ENDA EI1410 NTC User manual

TECHNICAL SPECIFICATIONS
ENVIRONMENTAL CONDITIONS
Height Max. 2000m
80% up to 31 decreasing linearly 50% at 40 .
Ambient/storage temperature
Max. relative humidity
0 ... +50°C/-25 ... 70°C
Rated pollution degree According to EN 60529 Front panel : IP65 , Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gases.
Thank you for choosing ENDA EI1410 NTC temperature indicator.
SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.
Yukarý Dudullu Barbaros Cad. Kutup Sok. No:20 34775 - ÜMRANÝYE/ÝSTANBUL/TÜRKÝYE
Tel : [phone] Pbx. Fax : [phone]
url : www.enda.com.tr
* 77 x 35mm sized.
* 4 digits display.
* Easy to use by front panel keypad.
* Display can be selected decimal or integer.
* Temperature unit can be selected °C or °F.
* Maximum and minimum measurement values are registered.
* Upper and lower limits of the alarm value can be adjusted
* CE marked according to European Norms.
Supply
Power consumption
2.5mm² screw-terminal connections
±
Wiring
Scale
Sensitivity
Accuracy
EMC
Safety requirements
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.
The device is designed to operate in controlled electromagnetic environment)
EN 61010-1: 2001 (Pollution degree 2, overvoltage category II)
ELECTRICAL CHARACTERISTICS
-60.0°C...150.0°C
0.1°C
Max. 4 VA
1°C
Decimal
Integer -60°C...150°C
HOUSING
Housing type Suitable for flush-panel mounting.
Dimensions W77xH35xD71mm
Weight
Enclosure material Self extinguishing plastics.
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
EI1410-230VAC Approx. 190g (after packing)
EI1410-24 and EI1410-12
EI1410-E-08
1/3
230V AC +10% -20%, 50/60Hz or 24V AC/DC 10%, 50/60Hz or 12V AC/DC 10%, 50/60Hz
± ±
Pleaseread this documentcarefullybefore using this product. The guaranteewill be invalidatedif the deviceis
damagedby not followinginstructionsdetailed in the manual. The company shall notberesponsible forany
damage or losses howevercaused, which may beexperienced asa resultof the installation oruse of this product.
Order Code : EI1410-NTC-     
1
Supply Voltage
230VAC...230V AC
24............24V AC/DC
12............12V AC/DC
Approx. 110g (after packing)
ENDA EI1410 NTC TEMPERATURE INDICATOR
SET
SET
EI 1410
ENDA
°F
°C

EI1410-E-08
2/3
DIMENSIONS
CONNECTION DIAGRAM
ENDA EI1410 is intended for installation in control panels. Make sure that the device is used only for
intended purpose. The shielding must be grounded on the instrument side. During an installation, all
of the cables that are connected to the device must be free of electrical power. The device must be
protected against inadmissible humidity, vibrations, severe soiling and make sure that the operation
temperature is not exceeded. All input and output lines that are not connected to the supply network
must be laid out as shielded and twisted cables. These cables should not be close to the power
cables or components. The installation and electrical connections must be carried out by a qualified
staff and must be according to the relevant locally applicable regulations.
7
8
SUPPLY:
NOTE :
184-253V AC
50/60Hz 4VA
Line
Neutral
230V AC
Supply
Switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Fuse should be connected.
1) Mains supply cords shall meet the requirements of
IEC 60227 or IEC 60245.
2) In accordance with the safety regulations, the power
supply switch shall bring the identification of the relevant
instrument and it should be easily accessible by the
operator.
UP.l1
UP.l1 HYS-
LO.l1
LO.l1 HYS+
Alarm
Input
t
t
When alarm case happens, process value flashes.
Equipment is protected througout
by DOUBLE INSULATION.
Holding screw 0.4-0.5Nm
Panel cut-out Note :
1) Panel thickness
should be maximum 7 mm.
2) If there is no 60mm free space at the
back side of the device, it would be difficult
to remove it from the Panel.
71mm
29mm
Flush mounting
clamp
For removing mounting clamps:
Push the flush-mounting clamp in
direction 1as shown
in the figure below. Then, pull out
the clamp in direction 2.
1
Flush mounting
clamp
Depth
Panel
2
71mm 5mm
Rubber
packing
35mm
77mm
SET
°C
SET
Ei1410
ENDA
°F
SN: XXXXXXXXX
EI1410-NTC-230VAC
NTC TEMPERATURE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
230V AC +10% -20%
50/60Hz 4VA
1 2 3 4 5 6 7 8 9 10 11 12
NTC
SENSOR
SN: XXXXXXXXX
EI1410-NTC-12
NTC TEMPERATURE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
12V AC/DC ±10%
50/60Hz 4VA
1 2 3 4 5 6 7 8 9 10 11 12
NTC
SENSOR
SN: XXXXXXXXX
EI1410-NTC-24
NTC TEMPERATURE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
24V AC/DC ±10%
50/60Hz 4VA
1 2 3 4 5 6 7 8 9 10 11 12
NTC
SENSOR
SN: XXXXXXXXX
EI1410-NTC-230VAC
NTC TEMPERATURE INDICATOR
ENDA INDUSTRIAL ELECTRONICS
230V AC +10% -20%
50/60Hz 4VA
1 2 3 4 5 6 7 8 9 10 11 12
NTC
SENSOR

