Englefield 31258A User manual

PrecautionsHow to useMaintenance Installation Before useOperationCare & Cleaning. Before you call for service Installation
Safety Instructions
Operational Instructions
Name of components
Accessories
2~6
7
8 ~ 10
10
Installation Instructions
Grounding Instructions
Things to be checked after installation
Remote control installation Instruction 16
11 ~ 13
14
15
How to Use Basic Features
How to Use Additional Features
17~18
19 ~ 25
How to take care of this Product
Prevention of Freezing
Flickering Warning Signals
Troubleshooting
Specilcation
Important Safeguards
26 ~ 29
30 ~ 31
31
32~33
34
36
Table of Contents
1349436-A02-C May 2021
INSTALLATION
INSTRUCTIONS
BIDETS
&OHMFlFME
Electronic Bidet Seat Plus
31258A
If you are building a
bathroom from scratch,
giving your bathroom a
makeover or just replacing
an old tap, Englefield can
provide a solution for you.

Prohibited
Di ass sembly
Prohibited
CAUTION
Over 7A
Rating
Usean electric wall outletindependently which is
suitable for AC 240V, rating over7 Ampere.
Use of extension cord or sharing an outlet with other
products may lead to lre or electric shock.
WARNING
Exemption from liability
Safety Instructions
Be sure to observe the following
Failure to observe any of the
following might result in
critical injury or death.
Strictly prohibited.
WARNING Failure to observe any of the
following might result in minor
injury and/or product damage.
CAUTION
Never disassemble or modify this
product.
Proper grounding required to
Never use wet hands.
Be sure to unplug the electric
power plug.
Do not place in or drop into water.
Things that have to be observed.
*1 : Serious injury includes loss of eyesight, severe wound, burn (high, low temperature), electric shock, bone fracture, etc.
*2 : Injury means minor wound, burn or electric shock
*3 : Property damage refers to extensive damage relating to house, furniture, livestock or pets, etc.
.
Be sure to read the following safety instructions carefully and use the product only as instructed in this manual to prevent bodily injuries
and/or property damage which might happen while using this product.
electrical power cord.Do notapply heatto,orplace
heavyobjectson,thecord.
Damaged power cord may lead to re or electrical sho
Do not attempt to replace a damaged power cord on your own.
Contact your nearest authorised service center for
a replacement.
Neverdisassemble,repairor modifytheproduct.
Contact a nearest authorised
service center for repair.
When children, the elderly or the invalid use the
product, the seat temperature adjustment button
should be set to OFF position.
Kids, the elderly, people with sensitive s n, people incapable of
-
inducing medicine (sleeping pill or cold
medicine,etc. or people with hangover
or severe weariness may sustain low
temperatureburnorinjury.
Manufacturer takes no responsibility for any damages resulting from natural disasters such as earthquakes, lightning and wind damage and
mooding, lres not caused by the manufacturer or the bidet product covered by this manual, other accidents, consumer mistakes and/or misuse
and abuse of the product or the use of the product under abnormal conditions.
Manufacturer takes no responsibility for any incidental damages resulting from the use of the product or inability to use the product (lost
prPlts or suspension of business, etc.).
Manufacturer takes no responsibility for any damages resulting from the failure to observe the contents contained in this manual.
2

3
Drain water Prohibited
Usetap water orpotablewateronly.
Usingrecycled water or industrialwatermaycause cystitisor
Irritation to skin.
Do not spray water orwastewater intothe unit orpower plug.
Doing somay cause fire or electric shock.
Keep thepowerplug dust-freebyremoving thedust
usingadry cloth.
When pluggingand unplugging the powerplug, never
use wethands.
Power plug should be plugged into the wall
outlet securely.
Failure to do so may result in electric short circuit,
Smoke generation or ignition.
Prohibited Insert securely
Use tap water Prohibited
Wet hands
prohibited
Wipe off
Do not water the product. Do not install the product
in wet or damp places. (This product is intended for
use on a toilet only, and should not be used for any
Failure to observe may lead to
Disconnect the power plug from the wall outlet and
drain water from water tank in the case that the
product is not used over an
extended period of time.
If not drained, the water may
becomecontaminated.
Never use a damaged power cord, damaged
power plug, or a loose electrical outlet.
Doing so may result in fire, electric shock, short circuit,
Smoke generation or ignition.

