Englefield VALENCIA ELITE User manual

1371376-A02-C March 2019
INSTALLATION
INSTRUCTIONS
SHOWER
Engleeld
VALENCIA ELITE Round Sliding
Englefield has a history
of making superb showers
and their popularity is
testament to their quality
and affordability.
It’s the details that Englefield
cares about - from pioneer-
ing the latest technology, to
innovative design, it’s all to
make your showering
experience the very best it
can be.
Note: Tapware and accessories not included.

Page 1
Before installing the shower please read these instructions carefully to familiarise
yourself with the required tools, materials and installation sequences. Please leave these
instructions for the consumer after installation. Refer to the separate care and maintenance
guide for important care and cleaning information.
Ensure that the shower tray and wall, if applicable, are completely finished prior to
installing your shower door and return. Follow all warnings, cautions and instructions
contained in this guide.
1. ENGLEFIELD strongly recommends that a minimum of TWO persons install this
enclosure due to the weight of the door panels.
2. Toughened safety glass cannot be cut. Risk of injury or product damage.
3. Wear protective footwear when lifting panels.
4. Wear safety glasses when drilling.
1. The wall retainers must be installed onto a waterproof, vertical and flat wall surface.
Failure to do so will result in an unsatisfactory seal, which may cause property damage.
The wall inclination (out of squareness) is recommended to be out by no more than
+/- 4mm/m.
2. Please install this door onto an ENGLEFIELD Quick - Fit Low Profile
shower tray only, unless installing directly onto tiled walls and floor.
®
3. Care must be taken when drilling into walls and floors to avoid any hidden pipes or
wires.
4. It is the responsibility of the INSTALLER to ensure that the installation complies with
council and or local authority bylaws.
INSTALLATION INSTRUCTIONSVALENCIA ELITE Round Sliding
BEFORE YOU BEGIN
SAFETY
!
!ATTENTION
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing.
changes without further notice.
ENGLEFIELD

Page 2
INSTALLATION INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED
PARTS IDENTIFICATION
ENGLEFIELD
3.0 mm
2.0 mm - supplied
#1
Square
Drive
& Phillips
2 x Wall
Channels
2 x Rails
2 x Seal Packs
(6 seals in total) 2 x Corner
Covers
2 x Doors
2 x Fixed Panels
1 x Fittings Kit
(contents on pg 3)
2 x Handle Kits
(contents on pg 3)
VALENCIA ELITE Round Sliding
2 x Wall
Finishing Strips

Page 3
INSTALLATION INSTRUCTIONS
ENGLEFIELD
1 x Fittings Kit
2 x Handle Kits

Handle Assembly

8x Roller Caps

2x Cover Caps

2x Cover Caps

8x Short Screws

16x Fixing Screws

Hex Key


VALENCIA ELITE Round Sliding

CONSTRUCTION REQUIREMENTS
Due to the weight of the glass panels Englefield strongly recommends
constructing double studs (as below) to fix the wall retainers to.
!ATTENTION
Page 4
INSTALLATION INSTRUCTIONS
A
Double
studs
Double
studs
B
ENGLEFIELD
VALENCIA ELITE Round Sliding
Size Dim ‘A’
900 x 900 900
1000 x 1000 1000
Dim ‘B’
900
1000
1200 x 900 LH
1200 x 900 RH
1200 900
900 1200

Tray: For tray installation refer to the instructions supplied with the tray.
Wall: For wall installation refer to the instructions supplied with the wall.
- Proceed to Door and Return Installation.
- The door and return can be installed directly onto the wall and floor tiles.
- Proceed to Door and Return Installation.
OPTION 1 - Acrylic Wall & Tray
OPTION 2 - Tiled Wall & Acrylic Tray
Page 5
INSTALLATION INSTRUCTIONS
OPTION 3 - Tiled Wall & Floor
ENGLEFIELD
INSTALLATION - Options
Tray: For tray installation please refer to the instructions supplied with the tray.
Wall:
- The vertical wall retainers MUST be installed onto the waterproof membrane PRIOR TO
WALL TILING. If possible the complete door system should be installed onto the
waterproof membrane prior to wall tiling.
CAUTION: Failure to install the wall retainers first may
mean the door system may not fit on the shower tray
due to the tile thickness.
- If not installing the complete door system prior to tiling,
install the wall retainers and tiles. The retainer cover
extrusion can be inserted after tiling - there is no need
to leave a tiling gap. Refer to image.
- Proceed to Door and return installation.
Tile up to
retainer
VALENCIA ELITE Round Sliding

Caution: Ensure tray or tiled floor is
level & walls are vertical & square.
For tray base option:
- Mark 10mm in from top edge of tray.
For tiled base option:
- Mark from finished wall to outer edge
of retainer.
Tip: Cover the waste to prevent the loss of
small parts. If installing onto a tray protect
the tray surface during installation.
Page 5
10 mm
10 mm
Page 6
INSTALLATION INSTRUCTIONS
ENGLEFIELD
INSTALLATION
1
B
A
(a) Mark the locations of the wall retainers.
± 0 mm ± 0 mm
VALENCIA ELITE Round Sliding
900 x 900
1000 x 1000
1200 x 900 LH
1200 x 900 RH
875 875
975 975
1175 875
875 1175
ASize B

