Englefield MILANO Square User manual

1213895-A02-G 25/07/2017
INSTALLATION
INSTRUCTIONS
SHOWER
Englefield
MILANO
TM
Square
Note: Tapware not included.
Englefield has a history
of making superb showers
and their popularity is
testament to their quality
and affordability.
It’s the details that Englefield
cares about - from pioneer-
ing the latest technology, to
innovative design, it’s all to
make your showering
experience the very best it
can be.

Page 1
Before installing the shower please read these instructions carefully to familiarise
yourself with the required tools, materials and installation sequences. Please leave these
instructions for the consumer after installation. Refer to the separate care and maintenance
guide for important care and cleaning information.
Ensure that the shower tray and wall, if applicable, are completely finished prior to
installing your shower door and return. Follow all warnings, cautions and instructions
contained in this guide.
1. ENGLEFIELD strongly recommends that a minimum of TWO persons install this
enclosure due to the weight of the door panels.
2. Toughened safety glass cannot be cut. Risk of injury or product damage.
3. Wear protective footwear when lifting panels.
4. Wear safety glasses when drilling.
1. The wall retainers must be installed onto a waterproof, vertical and flat wall surface.
Failure to do so will result in an unsatisfactory seal, which may cause property damage.
The wall inclination (out of squareness) is recommended to be out by no more than
+/- 4mm/m.
2. Please install this door onto an ENGLEFIELD Quick - Fit Low Profile
shower tray only, unless installing directly onto tiled walls and floor.
®
3. Care must be taken when drilling into walls and floors to avoid any hidden pipes or
wires.
4. It is the responsibility of the INSTALLER to ensure that the installation complies with
council and or local authority bylaws.
INSTALLATION INSTRUCTIONSMILANO Square
BEFORE YOU BEGIN
SAFETY
!
!ATTENTION
Instructions, drawings, and diagrams contained in this manual present information available at the time of printing. Although every
attempt has been made to keep them up-to-date, Engleeld reserves the right to implement product changes without further notice.

CONSTRUCTION REQUIREMENTS
TOOLS AND MATERIALS REQUIRED
Due to the weight of the glass panels Englefield strongly recommends
constructing double studs (as below) to fix the wall retainers to.
!ATTENTION
Page 2
INSTALLATION INSTRUCTIONSMILANO Square
3.0 mm 2.5 mm
Supplied Supplied
N0. 1 Square 3.0 mm Phillips
A
Double
studs
Double
studs
B
Size Dim ‘A’
900 x 900 900
1000 x 1000 1000
Dim ‘B’
900
1000
1200 x 900 LH 1200
1200 x 900 RH 900
900
1200

Door Pack
Return Pack
PARTS IDENTIFICATION
Page 3
INSTALLATION INSTRUCTIONSMILANO Square
Extrusion - Door wall retainer
Door Panel
Return Panel
Door Handle Assembly
Extrusion - Door drip seal
Hardware Pack
Door Handle Pack
PAN screw - ST 3.5 x 35mm
PAN screw - ST 3.9 x 12mm
x 1
x 1
x 1
x 1
x 1
Extrusion - Door edge seal
(1200 x 900 only)
x 1
x 1
x 1
x 4
x 1
x 2
x 1
x 1
x 1
x 1
x 1
x 1
Extrusion - Return wall retainer
Extrusion - Wall retainer cover
Extrusion - Wall retainer cover
Hardware Pack
PAN screw - ST 3.5 x 35mmx 4
x 4
PAN screw - ST 3.5 x 9mm
Cover - Return wall retainer (LH)
Cover - Return wall retainer (RH)
Cover - Return extrusion
Cover - Door wall retainer (LH)
Cover - Door wall retainer (RH)
Cover - Door extrusion
Allen key
- 2.5mm
x 1 Allen key - 3mm
x 4
PAN screw - ST 3.5 x 9mm
x 4
Glass Aftercare pack
x 1

Tray: For tray installation refer to the instructions supplied with the tray.
Wall: For wall installation refer to the instructions supplied with the wall.
- Proceed to Section 2 - Door and return installation.
- The door and return can be installed directly onto the wall and floor tiles.
- Proceed to Section 2 - Door and return installation.
OPTION 1
Acrylic Wall & Tray
OPTION 2
Tiled Wall & Acrylic Tray
OPTION 3
Tiled Wall & Floor
1 - INSTALLATION - Options
OPTION 1 - Acrylic Wall & Tray
OPTION 2 - Tiled Wall & Acrylic Tray
Page 4
INSTALLATION INSTRUCTIONSMILANO Square
OPTION 3 - Tiled Wall & Floor
Tray: For tray installation please refer to the instructions supplied with the tray.
Wall:
- The vertical wall retainers MUST be installed onto the waterproof membrane PRIOR TO
WALL TILING. If possible the complete door system should be installed onto the
waterproof membrane prior to wall tiling.
CAUTION: Failure to install the wall retainers first may
mean the door system may not fit on the shower tray
due to the tile thickness.
- If not installing the complete door system prior to tiling,
install the wall retainers and tiles. The retainer cover
extrusion can be inserted after tiling - there is no need
to leave a tiling gap. Refer to image.
- Proceed to Section 2 - Door and return installation.
Tile up to
retainer

