (50.8 mm) diameter pipe (see
“Mounting” on page 192).
1.2.6 Software compatibility
Replacement transmitters may contain revised software that is not fully compatible with the
existing software. The latest device descriptors (DD) are available with new field communicators
or they can be loaded into existing communicators at any Emerson Process Management
Service Center or via the Easy Upgrade process. For more information on upgrading a field
communicator, see Section 3.
To download new device drivers, visit www.AMSSuite.com.
1.3 Return of materials
To expedite the return process in North America, call the Emerson Process Management
National Response Center (800-654-7768) for assistance with any needed information or
materials.
The center will ask for the following information:
Product model
Serial numbers
The last process material to which the product was exposed
The center will provide
A Return Material Authorization (RMA) number
Instructions and procedures to return goods that were exposed to hazardous
substances
For other locations, contact an Emerson Process Management representative.
Note
If a hazardous substance is identified, a Material Safety Data Sheet (MSDS), required by law to be
available to people exposed to specific hazardous substances, must be included with the
returned materials.

6
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
1.4 3144P revisions
HART
The initial release of the 3144P HART was device revision 3. Each additional revision had
incremental improvements. Table 1-1 summarizes these changes.
Table 1-1. HART 3144P Revisions
Software release
date
Identify device Field device driver Review instructions
NAMUR
software
revision
HART
software
revision(1)
(1) NAMUR Software Revision is located in the hardware tag of the device. HART Software Revision can be read using a HART capable
configuration tool.
HART
universal
revision(2)
(2) Device Driver file names use Device and DD Revision, e.g. 10_07. HART Protocol is designed to enable legacy driver revisions to continue
to communicate with new HART devices. To access this functionality, the new device driver must be downloaded. It is recommended to
download the new device driver to ensure new functionality.
Device
revision Manual document number
April-2012 1.1.1 27 6(3)
(3) HART Revision 5 and 7 Selectable, Thermocouple Degradation Diagnostic, Min/Max Tracking.
FOUNDATION fieldbus
The following table summarizes the 3144P fieldbus revision history.
00809-0100-4021
5 5(3)
Feb-2007 N/A 1 5 4 00809-0100-4021
Dec 2003 N/A N/A 5 3 00809-0100-4021
Table 1-2. FOUNDATION fieldbus 3144P Revisions
Device
rev.
Software
rev.
Hardware
rev. Description Date
Rev 1 1.00.011 5Initial release Mar. 2004
Rev 1 1.00.024 5Minor product maintenance, software Sep. 2004
Rev 1 1.00.024 6Minor product maintenance, hardware Dec. 2004
Rev 1 1.01.004 6Software update Oct. 2005
Rev 1 1.01.010 7Component obsolescence hardware change and
software to support the hardware change. Feb. 2007
Rev 2 2.02.003 7FF Sensor and Process Diagnostic Release (D01): Thermocouple Degradation Diagnostic and
Minimum and Maximum Temperature Tracking Nov. 2008

7
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
Rev 3 3.10.23 7Device Compliance to ITK 6.0.1. Addition of NE107
device diagnostic information. Ease of use
improvements including:
Hot Backup functionality has been
moved to the transducer block, allowing
easier configuration from the DD
Device is shipped with the simulate
switch ON, allowing device alerts
simulation without cover removal
Device has unique block names using the
last four digits (XXXX) of the output
board serial number, e.g. AI_1400_XXXX
All blocks are instantiated before
shipping, including model option code
dependent blocks. The product also has
all parameters initialized so that its
primary measurement is available with
no user changes required.
All devices ship will AI block scheduled.
Customer will be able to use old DD files
when replacing a device with a newer rev
device - This is possible for devices with
device revision number 3 and above.
Wherever possible, the product ships
with parameters initialized to common
values. The product shall ship with no
uninitialized parameters that will keep
the transmitter from providing its
primary measurement right out of the
box.
The product's default block tags are be
less than or equal to 16 characters in
length.
Custom function blocks were replaced
with enhanced function blocks.
Default block tags include underscores,
“_”, instead of white spaces.
The CF file has a better description of the
device, including meaningful defaults
and example values.
Device provides means to properly range
graphs and charts in the device
dashboards.
June 2013
Table 1-2. FOUNDATION fieldbus 3144P Revisions
Device
rev.
Software
rev.
Hardware
rev. Description Date