Before cleaning the product, always
disconnect the power plug from the
wall outlet.
Failure to do so may result in electric shock
or injury.
Please do notusethe product forusage other
thanthat described in this usermanual.
injury.
Grabthe plug-knobforunplugging the powerplug.
Failure to do so may result in electric shock, electric
Prohibited
Prohibited Prohibited
CAUTION
Safety Precaution
4
Discontinue using the product in case ofmalfunctioning.
Disconnect the power plug from the electrical outlet and close the water
valve if any of the following occur;
Water leaks from either the main unit or the water pipe.
The product makes odd noises or produces unpleasant odour.
Abnormal heat from the main body.
Crack or break on main body.
Fuming from main body.
electric shock or water leakage. Please contact the dealer or an authorised service centre
for repair.
Do not put stove,heater, orcigarettes inor near
theproduct.
Do notrest against theseatcoverwhen
sitting ontheseat.
This may cause the seat cover
to break, which may lead to
back injury if the user loses
his/her balance and tumbles
over.
Disconnect
power plug
Disconnect
power plug

5
Prohibited
Always pressthe panel orremote control button while
theseat is occupied.
Otherwise, the person standing by the product or the
nozzle.
Do notpullforciblyorapply excessiveforce to
thewater feedhose.
Doing so may cause waterto leak.
Select theinstallationplaceto be out ofdirect
sunlight (ultraviolet rays).
Doing so may result in worsening of product surface
suchas discolo ration or fading and/or product
degradation.
warm air outlet ornozzle gate.
Do not spray water,insertlngers orotherobjects into
Doing so may lead to electric shock or product malfunctioning.
Prohibited
warm airblower outlet.
Doing so may result in burn or
injury.
Do notlet a childaloneuse thisproduct.He/shemay
fall into the toiletbowl.
Children being supervised not to play with the
appliance.
CAUTION CAUTION
Close
Prohibited
Prohibited
Do notstand on, or giveashock to,themain
unit.
Doing so may lead to deformation or breakage of the
product, resulting in bodily injury.
Prohibited
Shut offthewatervalve beforeremoving the
Make sure tofasten it upafter thecleaning.
Failure to observe may lead to water leakage.
(See page 27 for cleaning

6
CAUTION
CAUTION
CAUTION
Never place
Never use acidic or alkaline bathroom
Do not throw glowing cigarettes or other
burning materials in the toilet.
Prohibited
detergent, benzene, thinner, cleanser or
nylon scrubber when cleaning the
product. Doing so may damage plastic or
metallic parts.
Do not place or drop the product into
(MPXJOHDJHBSFUUFJTUPCFlYFEJOBDPOTQJDVPVT
place beside the toilet
water. It may lead to a product failure
or electric shock.
%POPUJOTFSUlOHFSTPSPUIFSPCKFDUTJOUP
deodorization cassette housing.
%PJOHTPNBZMFBEUPJOKVSZJOUIFlOHFSTEVFUP
rotating deodorization fan.
Prohibited
Prohibited
WARNING
Use the genuine water lMUFS only. Manufacturer shall not be responsible for any problem
resulting from use of any other filters.
CAUTION for
usage
In the event that the bidet seat is to bereinstalled on a different toilet (ie: product relocation),