(e) Fix wall retainer to wall using 4
screws (supplied).
± 0 mm ± 0 mm
3 mm
Door wall retainer Return wall retainer
x4
2.1 Wall Retainers
Caution: Ensure tray or tiled floor is
level & walls are vertical & square.
(a) Mark the locations of the wall retainers.
For tray base option:
- Mark 10mm in from top edge of tray.
For tiled base option:
- Mark from finished wall to outer edge
of retainer.
(c) Position a wall retainer on a wall with
flat side facing outwards. Use a level to
make sure it is upright. (This is critical
to ensure correct operation of the door).
(b) This shower is reversible. Please
choose which side you would like the
door to be on and install wall retainers
accordingly.
(d) Mark position of fixing holes, then
remove wall retainer and drill holes
using an appropriate 3mm drill bit
(not supplied).
Tip: Cover the waste to prevent the loss of
small parts. If installing onto a tray protect
the tray surface during installation.
2 - INSTALLATION
Page 5
INSTALLATION INSTRUCTIONSMILANO Square
10 mm
10 mm
x4
± 0 mm
x 4
PAN ST 35mm
B
900 x 900
1000 x 1000
1200 x 900 LH
1200 x 900 RH
875 875
975 975
1175 875
875 1175
ASize B
A

(a) Slot return panel into wall retainer and
hold in position (Check orientation.
Make sure horizontal aluminium
extrusion is at the bottom and glazing
gasket is on the inside).
(a) Slot door frame into wall retainer.
(Check orientation. Make sure handle
holes are on return side).
(b) Swing door frame towards return and
carefully click door corner post into return
corner post (Make sure there is no gap
where posts join and that post tops are
flush with each other).
Refer to post profiles below:
Post profiles:
ReturnDoor
(a) Remove corner post seal.
Page 6
INSTALLATION INSTRUCTIONSMILANO Square
2.2 Return
2.4 Frame Fixing - Corner Posts
2.3 Door

(b) Firmly hold corner posts together and
drill 4 x 3mm holes in return corner post
through pre-drilled holes in door corner
post.
(a) Place a clear plastic washer onto
threaded side of each spline.
Note orientation.
(b) Insert splines into holes in glass door
from inside of shower and place a
second clear plastic washer onto each
spline. Note orientation.
(c) Screw splines tightly into handle.
(d) Slide complementing handle onto
splines. Grub screw holes must face
down. Note orientation.
(c) While holding corner posts together
fix posts with 4 x PAN ST 12mm screws
(supplied).
(d) Re-install seal into extrusion ensuring
seal is fully engaged along full length.
Lubricating seal with soapy water will
help with installation.
Page 7
INSTALLATION INSTRUCTIONSMILANO Square
2.5 Door Handle
x4
3 mm

(a) Ensure distance from edge of tray to
frame extrusions is equal.
(e) Insert and tighten handle grub screws
using hex key (supplied).
(b) Ensure corner post faces are plumb
and vertical. Adjust panel engagement
in wall retainers as necessary. This step
is critical to ensure correct operation of
the door.
(c) Drill 4 x 3mm holes from inside shower
enclosure in door extrusion through
pre-drilled holes in wall retainer.
(d) Fix extrusion to wall retainer with
pan screws (supplied).
(e) Repeat steps (c) and (d) for other
wall retainer.
Page 8
INSTALLATION INSTRUCTIONSMILANO Square
2.5 Frame Fixing - Wall Retainers
3 mm
x4
± 0 mm ± 0 mm
= =
=
=
x 4
PAN ST 9mm
2.5mm
2.5mm

(b) Place 2 caps on top of wall retainers.
Left and right hand caps supplied to be
used depending on your door orientation
Apply a small bead of silicone to secure
if necessary.
(c) Place cap on top of corner posts.
Page 9
INSTALLATION INSTRUCTIONSMILANO Square
2.6 Covers & Caps
(a) Cut drip seal to length and press fit onto
bottom of door on both sides of hinge.
Ensure seals are flush with sides of
hinge and edges of glass. Notch end of
seal to allow space for vertical door seal.
2.7 Seal installation
2.7.1 Drip seals
RETURN SIDEDOOR SIDE
Notch in
end of seal
Profile
Profile
(a) Install retainer cover panel on wall
retainer. Place cover against retainer,
then firmly push inwards over clip to
If necessary place a piece of wood
secure in position.
against the cover and tap gently with a
soft hammer.
Repeat for other retainer cover panel.
Door wall retainer
Return wall retainer

