Englefield PREMIUM BATH SCREEN User manual

-1-
V087600-K June 08 Kohler Co.
IMPORTANT
READ ALL INSTRUCTIONS CAREFULLY
BEFORE STARTING
THE INSTALLATION
Failure to comply
may void warranty
Bath screens must be installed in situations where the floor of the bathroom has a waterproof membrane installed.
For New Zealand, the bath screen must be installed in accordance with NZBC E3/AS1 clause 3.1.1.
For other countries, the bath screen must be installed in accordance with local building codes.
NOTE:
•A floor waste is recommended.
•Do not install in bathrooms where the floor is carpeted.
INSTALLATION GUIDE
PREMIUM GLASS BATH SCREEN

-2-
V087600-K June 08 Kohler Co.
Parts List - Exploded View

-3-
V087600-K June 08 Kohler Co.
ITEM NO. P ART NO. DESCRIPTION ITEM NO. PART NO. DESCRIPTION
1 Q6080XX Door Hinge Post Retainer 9 Q6334XX Hinge Post Screw Plug
2 Q6090XX Door Hinge Post 10 Q633250 Hinge Post Ajuster S/S
3 Q6150XX Hinge Body 11 Q910100 Screw 8 x 65 Pan Head
4 Q6155XX Hinge Inner 12 Q634045 Seal Door Edge
5 Q633200 Hinge Pad 13 Q634080 Seal Wall
6 Q912325 Screw M8 x 16 14 Q634060 Seal Drip Edge
7 Q616000 Slotted Nylon Bush 15 Q6356XX Top/Bottom Cap Hinge Post
8 Q6338XX Hinge Covers
NOTE: WHEN ORDERING, THE FOLLOWING INFORMATION IS ALWAYS REQUIRED: WIDTH OF ENCLOSURE, COLOUR.
PARTS LIST - BATH SCREEN
Tools required
• Level
• Tape
• Pencil
• Flat blade screwdriver
• Philips screwdriver
• Ruler
• Drill
• Centre-punch
• Hacksaw
• Soft hammer/mallet
• Caulking gun
• Stanley knife
TOOLS AND MATERIALS REQUIRED
The recommended sealants are:
• Sikasil Wet Areas
• Selley Wet Area
• Sika Silaflex RTV (Clear) + primer pen

-4-
V087600-K June 08 Kohler Co.
Ensure Hinge Post Retainer
profile is plumb and ‘T’
stamp is to the top.
Anchor Hinge Post Retainer into
wall stud for maximum support.
CAUTION: BEFORE DRILLING
HOLES ENSURE THERE ARE NO
ELECTRIC CABLES OR WATER
PIPES BEHIND WALLS.
DRILLING INTO THESE CAN
ENDANGER LIFE AND PROPERTY.
Tape over waste outlet.
Bath MUST be installed level.
TIMBER
CONSTRUCTION
SCREW No.8 x 65 mm
BRICK
CONSTRUCTION
SCREW No.8 x 65 mm
6.0mm
NYLON
ANCHOR
BRICK
‘T’ TO TOP
‘T’ TO TOP
3.0mm
WALL STUD
Position Hinge Post retainer central
on top of bath Tiling Bead.
Using a 3mm drill bit, mark position
of holes on wall through extrusion.
Fix with Screw No.8 x 65mm.
Insert Hinge Post over Wall
Retainer and slide down into
position on Bottom Cap.
3.
4.
Set adjusting screws using
6mm spacer provided.
ASSEMBLED UNIT
1.
2.
SILL
CAP
WALL
RETAINER
HINGE POST
L/H SIDE PANEL R/H SIDE PANEL
Fit Bottom Cap to Hinge Post
Retainer.
CAUTION: Fixing the retainer only to
the backboard may void warranty as
a backboard by itself is not able to
provide enough support for the bath
screen.

-5-
V087600-K June 08 Kohler Co.
On the inside of the Hinge
Post, fit slotted plastic bush
through the hole in the glass.
IMPORTANT: ADJUSTMENT
SCREWS MUST BE ADJUSTED IN
SEQUENCE TO AVOID
DISTORTION OF HINGE POST.
Position Door Edge Seal.
DOOR EDGE
SEAL
IMPORTANT: ENSURE BOTTOM
OF DOOR EDGE SEAL IS
CORRECTLY FITTED AS SHOWN.
7.
Position glass by taping the
spacer supplied to the bath as
shown below. Level top of glass
with top cap.
CAUTION: Care must be taken
to avoid cross-threading the
cap screws in the Hinge Plate.
8.
Trim the top of the Door
Edge Seal flush with the
glass.
9.
For “out-of-true” walls, level
Hinge Post using adjusting
screws.
5.
Max 22mm
Max 22mm
6.
Fit Top Cap in place using
silicone and tape down.
10.
Ensure that the slot in
the top bush is vertical
and the slot in the bot-
tom bush is horizontal.
IMPORTANT
Using M8 CSK screw
attach
Inner Hinge Plate.
NOTE: Fix top hinge first.
Tighten screws firmly
to secure glass.
BOTTOM HINGE
TOP HINGE
R/H SIDE PANEL

-6-
V087600-K June 08 Kohler Co.
Position the logo as shown after
door installation. One logo on
the front of the door and one on
the reverse.
HORIZONTAL DIMENSIONS
EQUAL
TOP HINGE
VERTICAL DIMENSIONS EQUAL
IMPORTANT: NOTE ORIENTATION
OF SCREW PLUG HEAD.
MARK SHOULD BE LOCATED TO
SIDE AS SHOWN.
Fit Screw Plugs
Using recommended Sealant,
seal full height between walls
and Wall Retainer Profiles,
and all other exterior joins.
IMPORTANT
SEALANT SHOULD BE APPLIED TO
ALL OUTSIDE JOINTS - DO NOT
SEAL FROM INSIDE.
Attach Door Drip Edge Seal.
11.
Slide on the. four Hinge Covers. 12.
All rights reserved to alter designs and specifications without notice.
WARNING: Products in this leaflet are subject to Industrial Property Protection. All dimensions given are approximate only. ©Copyright Kohler NZ Ltd 2008
LOGO
LOGO
NEW ZEALAND
KOHLER NZ Ltd.
133 Diana Drive,
Glenfield,
Auckland.
CALL US FOR HELP
AUSTRALIA
KOHLER Co.
Unit 10, 79-99 St. Hilliers Road,
Auburn,
Sydney. NSW 2144.
Ph 1300 362 284
Fax [phone]
[e-mail]
www.au.kohler.com
Ph [phone]
Fax [phone]
[e-mail]
www.kohler.co.nz
Follow the sealant manufacturer’s
directions. Some selants may require
the use of a primer.
13.
14.