Entrematic Ditec HA7 Manual

Installation and Service Manual
Swing
Door Operator
Ditec HA7
Trusted brands. Great products.

Entrematic as word and logo are trademarks owned by the Entrematic Group
© Entrematic, 2020
Technical data subject to change without notice.

3
Issue 2020-08-31
1021444-2.0
CONTENTS - Original instructions
1 Revision ..................................................................................................................................................5
2 Instructions for safe operation ......................................................................................................................6
3 Important information ........................................................................................................................... 7
3.1 Intended use ............................................................................................................................................................... 7
3.2 Safety precautions...................................................................................................................................................... 7
3.3 Electronic equipment reception interference .......................................................................................................... 8
3.4 Environmental requirements .................................................................................................................................... 8
4 Technical specifications ..........................................................................................................................9
4.1 Permitted door weight and door width for Ditec HA7 ........................................................................................... 10
5 How the Ditec HA7 works ....................................................................................................................11
5.1 Control switch.................................................................................................................................................. 11
5.1.1 HOLD/AUTO/OFF switch ........................................................................................................................... 11
5.2 Modes and functions on app ................................................................................................................................... 11
5.2.1 Off / Closed ................................................................................................................................................. 11
5.2.2 Exit only...................................................................................................................................................... 11
5.2.3 Auto ................................................................................................................................................... 11
5.2.4 Hold.................................................................................................................................................... 11
5.2.5 Opening ............................................................................................................................................. 11
5.2.6 Closing ............................................................................................................................................... 12
5.2.7 Wireless controlling .......................................................................................................................... 12
5.2.8 Log...................................................................................................................................................... 12
5.2.9 Extended closing torque ................................................................................................................... 12
5.2.10 Power assist ............................................................................................................................................... 12
5.2.11 Push and go ....................................................................................................................................... 12
5.2.12 Function of locks........................................................................................................................................ 12
5.2.13 Impulses............................................................................................................................................. 12
5.2.14 Statistics............................................................................................................................................. 12
5.2.15 Factory reset .............................................................................................................................................. 12
6 Part identification ........................................................................................................................................13
7 Arm systems ................................................................................................................................................15
7.1 Pushing installation with PUSH arm ........................................................................................................................ 15
7.1.1 Drive shaft extension kits forPUSH arm .................................................................................................. 15
7.2 Pulling installation with PULL arm ........................................................................................................................... 16
7.2.1 Drive shaft extension kits for PULL arm ................................................................................................... 16
8 Options.................................................................................................................................................17
8.1 Push plates................................................................................................................................................................ 17
8.1.1 Push plates................................................................................................................................................. 17
8.1.2 Remote transmitter push plates............................................................................................................... 17
8.2 Labels ............................................................................................................................................................... 18
9 Pre-installation .....................................................................................................................................19
9.1 General tips/Safety concerns................................................................................................................................... 19
9.2 Installation examples ...................................................................................................................................... 20
9.3 Fastening requirements (but not included) ................................................................................................... 20
10 Mechanical installation................................................................................................................................21
10.1 PUSH arm system ..................................................................................................................................................... 21
10.2 PULL arm system ...................................................................................................................................................... 28
11 Electrical connection ............................................................................................................................35
11.1 Mains connection..................................................................................................................................................... 35
11.2 Control unit (CU).............................................................................................................................................. 37
12 Start-up ................................................................................................................................................38
12.1 Spring pre-tension........................................................................................................................................... 38

