Enabling Devices Peek-a-Boo 7508M User manual

8. Turn the unit on by turning the ON/OFF/Sensitivity knob switch, found on the
back of the unit, clockwise. This knob also controls the sensitivity of the bead
chains, turning the knob clockwise will decrees sensitivity, requiring ore
ove ent of the beads to activate. Turning the knob counterclockwise will
increase sensitivity, thus requiring less ove ent of the beads to activate.
9. When you anipulate the beads in any way, you will be rewarded with usic,
lights and vibration!
10. Once you stop oving the beads, there will be a brief delay, and then the
features will stop.
11. To turn On or Off the desired sti uli (1 – Light; 2 –Music; 3 Vibration), push
the s all white rocker switches to the On or Off position.
12. To use this unit as a switch to control other devices, plug one end of the supplied
double ended cord into the jack on the side of the Peek-a-Boo Mirror. Next plug
the other end into your adapted devices. Moving the beads will activate your
device, as well as the selected sti uli. Once you stop oving the beads, there
will be a brief delay and then your device will shut off.
Troubleshooting:
Problem: The Peek-a-Boo Mirror does not work.
Action #1: Check or replace the batteries with fresh new batteries.
Care of Unit:
The Peek-a-Boo Mirror can be wiped clean with any household ulti-purpose
cleaner and disinfectant.
Do not submerge the unit, as it will da age the contents and the electrical
co ponents.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
For Technical Support:
Call our Technical Service Depart ent
Monday through Friday, 9 a. . to 5 p. . (EST)
1-800-TEC-TOYS or 1-800-832-8697
custo [e-mail]
ountable Peek-a-Boo irror #7508
& 7508 ini Peek-a-Boo irror W/
ounting Arm
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. [phone] / Fax [phone]
Toll Free 800.832.8697
www.enablingdevices.co

Our ost Popular Adapted Therapeutic Toys Now Available On ounts!
For the child who needs special visual place ent, we’ve selected so e of our ost
popular adapted toys and created a syste that allows you to easily ount the on a
wheelchair, tabletop, bedrail or tray. Purchase any of the four ountable toys with or
without the ounting ar . Size: 8 "L x 9 ¾ "W. Requires 6AA Batteries. Mounting
ar is adjustable up to 24".
1. The Peek-a-Boo Mirror requires 6 AA batteries (Not included). Alkaline
batteries are required. Do not use heavy duty or rechargeable batteries because
they supply lower voltage and the unit ay not perfor as well.
2. The battery co part ents are located on the back of the unit. To re ove the
battery co part ent covers, unscrew the s all Phillips Head screws then slide
the covers off. Install new batteries, being careful to observe proper (+) & (-)
battery polarity. Replace covers and screw.
3. Cla ping Options: Our ounting cla p is designed for ounting to tubular
(wheelchair, bedrail, walker, etc.) or flat surfaces such as a table top or desk. For
flat surface ounting use the included wedge insert shoe stored in front of the
locking knob on the cla p (see Fig.1) Loosen locking knob slightly to re ove
wedge, tighten knob once wedge has been re oved.
Fig.1
4. At this point we reco end you place your ounting ar without the Peek-a-
Boo Mirror and do a rough setup, you can fine tune your adjust ents after you
have placed the Peek-a-Boo Mirror on the ar . Do not force or try adjusting the
5. ar without first loosening the set knobs for that portion of the ar . Each
section of the ar has a set knob. Once you have the ar in the desired position
you can tighten the knobs to lock the ar in place.
6. Once the ar is in position you can now place your Peek-a-Boo Mirror on the
ar . First back off the set knob on the Peek-a-Boo Mirror until it is flush with
the inside of the opening. This is necessary to allow the holder to be pushed all
the way down on the ounting ar post. The post at the end of the ar also has
a flat spot, which needs to be lined up with the set screw on the Peek-a-Boo
Mirror’s base. Once this is done you can tighten the set knob to lock the holder
to the ar . Please Note: Make sure to back the set screw enough to allow the
holder to be pushed all the way down on the post of the ar , failure to do so will
cause the Peek-a-Boo Mirror to fall off the ounting ar and a fall could cause
da age to your Peek-a-Boo Mirror. (See Fig. 2).
Fig. 2
7. You can place the Bead Chain flat on a lapboard or tabletop by first re oving
the ounting hub on the back of the unit. Si ply re ove the two Phillips head
screws holding the hub in place and lift off.
Rev 7/16/12
Tighten Set
Knob