Operational Instructions
7
IMPORTANT:
* Connect to mains cold water supply only. Do not connect to hot water supply.
* Water supply pressure for normal operation: Min 220kPa - Max 500kPa.
* 5IJTEPVDIFTFBUJTTVQQMJFEXJUIBMPXNFEJVNIB[BSECBDLmPXQrotection device
complying with AS/NZS 2845.1
*
* This product must be installed with a Ground Fault Circuit Interrupter (GFCI) or a
Residual Current Device (RCD)- see page 14 for electrical grounding instructions.
Do not press the button so hard on the remote control
or panel.
Doing so may cause malfunction.
Water supply to the toilet water tank may be
interrupted if the ball-tap connecting screw is
tightened, when disassembling the water pipe or
connecting water feed hose.
Do not touch ball-tap connecting screw.
Cleansing will stop automatically by the timer after
about 2 minutes of continuous use.
Push the button again if required.
Keep clean the nozzle and warm air blower outlet
against the possible stain from urine
It may cause malfunction.
Have a specialized plumber install the hot water
feed pipe and the flush valve in the cold area.
Contact specialized technician.
Keep the unused water pipes for future use.
Deodorization will stop automatically after 15 minutes
of continuous use.
Please stand up and sit again for longer use.
The main purpose of deodorization is to remove the
odor in toilet bowl. It's not for the whole bathroom.
Do not open/close the toilet seat and cover using
excessive force.
Doing so may lead to breakage or malfunction.
Cleansing water will not flow from nozzle if water
pressure control is set to low in the area of low tap
water pressure.
Please set the water pressure control to "high".
Water may keep running out of nozzle after
cleansing. It does not indicate abnormality. It is
residual water from the inside pipes.
It will stop after 2 minutes.If water runs continually in an
unusual manner, shut off the valve , unplug the power cord and
call the service centre or the dealer.
Drain water completely out of main unit to prevent
possible water leakage and unplug the power cord,
when the product is not in use for a long time.
Wipe up the main unit with a soft cloth when dirty.
Clean with a diluted neutral detergent using soft cloth
and then wipe off with the remaining with damp cloth
if it is excessively dirty.
Keep the nozzle clean against thecontamination.
It may cause bad odor or malfunction.
When the product is operated while the toilet seat is
not occupied be careful as water may splash. This can
occur in the fallowing cases:
- When a child intentionally presses the button
- When a button is pressed during cleaning
- When an object is placed on the remote control.
Replace batteries in the remote controller
periodically. Otherwise, the remote controller
may not properly operate due to weak
batteries.
Never place the remote controller near the stove,
drop or dip into water.
Never drop the remote controller into toilet bowl.
Doing so may lead to malfunction.
Install the remote controller in the place
where the signal can easily reach the signal
receiver.
The remote controller may not operate
properly if things like curtain are in between
the controller(transmitter) and the receiver.
If the direct light or the light from inverter
fluorescent lamp comes in contact with the receiver
of remote controller signal, the remote controller
may not operate properly.
In such case, remove the remote controller from the
holder and use it while holding with the hand.
This product must be installed in accordance with AS/NZS 3500.1, which requires
QSPWJTJPOPGB)JHI)B[BSE#BDLmPX1SFWFOUJPOEFWJDFOPUTVQQMJFE5IJT
requirement is subject to local authority inspection.

13
Installation Instructions
4. Ensure the unit is clear of any packaging etc.
5. Align the center of main unit to the
center of the plate guide and push it all
the way back until you hear a ‘click’ sound.
6. Check that the main unit does not easily
come off by moving the unit in four
different directions.
When the main unit is installed to the toilet
bowl, it may be a little movable, which does
not indicate abnormality. This happens with
the removable type of main unit.
Note
The main unit may become heavily
movable if used over an extended
period of time due to loose bolts. Fully
tighten the bolts if this happens.

14
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric current. This product is equipped with a cord
having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly
JOTUBMMFECZBTVJUBCMZRVBMJlFEFMFDUSJDJBOBOEHSPVOEFE
DANGER - Improper use of the grounding plug can result in a risk of electric shock.
GROUNDED
RCD
TEST RESET
OUTLET
GROUNDED
OUTLET BOX
GROUNDED
PIN
If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either
wolleytuoh htiwrotiw(neergsitahtecafrusretuonagnivahnoitalusnihtiweriwehT.lanimretedalb
stripes) is the grounding wire.
Check with a quali ed electrician or serviceman if the grounding instructions are not completely
understood, or if in doubt as to whether the product is properly grounded.
Grounding Instructions

