Englefield VALENCIA Slim Vanity User manual

1457295-A02-B 9/12/2020
INSTALLATION
INSTRUCTIONS
FURNITURE
VALENCIATM Slim Vanity
Contemporary design and
quality construction,
providing affordable storage
for bathrooms of any size or
style.
It’s the details that Englefield
cares about - from pioneering
the latest technology, to
innovative design.
1

BEFORE YOU BEGIN
ROUGH-IN
INSTALLATION INSTRUCTIONSVALENCIA
TM
Slim Vanity
Please read these instructions carefully to familiarise yourself with the required tools, materials, and
installation sequences. Follow the sections that pertain to your particular installation. This will help you
avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.
Prior to installation, inspect cabinet and top to ensure that no damage has occurred in transit. If damage
has occurred, or a visible defect exists, do not proceed with installation, and advise your supplier
immediately.
Please leave these instructions for the consumer. They contain important information.
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing.
changes without further notice.
ENGLEFIELD
2
Drain cut out
centered
600 750 900
420 395
90 90 90
50 50 50

1 Drawer removal
Cabinets must be fixed to a nog and at least one stud in the wall. The nog size should be 50 x 75mm.
Use a stud finder to locate studs & nogs in finished walls.
(a) Open the drawer and
carefully lift up on the end of
the drawer to release it from
the runner locator pins. It may
be necessary to gently pry the
runner away from the drawer.
(b) The drawer is now only held
by the runner hooks at the
back and can be pulled out in
the direction shown.
CONSTRUCTION REQUIREMENTS
INSTALLATION
TOOLS AND MATERIALS REQUIRED - (Not Supplied)
INSTALLATION INSTRUCTIONSVALENCIA
TM
Slim Vanity
To suit pipework To suit screws
TOOLS MATERIALS - Not supplied & must be purchased separately
Fixing washers
20mm
Head Screws
10g x 75mm Pan
3
Stud finder
Locator pin Runner hook
50
850
A height of 850mm from the
floor to the top of the vanity
top is recommended.
50mm from top of
cabinet to centre
of nog.
overflow
DN32 waste with

INSTALLATION INSTRUCTIONSVALENCIA
TM
Slim Vanity
3 Fixing the vanity to the wall
(c) Having drilled the required holes fit the cabinet
into position over the pipework.
(e) Fix the cabinet to the wall using at least 6
screws (min 10g x 75mm) and *20mm washers.
Screw through the back wall so that they screw
into the nog and stud(s) in the wall behind.
*Washers must be used to spread the load.
NOTE: Before fastening the cabinet make sure
that it is sitting level and square.
NOTE: Screws should be positioned evenly
and fixed into nogs or studs.
(b) With a suitably sized hole saw drill the holes
for the water supply and waste.
ENGLEFIELD
4
50mm
Maximum
height
240mm
NOTE 2: Ensure that plumbing holes are positioned
to allow for a maximum height of 240mm between
the bottom of the basin to the base of the trap.
2 Water supply and waste pipe holes
(a) Measure and mark the centres for water
supply and waste pipes on the back of the
cabinet.
4 Vanity top
(a) Unpack the top and check for any damage
that might have occured in transit. Check and
confirm the fit of your selected tapware.
(b) Apply a continuous bead of silicone (not
supplied) to the top edge of the cabinet sides
and back. Ensure there are no gaps in the
sealant bead. This will ensure the top stays
securely fitted to the cabinet and no water
spillage will find its way into the cabinet.
No silicone on
front edge
(c) Place the vanity top onto the cabinet ensuring
that the back is flush against the wall and
there is an even overhang on either side of the
cabinet.
(d) Wipe off any excess sealant.
NOTE 1: Either a Dux or Aqualine Telescopic Tight
P trap is recommended for the Valencia SLIM range
of vanities.

(a) To re-install the drawer, extend the runners.
Place the drawer onto the runners and slide it
back so that the runner hooks insert into the
rear of the drawer.
(b) Make sure the locator pins line up with the
holes in the bottom of the drawer and press
the drawer down so that the pins slot into
place.
6 Drawer re-installation
(a) All edges MUST be sealed with an approved
Silicone Sealant.
8 Sealing
INSTALLATION COMPLETE
INSTALLATION INSTRUCTIONSVALENCIA
TM
Slim Vanity
(a) Select a basin mixer which is suitable for the
tap hole position of this Slim vanity range.
(c) Connect the water supply to the taps and waste
pipe to the waste outlet.
(d) Run hot and cold water and check for leaks.
When satisfied with the results move on to the
next section.
ENGLEFIELD
5
Locator pin
Runner hook
5 Waste and tapware
CLEANING AND MAINTENANCE
INSTRUCTIONS
For cleaning instructions, please refer to the
Owner’s Information Leaflet.
CONTACT AND WARRANTY
INFORMATION
Please visit our website for warranty and other
information.
Please refer to the Owner’s Information Leaflet
for contact information.
NEW ZEALAND
KOHLER NZ LTD
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
www.englefield.com
50mm
(b) Fit the waste and tapware.
7 Drawer adjustment
(a) To tilt the drawer backwards, lift the drawer
body from the locator pin and turn the dial
anti-clockwise. To tilt the drawer forwards turn
the dial clock-wise.