ENDA ETS1410 User manual

Supply voltage 230V AC +%10 -%20, 50/60Hz or 24V AC ±%10, 50/60Hz or optional 9-30V DC SMPS module.
Power consumption Max. 2VA
2.5mm² screw terminal connection
%0,01
Wiring
Display
Accuracy
EMC
Safety requirements
EN 61326-1: 1997, A1: 1998, A2: 2001 (Performance criterion B is satisfied for EMC tests.)
EN 61010-1: 2001 (pollution degree 2, over voltage category II, measurement category I)
ELECTRICAL CHARACTERISTICS
4 digits, 9.1mm, 7 segment red display LED.
OUTPUT
Auxiliary supply output 12V DC, Max. 30mA (unregulated)
ENDA ETS1410 PULSE INPUT TACHOMETER
1/2
SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.
Yukarý Dudullu 34775 - ÜMRANÝYE/ÝSTANBUL/TÜRKÝYE
Tel : [phone] Pbx. Fax : [phone]
url : www.enda.com.tr
Barbaros Cad. Kutup Sok. No:20
Panel cut-out
DIMENSIONS
ETS1410-E-02
34mm
70mm 8mm
85mm
71mm
29mm
Flush mounting
clamp Flush mounting
clamp
Depth
Rubber
packing
Panel
2
1
* 34x77 sized.
* Easy to use.
* Decimal point can be adjusted..
* Process value can be devided by a value
between 1 and 999.
* Sampling time is selected automatically
according to input frequency. Sampling time is
between 1 and 16s.
* Having Ce mark according to European Norms.
SET
ENDA
RPM
ETS 1410
TACHOMETER
SIG
SET
ENDA
RPM
ETS 1410
TACHOMETER
SIG
Input
signal
indicator
1 12 23 34 45 56 6
7 78 89 9
10 10
11 1112 12
ETS1410 DIGITAL TACHOMETER ETS1410-24AC DIGITAL TACHOMETER
+ SENSOR INPUT + SENSOR INPUT
230V AC +10% -20%
50/60Hz 2VA
24V AC ±10%
50/60Hz 2VA
+ 12V DC 30mA OUT + 12V DC 30mA OUT
GND GND
ENDA INDUSTRIAL ELECTRONICS ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX SN: XXXXXXXXX
1 2 3 4 5 6 7 8 9 10 11 12
ETS1410 DIGITAL TACHOMETER
+ SENSOR INPUT
230V AC +10% -20%
50/60Hz 2VA
+ 12V DC 30mA OUT
GND
ENDA INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
Read this document carefully before using this device. The guarantee will be expired by
damaging of the device if you don't attend to the directions in the user manual. Also we don't
accept any compensations for personal injury, material damage or capital disadvantages.
Thank you for choosing ENDA ETS1410 TACHOMETER.
CONNECTION DIAGRAM
ENDA ETS1410 is intended for installation in control panels. Make sure that the device is used
only for intended purpose.
During an installation, all of
the cables that are connected to the device must be free of energy. The device must be protected
against inadmissible humidity, vibrations, severe soiling and make sure that the operation
temperature is not exceeded. The cables should not be close to the power cables or components.
The electrical connections must be carried on by a qualified staff
and must be according to the relevant locally applicable regulations.
184-253V AC
50/60Hz 2VA
Switch
Fuse
F 100 mA
250V AC
Neutral
Line
SUPPLY :
NOTE :
Fuse should
be connected.
230V AC Supply
Cable size: 1,5mm²
1) Mains supply cords shall meet the requirements of IEC 60227or IEC 60245.
2) In accordance with the safety regulations, the power supply switch shall bring the identification of
the relevant instrument and it should be easily accessible by the operator.
Note :
Holding screw 0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
HOUSING
Housing type
Dimensions
Weight
Enclosure material
TECHNICAL SPECIFICATIONS
ENVIRONMENTAL CONDITIONS
Height Maximum 2000m
80%, up to 31 decreasing linearly 50% at 40°C °C
Ambient/storage temperature
Max. relative humidity
0 ... +50 /°C -25 ... +70°C (with no icing)
Rated pollution degree According to EN 60529 Front panel : IP60
Rear panel : IP20
Do not use the device in locations subject to corrosive and flammable gasses.
ETS1410 must not be used in location where measurement category is II, III or IV.
INPUTS
Sensor input 5 to 30V pulse
The device measures frequencies between 0.07 and 3000Hz.
Measurement frequency
Sampling time Automatically adjusted according to input frequency. Minimum: 1s, Maximum: 16s
While cleaning the device, solvents (thinner, benzine, acid etc.) or corrosive materials must not be used.
Suitable for flush-panel mounting.
W34xH77xD70mm
ETS1410 : Approx. 200g (after packing the device )
Self extinguishing plastics
Note :
1) Panel thickness
should be maximum
7 mm.
2) If there is no 60mm
free space at the back
side of the device, it
would be difficult to
remove it from the
panel.
For removing mounting clamps:
Push out the flush-mounting
clamp in direction 1as shown
in the figure below. Then, pull
out the clamp in direction 2.
1
2
Supply Voltage Order Code
230V AC +%10 -%20 ETS1410
24V AC ±%10 ETS1410-24AC
9-30V DC SMPS module ETS1410-12AC

EXAMPLES FOR USING DIVISOR PARAMETER
ENDA ETS1410 Pulse Input Tachometer divides the number pulses in one minute by the calibration
value and then, the result is displayed. Calibration value may be selected between 1 and 999. This
feature is used for precise revolution speed, line speed or sudden flow speed measurements.
Calibration value is calculated as explained below:
CAL(divisor value) =
Desired value on the display
Number of pulses per minute
Assume that a having a circumference of 25cm rotates at a speed of 3 revolutions/minutes.
And the line speed of a band moving on the cylinder is going to be calculated in the unit of cm/minute.
And, a 50 pulse/revolution encoder is used for measuring the revolution speed of the .
Dividing value is calculated as below;
cylinder
cylinder
Desired value on the display: 3 revolution/minute x 25 cm/revolution = 75 cm/minute
Number of pulses per one minute: 3 x 50 pulse/ = 150 pulse/minute
Then; CAL(divisor value) = = 2
revolution/minute evolution
Divisor value for line speed measurement;
Error messages:
Input frequency is too low or there is no signal.
Input frequency is too high.
Measured value is greater than 9999.
150 pulse/minute
75 cm/minute
SET
Parameter
Parameter
D.P. 0
C. 1
D.P. 1
C. 2
D.P. 2
C. 3
D.P. 1
C. 2
Decimal point parameter can be adjusted by using and keys.
If this parameter is selected 0, no decimal point is observed.
If the keys are pressed and hold for 0,6s, increase and decrease rates accelerate.
between 0 and 3
Divisor parameter can be adjusted between 1 and 999 by using and keys.
If the keys are pressed and hold for 0,6s, increase and decrease rates accelerate.
If key is pressed for 5 seconds, parameter adjustment mode is entered.
SET
PARAMETER ADJUSTMENT MODE
2/2
SÝSEL MÜHENDÝSLÝK ELEKTRONÝK SAN. VE TÝC. A.Þ.
Yukarý Dudullu 34775 - ÜMRANÝYE/ÝSTANBUL/TÜRKÝYE
Tel : [phone] Pbx. Fax : [phone]
url : www.enda.com.tr
Barbaros Cad. Kutup Sok. No:20
ETS1410-E-02