4 Issue 2020-08-31
1021444-2.0
12.2 App ...................................................................................................................................................................39
12.2.1 Install the app. ........................................................................................................................................... 39
12.2.2 Log in to the app with owner ............................................................................................................39
12.2.3 Learn .......................................................................................................................................................... 40
12.2.4 Test ............................................................................................................................................................................... 41
12.2.5 Settings ..............................................................................................................................................41
12.2.6 Add user..................................................................................................................................................... 42
12.2.7 Remove user ............................................................................................................................................... 42
12.2.8 Log into the app with user .......................................................................................................................... 43
12.2.9 Configuration parameters ........................................................................................................................ 44
13 Cover ................................................................................................................................................... 45
14 Troubleshooting .................................................................................................................................. 46
15 ANSI / BHMA A156.19 (LOWENERGY APPLICATION) .................................................................................. 47
15.1 REQUIREMENTS FOR POWER OPERATED DOORS .................................................................................................. 47
15.1.1 Activation...........................................................................................................................................47
15.1.2 Opening..............................................................................................................................................47
15.1.3 Closing ................................................................................................................................................47
15.1.4 Force and Kinetic Energy........................................................................................................................... 47
15.1.5 Signage............................................................................................................................................... 48

1 Revision
5
Issue 2020-08-31
1021444-2.0
1 Revision
Following pages have been revised:
Page Revision
9,10
Changed weight notes
21, 25
Changed fastener specifications
39, 43
Changed app images
44
Changed configuration parameters

6 Issue 2020-08-31
1021444-2.0
2 Instructions for safe operation
2 Instructions for safe operation
• Failure to observe the information in this manual may result in
personal injury or damage toequipment.
• To reduce the risk of injury to persons - use this operator with single
swinging only.
• Do not use the equipment if repair or adjustment is necessary.
• Disconnect power when cleaning or other maintenance is to be
carried out.
• The operator can be used by children only when supervised by a
person responsible for their safety
.
• The operator can be used by persons with impaired physical, sensory
or mental capacity if they have been instructed by a person in charge
of their safety.
• Cleaning and user maintenance shall not be made by children.
• Do not let anyone climb on or play with the door or the fixed/remote
controls.
• In all instances, where work is being done, the area is to be secured
from pedestrian traffic, and the power removed to prevent injury.
• The doorset can be operated automatically or manually by
activators. It can also be used manually as a door closer.

3 Important information
7
Issue 2020-08-31
1021444-2.0
3 Important information
3.1 Intended use
The Ditec HA7 is an automatic swing door operator developed to facilitate interior entrances to
buildings and within buildings through swing doors. The Ditec HA7 is an electromechanical
operator approved for fire door applications. It is to be installed indoors where it is suitable for
almost all types of internal swing doors. This widely-used operator can be found in applications
ranging from handicapped-access in private homes to commercialestablishments.
Door operator used in escape routes shall be installed so that the door opens in the escape direction
unless the system allows break-out in this direction.
The motor and gear box are combined into a compact unit mounted alongside the control unit
within the cover. The operator is connected to the door leaf with arm systems.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and
to minor friction changes caused by e.g. dust and dirt.
For escape in emergency situations the doorset is opened manually.
This manual contains the necessary details and instructions for the installation, maintenance and
service of the Swing Door Operators Ditec HA7.
Make sure that the connection to the source of supply by a flexible cord shall not be allowed to
become entrapped in moving parts of the operator or door system.
The glazing material in unframed swinging doors and/or framed swinging doors except that glazing
material is less than 1 ft
2
(0.9 m
2
) and having no dimension greater than 18" (457 mm) shall be
comply with the requirements of ANSIZ97.1.
Please use the adaptor provided with the operator in the packaging, other adaptor may result in
risk of fire.
For use see User manual 1020879 .
Save these instructions for future reference.
3.2 Safety precautions
To avoid bodily injury, material damage and malfunction of the product, the instructions contained
in this manual must be strictly observed during installation, adjustment, repairs and service etc.
Factory authorized training is required to carry out these tasks safely. Only Entrematic-trained
technicians should be allowed to carry out these operations.

3 Important information
8
Issue 2020-08-31
1021444-2.0
3.3 Electronic equipment reception interference
The equipment generates and uses radio frequency energy and if not installed and used properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements, interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Re-orient the antenna.
• Relocate the receiver with respect to the equipment.
• Move the receiver away from the equipment.
• Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
• Check that protective earth (PE) is connected.
If necessary, the user should consult the dealer or an experienced electronics technician for additional
suggestions.
3.4 Environmental requirements
Entrematic products are equipped with electronics and may also be equipped with batteries
containing materials which are hazardous to the environment. Disconnect power before
removing electronics and battery and make sure it is disposed of properly according to local
regulations (how and where) as was done with the packaging material.

