Englefield VALENCIA SLIM VANITY User manual

1232449-A02-D September 2023 englefield.co.nz Page1
VALENCIA SLIM VANITY
FURNITURE | ®

BEFORE YOU BEGIN:
ROUGH-IN:
Please read these instructions carefully to familiarise yourself with the required tools, materials, and
installation sequences. Follow the sections that pertain to your particular installation. This will help you
avoid costly mistakes. In addition to proper installation, read all operating and safety instructions.
Prior to installation, inspect cabinet and top to ensure that no damage has occurred in transit. If damage
has occurred, or a visible defect exists, do not proceed with installation, and advise your supplier
immediately.
Instructions, drawings, and diagrams contained in this manual present information available at the time
of printing.
Although every attempt has been made to keep them up-to-date, Englefield reserves the right to implement
product changes without further notice.
englefield.co.nz
Page2
1232449-A02-D September 2023
Please leave these instructions for the consumer. They contain important information.
Cabinets must be fixed to a nog and at least one stud in the wall.
The nog size should be 50 x 75mm.
Use a stud finder to locate studs & nogs in finished walls.
INSTALLATION INSTRUCTIONS
VALENCIA Slim Vanity
CONSTRUCTION REQUIREMENTS
Drain cut out
centered
600 750 900
423
365
90 90 90
50 50 50
50
850
®
A height of 850mm from the floor
to the top of the vanity top is
recommended.
50mm from top of cabinet to
centre of nog
.

englefield.co.nz
Page3
(C) With a suitably sized hole saw drill the holes.
(a) Measure and mark the centres for water
supply and waste pipes on the back of the
cabinet.
NOTE 1: Either a Dux or Aqualine Telescopic
Tight P trap is recommended for the Valencia
SLIM range of vanities.
NOTE 2: Ensure that plumbing holes are
positioned to allow for a maximum height of
240mm between the bottom of the basin to
the base of the trap.
(a) Open the drawer and carefully lift up on
the end of the drawer to release it from
the runner locator pins. It may be necessary
to gently pry the runner away from the
drawer.
(b) The drawer is now only held by the
runner hooks at the back and can be pulled
out in the direction shown.
1232449-A02-D September 2023
INSTALLATION INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED - (Not Supplied)
1 Drawer removal 2 Water supply and waste pipe holes
To suit pipework To suit screws
TOOLS MATERIALS - Not supplied & must be purchased separately
Fixing washers
20mm
Head Screws
10g x 75mm Pan
Stud finder
overflow
DN32 waste with
INSTALLATION
Locator pin
Runner hook
Maximum
height
240mm
VALENCIA Slim Vanity
®

3 Fixing the vanity to the wall
4 Vanity top
englefield.co.nz
Page4
(b) With a suitably sized hole saw drill the
holes for the water supply and waste.
(c) Having drilled the required holes fit the
cabinet into position over the pipework.
NOTE: Before fastening the cabinet make
sure that it is sitting level and square.
NOTE: Screws should be positioned evenly
and fixed into nogs or studs.
(e) Fix the cabinet to the wall using at least
6 screws (min 10g x 75mm) and *20mm
washers.
Screw through the back wall so that they
screw into the nog and stud(s) in the wall
behind.
*Washers must be used to spread the load.
(a) Unpack the top and check for any
damage that might have occurred in transit.
Check and confirm the fit of your selected
tapware.
(b) Apply a continuous bead of silicone
(not supplied) to the top edge of the
cabinet sides and back. Ensure there are
no gaps in the sealant bead. This will
ensure the top stays securely fitted to the
cabinet and no water spillage will find its
way into the cabinet.
(c) Place the vanity top onto the cabinet
ensuring that the back is flush against the
wall and there is an even overhang on either
side of the cabinet.
(d) Wipe off any excess silicone sealant.
1232449-A02-D September 2023
INSTALLATION INSTRUCTIONS
No silicone
on front edge.
=
=
VALENCIA Slim Vanity
®
Mounting brackets screw positioning
50
50
Mounting
bracket
50mm
200mm
50mm
50mm
100mm
100mm
100mm
50mm

Page6
1232449-A02-D September 2023
INSTALLATION INSTRUCTIONS
For cleaning instructions, please refer to the Owner’s Information Leaflet.
englefield.co.nz
Compression moulded vanity top:
To clean use non abrasive soap and water. It is recommended that the product surface is
wiped dry after each use to prevent the build up of soap and scum.
Vanity cabinet:
The materials used in the vanity cabinet are water resistant only, not water proof.
Care must be taken to clean up all water spillage onto the vanity cabinet surfaces.
To maintain the finish on your vanity cabinet clean with mild soapy water and dry with a soft
cloth.
CLEANING AND MAINTENANCE INSTRUCTIONS
CAUTION
Material used in cabinet is water resistant only, not waterproof.
Care must be taken to clean up all water spillage.
WARNING
FOR YOUR PERSONAL SAFETY AND PRODUCT DURABILITY,
ENSURE THAT HOT WATER SUPPLY IS REGULATED TO 55 C MAXIMUM
VALENCIA Slim Vanity
®
CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
Kohler New Zealand Limited
0800 100 382
AUSTRALIA
englefield.com
info@englefield.co.nz
englefield.co.nz

5 Waste and tapware
(a) All edges MUST be sealed with an
approved Silicone Sealant.
(a) Select a basin mixer which is suitable for
the tap hole position of this Slim vanity
range.
(b) Fit the waste and tapware.
(c) Connect the water supply to the taps and
waste pipe to the waste outlet.
(d) Run hot and cold water and check for leaks.
When satisfied with the results move on to
the next section.
Page5
1232449-A02-D September 2023
INSTALLATION INSTRUCTIONS
englefield.co.nz
50mm
6 Drawer re-installation
8 Sealing
7 Drawer adjustment
(b) Turn anticlockwise on the locator pin
spacer to raise the height of the drawer and
turn clockwise to raise down. Repeat on the
other runner.
INSTALLATION COMPLETE
VALENCIA Slim Vanity
®
a) To re-install the drawer, extend the runners.
Place the drawer onto the runners and slide it
back so that the runner hooks insert into the
rear of the drawer. Runner hook
*Mount Screws will
need to unscrewed
before removing the
drawer for latest
runners setup.
( b) Make sure the locator pins line up with the
holes in the bottom of the drawer and press
the drawer down so that the pins slot into
place.
Locator pin
Note: All drawers are aligned during assembly. However
further adjustment is often required after installation.
Please ensure the cabinet has not been twisted
and installed correctly before adjusting.
Height Adjustment Front Sectional View
UP
DOWN