8
Reference Manual
00809-0100-4021, Rev GC
Section 1: Introduction
April 2014
Introduction
1.5 Confirm HART revision capability
If using HART based control or asset management systems, confirm the HART capability of
those systems prior to transmitter installation. Not all systems are capable of communicating
with HART Revision 7 protocol. This transmitter can be configured for either HART Revision 5 or
Revision 7.
Switch HART revision mode
If the HART configuration tool is not capable of communicating with HART Revision 7, the
3144P will load a Generic Menu with limited capability. The following procedures will switch the
HART revision mode from the Generic Menu.
1. Manual Setup>Device Information>Identification>Message
a. To change to HART Revision 5, Enter: “HART5” in the Message field
b. To change to HART Revision 7, Enter: “HART7” in the Message field

Reference Manual
00809-0100-4021, Rev GC
Section 2: Installation
April 2014
9Installation
Section 2 Installation
Safety messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 9
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 15
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 20
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 24
2.1 Safety messages
Instructions and procedures in this section may require special precautions to ensure the safety
of the personnel performing the operations. Information that potentially raises safety issues is
indicated by a warning symbol ( ). Please refer to the following safety messages before
performing an operation preceded by this symbol.
Explosions could result in death or serious injury.
Do not remove the transmitter cover in explosive atmospheres when the circuit is live.
Before connecting a Field Communicator in an explosive atmosphere, make sure the
instruments in the loop are installed in accordance with intrinsically safe or
non-incendive field wiring practices.
Verify that the operating atmosphere of the transmitter is consistent with the
appropriate hazardous locations certifications.
Both transmitter covers must be fully engaged to meet explosion-proof requirements.
Failure to follow these installation guidelines could result in death or serious injury.
Make sure only qualified personnel perform the installation.
Process leaks could result in death or serious injury.
Install and tighten thermowells or sensors before applying pressure, or process
leakage may result.
Do not remove the thermowell while in operation. Removing while in operation may
cause process fluid leaks.
Electrical shock could cause death or serious injury. If the sensor is installed in a
high-voltage environment and a fault or installation error occurs, high voltage may
be present on the transmitter leads and terminals.
Use extreme caution when making contact with the leads and terminals.

10
Reference Manual
00809-0100-4021, Rev GC
Section 2: Installation
April 2014
Installation
2.2 Commissioning
The 3144P must be configured for certain basic variables to operate. In many cases, these
variables are pre-configured at the factory. Configuration may be required if the variables need
to be changed.
Commissioning consists of testing the transmitter and verifying transmitter configuration data.
Rosemount®3144P transmitters can be commissioned either before or after installation.
Commissioning the transmitter on the bench before installation using a field communicator or
AMS™Device Manager ensures that all transmitter components are in working order.
For more information on using the field communicator with the 3144P transmitter, see “HART®
commissioning” on page 29. For more information on using the 3144 with FOUNDATION™
fieldbus, see Section 4: Foundation™ fieldbus configuration.
Figure 2-1. Installation Flowchart
2.2.1 Setting the loop to manual
Set the process application loop to manual when sending or requesting data that would disrupt
the loop or change the output of the transmitter. The field communicator or AMS Device
Manager will prompt to set the loop to manual, when necessary. Acknowledging the prompt
does not set the loop to manual, it is only a reminder. Setting the loop to manual is a separate
operation.
No
Yes
No
Yes
Bench
Calibration?
BASIC SETUP
Refer to
Section 5:
Maintenance
Set Units
Set Range
Values - HART
Set Sensor
Types
Set Number of
Wires
VERIFY
Simulate Sensor
Input
FIELD INSTALL
Set Jumpers or
Switches
Mount the
Transmitter
Power the
Transmitter
Check for
Process Leaks
Wire the
Transmitter
START HERE
Done
Within
Specifications?
Set Damping