EI1410-E-08
3/3
Used for displaying value of the selected parameter and adjusting
parameter.
the selected
Programming
key
Used for changing parameters and increasing the setpoint value. When held down
for a few seconds, the change rate accelerates.
Used for changing parameters and decreasing the setpoint value.
for a few seconds, the change rate accelerates.
When held down
Increment
key
Decrement
key
EI1410 PROGRAMMING DIAGRAM
If no key is pressed within 20 seconds, the device will time out back to the run mode. Alternatively, re-energizing the device, run mode is entered.
If both & keys are pressed and held for 3 seconds, programming mode is entered or run mode is returned.
Alarm
upper limit
value
While holding key, measured maximum temperature value appears.
When the device is first enerjized or by pressing key, while holding key,
measured maximum temperature value is made equal to process temperature value.
Process value
RUN MODE
PROGRAMMING MODE
Alarm lower limit value. If the process value falls below A.lol value, display flashes.
By using and keys, while holding key, the lower limit can be adjusted to desired value
between -60.0°C and A.upl.
Alarm upper limit value. If the process value exceeds A.upl value, display flashes.
By using and keys, while holding key, the upper limit can be adjusted to desired value
between A. and 150.0°C.lol
Alarm
lower limit
value
Alarm hysteresis value.
By using and keys, while holding key, hysteresis value can be adjusted to desired value
between 0.0°C and 15.0°C. Maximum value of this parameter must be ( - ) / .A.upl A.Lol 2
If this key is pressed,
upper limit value
appears.
If this key is pressed,
lower limit value
appears.
Selecting decimal place.Display can be selectable decimal or integer.
By using and keys, while holding key, display can be selected decimal or integer.
When is selected, decimal case is entered. If is selected, integer case is entered.
All of other parameters are adjusted according to selection.
Yes no
If this key is pressed,
temperature unit
appears.
Temperature unit.
By using and keys, while holding key, temperature unit can be selected °C or °F.
If this key is pressed,
display alternatives
appears.
Alarm
hysteresis
value
If this key is pressed,
hysteresis value
appears.
If this key is pressed,
offset value
appears.
Offset value.
By using and keys, while holding key, offset can be adjusted to desired value
between -20.0°C ile 20.0°C.
While holding key, measured minimum temperature value appears.
When the device is first enerjized or by pressing key, while holding key,
measured minimum temperature value is made equal to process temperature value.
Means, indicator probe is short circuit.
Means, indicator probe is broken.
ERROR MESSAGES
Means, process value is higher than the scale.
Means, process value is lower than the scale.
EI 1410
ENDA
SET
SET
°F
°C
SET
Temperature
unit
Selecting
decimal place
Offset
value
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET
SET