Page 7
INSTALLATION INSTRUCTIONS
ENGLEFIELD
2
± 0 mm
3 mm x4
10 mm
x4
(a)
Position the wall channels on the wall. The flange with pre-drilled holes should face
inside the shower enclosure. Using a level, make sure that the channel is upright.
Mark the position of the fixing holes down the centre of the channel, then remove
the channel.
Drill with a 3mm bit. For other types of wall structure, alternative fixings may be
required (not supplied).
(b)
(c)
Apply silicone sealant along the length of the wall and at the bottom where the wall
channel will be placed, including the top of the tray.
(d)
Position the wall channels on the wall and install the fixing screws.
(e)
Fully tighten the fixing screws, making sure that the wall channels are upright.
(f)
Repeat the process for the other wall channel.
(g)
VALENCIA ELITE Round Sliding

Page 8
INSTALLATION INSTRUCTIONS
ENGLEFIELD
(a)
(b)
(c)
(d)
(e)
Place one of the curved rails onto the floor and insert the glass panels, making sure
the glass locates correctly in the seal.
Logo badge on
outside of shower
(CleanLess ® glass
protection to inside)
Note! This process requires two persons. Assemble outside the shower area.
Install the fixing screws to secure the glass panel frames to the bottom rail.
Place the other curved rail in position, making sure that it locates correctly over the
glass panels.
Install the fixing screws to secure the glass panel frames to the top rail.
Retighten all the screws, making sure that the whole assembly is secure and square.
3
VALENCIA ELITE Round Sliding

Page 9
INSTALLATION INSTRUCTIONS
ENGLEFIELD
(a)
(b)
Lift the shower assembly into position and fit the upright frame posts into the fixed
wall channels on both sides of the enclosure.
Centralise the enclosure within the wall channels and make sure everything is level.
4
Note! This process requires two persons.
Make sure the enclosure is kept parallel when lifting into place.
VALENCIA ELITE Round Sliding
!

Page 10
INSTALLATION INSTRUCTIONS
ENGLEFIELD
5
Ø 3 mm
x4
x4
± 0 mm
(b) Insert the short screws and tighten.
(c) Repeat the process for the other wall channel.
(a) From the inside of the shower enclosure, drill four 3mm holes in the door frame.
The hole locations are centre marked on the inside of the wall channel.
Caution! Take care not to drill all the way through or damage the shower.
VALENCIA ELITE Round Sliding
!

Page 11
INSTALLATION INSTRUCTIONS
ENGLEFIELD
6
Rotate 90°
Unlocked Locked
(a) Hang the door onto the top rail.
Note! Make sure that the roller adjusting screws are facing downwards.
(b) Adjust the top rollers with the adjusting screw until the bottom rollers easily clip
into the bottom rail.
(c) Adjust the rollers to give a smooth, even action when the door is opened and closed.
(d) Fit the seals. Note! The longer seal goes on the door. Trim any excess material.
(e) Lock the top roller assemblies in position by turning the lock through 90º.
(f) Fit the roller covers.
VALENCIA ELITE Round Sliding

wall board
retainer
channel
silicone
silicone or
adhesive
finishing
strip wall
liner
Page 12
INSTALLATION INSTRUCTIONS
ENGLEFIELD
7
VALENCIA ELITE Round Sliding
(a)
Install the door handle, ensuring that the grub screws are on the underside.
Fit the corner covers to the wall channels. They should ‘snap’ into place.
(b)
Apply sealant along the outside surfaces of the enclosure. Do not seal from inside.
Fit the caps to the top of the extrusions. Add silicone or modify caps to fit if required.
(c)
Install the wall finishing strips, if desired.
(d)
Allow the silicone sealant to cure for 24 hours before use.
(e)
(f)
Installation complete.
24hrs
200mm up
full length
full length
full length
200mm up

CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
Engleeld
INSTALLATION INSTRUCTIONS
For warranty information, please visit our website.
VALENCIA ELITE Round Sliding
Return Panel
1365850-** (9x9 & 12x9 short return)
1365851-** (1x1)
1365852-** (12x9 long return)
Wall Channel
1278347-**
Top/Bottom Rail
(pre-installed bumpers etc)
1278353-** (9x9)
1278354-** (1x1)
1386137-** (12x9 RH top, LH bottom)
1386136-** (12x9 LH top, RH bottom)
** Colour code must be specified when ordering
Door (glass only)
1365846
Top Roller
1260199
Bottom Roller
1260200
Return Seal
1321480
Vertical Seal (door)
1382128 Vertical Seal (return) 1382129 Magnetic Seal Pack 1260197
Retainer Cover
1278348-**
Glass Aftercare Kit
98945A-NA Fittings Kit
1376823-**
Handle Assembly
1365840-**
Wall Finishing Strip
1315530-**
CLEANING AND MAINTENANCE INSTRUCTIONS
Please refer to the homeowners guide and our website for cleaning instructions.
SPARE PARTS
Scan the QR barcode on the packaging or underside of top caps to identify the product SKU and date of manufacture.
!