Things to be checked after installation
15
Operational Check
1. Open mains water supply (Applicable only when closed).
2. Open water feed stop valve.
Check if water leaks from pipe, water tank hose or water feed hose joints.
If water leaks, close the water feed valve, separate the valve and check if rubber packing is
Check if there are any loose connections or joints
before turning on the water valve.
inserted. If not, insert the packing and reassemble the water feed valve.
3. Connect the power plug to the wall outlet.
Nozzle extends and retracts once, and the control panel lamps keep blinking (at initial operation.)
4. Press button on the remote control.
Water pressure/Dry Air lamp goes off when the tank is full of water, and Seat Temperature, Water
Temperature and Water Pressure are set to Low, respectively.
Wait until cleansing water gets warm (takes about 5 minutes).
Check if the seat gets warm, too.
5. Approach hands to sitting sensor (within 5 cm) so that it may be activated.
6. If the tank is full of water, press button one more time and check if the posterior
cleansing system is operating correctly.
Check if nozzle extends and discharges warm water.
(Cover up the nozzle to prevent water from spraying outside.)
7.
deactivate the sitting sensor so that the operation may be stopped.
Cleansing operation stops and nozzle retracts.
Note
If water leaks
Inspection points
1. Open water supply.
1. Close water supply.
2. Open water feed valve and check
2. Disassemble the joint where water is
leaking and connect properly again.
if water leaks from any pipe joints.
If water continues leaking, close water valve and
contact your nearest authorised service center.
Checkforwaterleakage
Checkfor waterleakage from any ofthepipeconnectionsafterinstallation.
5

16
1Insert three AA batteries.
1. Take out the remote controller from the
remote controller holder and open the battery
cover on the back side.
2. Insert three AA batteries (1.5V) while paying
attention to signs.
3. Close the battery cover.
2Install the remote controller on the
wall.
1. Attach the double-stick tape on the back
side of the holder. Red side of the tape
should be visible.
*Once the holder is attached to the wall, it is EJGlDVMU
to remove. Therefore, it is recommended that the
proper location for the remote controller to be
installed should be determined before the holder is
attached on the wall
.
2. Thoroughly clean the area on the wall
where the holder is located, remove the red
cover from the double-stick tape and attach
the holder to the wall.
* Signal can be better received by the receiver if the
remote controller holder is located as close as
possible to the main unit control panel.
3.
Put the remote controller into the holder, press
the dry button on the remote controller while
the sitting sensor is activated and check if the
product operates normally.
*
In the event that the product does not operate normally,
the remote controller holder has to be relocated to
another place where the remote controller normally
operates.
3Put the remote controller into the
holder.
*$IFDLBOEDPOlSNJGUIFSFNPUFDPOUSPMMFSJTQSPQFSMZ
installed in the holder.
How to install the remote control

How to use the basic features
17
Set the Seat Temp control button to “OFF” or “LOW” if the product is used by the following persons:
Young children, the aged or users incapable of setting the temperature themselves.
People with sensitive or irritated skin,
People having taken sleep-inducing medicine such as sleeping pills or cold medicine,
People suffering from hangover or severe physical fatigue.
Failure to do so may lead to the low temperature burn or injury.
WARNING
CAUTION
Note:
- Use three AA size batteries.
- Blinking the means that the batteries need to be replaced.
- If remote control doesn’t work for any reason, use the buttons on the main unit panel.
- LCD display turns on if any button is pressed and turns off 5 seconds after the main unit starts to operate.
- The turbo, cleansing, bidet and auto/child function will not work unless the seat cover is opened and the seat
is occupied.
1:How to set automatic and manual seat and seat cover operation.
Note: The seat cover operation(open/close) is automatic by default.
Automatic:Set seat cover switch on the remote controller to “ON”.
The seat cover will be automatically opened when a person is closer than 70 cm
to the toilet bowl. If nobody is near the toilet bowl within 70cm, the seat
cover will close after approximately 2 minutes.
Note: please ensure that the sensor is never in contact with water.
Caution: If movement of any object or sunray from window is detected
by
sensor, seat cover will be opened.
Manual: Set seat cover switch on the remote controller to “OFF”
***For both settings, manual and automatic:
* Press “SEAT AND COVER” button to open or close * Press “COVER” button to open or close cover.
seat and cover.