Page 10
INSTALLATION INSTRUCTIONSMILANO Square
(a) Door glass position can be adjusted at
the hinges.
(b) To adjust hinge slide off hinge cover
and turn screw located in the hinge
with allen key.
2.8 Hinge adjustment
(a) Adjust catch force by turning screw
through roller with allen key.
2.9 Door roller Catch adjustment
2.7.2 Door edge seal (1200 x 900 only)
2.5mm
3.0mm
(a) Cut door edge seal to length and notch
bottom end of seal to allow space for
horizontal door seal. Press fit onto edge
of door (Seal flap must be on inside
of shower).
Profile
Notch in
Flap must be on
inside of shower
end of seal

(a) Apply sealant in accordance with the sealant manufacturers instructions along
the outside surfaces of the door frame only. Allow the sealant to cure for 24 hours
before use.
Entire length Entire length
Entire length Entire length
200mm up
200mm up
2.10 Shower Sealing
Page 11
INSTALLATION INSTRUCTIONSMILANO Square
200mm up

SPARE PARTS
Page 12
INSTALLATION INSTRUCTIONSMILANO Square
Door
Cap
Wall retainer
1291624-L
1291624-R
Screw
PAN ST 3.5 x 9mm
1218007
Cap
Door frame
1203357
Extrusion
Wall retainer
1270108-N-SHP
Extrusion
Door frame
1203375-SHP
Extrusion
Top sill
1203379-T-SHP (1000)
1203381-T-SHP (900)
1203377-B-SHP (1200 x 900)
Roller Catch
Top or bottom
1203397
Seal
Door hinge side
1203414
(900 & 1000 only)
Seal
Door edge
1210498
(1200 only)
Extrusion
Bottom sill
1203379-B-SHP (1000)
1203381-B-SHP (900)
1203377-T-SHP (1200 x 900)
Seal (notched)
Door catch side
1203418
Extrusion
Door corner post
1203376-SHP
Screw
PAN ST3.5 x 35mm
1108382
Cap
Door frame
1203357
Screw
PAN ST 3.9 x 12mm
1203404
Extrusion
Wall retainer cover
1270107-N-SHP
Glass
Fixed panel
1275436
(1200 only)
Allen Key
3mm
1095457
Allen Key
2.5mm
1157853
Seal
Glazing gasket
1157883
(1200 only)
Seal
Glazing gasket
1157883
(1200 only)
Seal
Door drip
1210597

Page 13
INSTALLATION INSTRUCTIONSMILANO Square
Return
Extrusion
Bottom sill
1203369-SHP (1000)
1203368-SHP (900)
Extrusion
LH Return frame post
1203371-L-SHP
Cap
Wall retainer
1291625-R
(1291625-L)
Cap
Return glass retainer
1203359
Cap
Corner post
1203357
Screw
PAN ST3.9 x 12
1203404
Screw
PAN ST3.9 x 12
1203404
Insert
Return glass
1203413
Insert
Return glass
1203413
Insert
Return glass
1203413
Insert
Return glass
1203413
Seal
Glazing gasket
1157901
Seal
Glazing gasket
1157901
Extrusion
RH Return frame post
1203371-R-SHP
Extrusion
Return wall retainer
1270104-N-SHP
Extrusion
Wall retainer cover
Screw
PAN ST3.5 x 35mm
1108382
Screw
PAN ST 3.5 x 9mm
1218007
Screw
PAN ST3.9 x 12
1203404
Screw
PAN ST3.9 x 12
1203404
1270107-N-SHP

INSTALLATION INSTRUCTIONSMILANO Square
Handle
Hinges
- Assembly with Dual handles
1210600-SHP
Hinge Assembly
1203392-SHP
Allen Key
2.5mm
1157853
Pin
Hinge
1203394
Screw
Hinge base
1102118
Base
Hinge pin
1203393
Bush
Hinge pin
1203388
Cover
Hinge inner
1203387-SHP
Screw
CSK M5 X 20 HEX SS
1203390
Screw
CSK M5 X 14 HEX SS
1203389
Screw
CAP M4 X 25 HEX SS
1203391
Nut
M4 SS
1142858
Cover
Door sill
1203396
Page 14
Handle
Screw
Connector
1203354-SHP
Screw
Connector
1203354-SHP
Gasket
1203355-SHP
Gasket
1203355-SHP
Handle
Grub Screw
M5 x 4 Hex
1210530
Grub Screw
M5 x 4 Hex
1210530

CONTACT AND WARRANTY INFORMATION
NEW ZEALAND
KOHLER NZ LTD
- For warranty and other information, please visit our website.
- For contact information, please refer to the Home Owner’s Guide.
Please refer to the Home Owner’s Guide for cleaning instructions.
INSTALLATION INSTRUCTIONSMILANO
TM
Square
CLEANING AND MAINTENANCE INSTRUCTIONS
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
www.englefield.com