4 Technicalspecifications
9
Issue 2020-08-31
1021444-2.0
4 Technical specifications
Ensure that the door operator with technical specification below is suitable for the installation.
Manufacturer: Entrematic
Address: 221A Racco Parkway Vaughan Canada
Type: Ditec HA7
Power supply: 120VAC+10/-15%,50/60 Hz,mains fusemax10A(building
installation)
Power consumption: Max. 90 W
Auxiliary voltage: 24 V DC, max. 400 mA (max. 1000 mA including lock)
Max. weight/width: 200 Lbs.
Note! Refer to section 4.1 and the appropriate standard
(ANSI/BHMA A156.19) for door forces and speeds as related to
door weight and width.
Door width: 762 - 1219 mm (30 - 48”)
Electro-mechanical locking
device:
Selectable: 12V DC, max. 1200 mA or 24 V DC, max. 600 mA
Door opening angle: PUSH arm: 80° - 110°, with reveal 0 - 130 mm (0 - 5 1/8")
PULL arm: 80° - 110°, with reveal 0 - 51 mm (0 - 2")
Opening time (0° - 80°):
Variable between 4.5 - 9 s
Closing time (90° - 10°): Variable between 4.5 - 9 s
Impulse time delay: 2 s - 6 h
Ambient temperature: -4 °F to +113 °F (-20 °C to +45 °C)
Relative humidity: Max. 95%
Drive unit weight: 7.5 lb. (3.4 kg)
Class of protection: IP20
Approvals: Third party approvals from established certification organizations
valid for safety in use, see Declaration of Conformity.
Complies with: UL 10C, ANSI/BHMA A156.19 and UL 325

4 Technicalspecifications
10
Issue 2020-08-31
1021444-2.0
This product is to be installed internally.
4.1 Permitted door weight and door width for Ditec HA7:
Push arm: 150 Lbs. / 48" or 266 Lbs. / 36"
Pull arm: 112 Lbs. / 48" or 200 Lbs. / 36"
Note: Complies with UL 325.

5 How the Ditec HA7 works
11
Issue 2020-08-31
1021444-2.0
5 How the Ditec HA7 works
The swing door operator Ditec HA7 uses a motor which is connected to the output shaft. The
push or pull arm system that is connected to the output shaft opens the door in a surface
mounted application.
5.1 Control switch
5.1.1 HOLD/AUTO/OFF switch
Function Program
HOLD The door can be held at any position when opening or closing.
AUTO
Impulses from activation units connected to IIMP or OIMP are forwarded into inner
impulse.
OFF Only KEY Impulse can open the door.
5.2 Modes and functions on app
5.2.1 Off / Closed
The door is closed. The door cannot be opened with the inner / outer wall or jamb-mounted contact
switches. The door is locked if an electromechanical locking device has been fitted.
5.2.2 Exit only
Passage from inside only. The door is normally locked if an electromechanical locking device has
been fitted. The door can only be opened with the inner wall or jamb-mounted contact switches
(if fitted).
5.2.3 Auto
The door can be opened with the inner / outer wall or jamb-mounted contact switches.
5.2.4 Hold
The door can be held at any position when opening or closing.
5.2.5 Opening
When an opening signal is received by the control unit, the door is opened at the operator-adjusted
opening speed. Before the door is fully open at back check, it slows automatically to low speed.
The motor stops when the selected door opening angle has been reached. The open position is
held by the motor.
If the door is obstructed while opening, it will stop on stall which can be selected with the app (see
page 35).

5 How the Ditec HA7 works
12
Issue 2020-08-31
1021444-2.0
5.2.6 Closing
When the hold open time has elapsed, the operator will close the door automatically, using spring
force and motor. The door will slow to low speed at latch check before it reaches the fully closed
position. The door is kept closed by spring power or combined with extended closing torque by
the motor.
5.2.7 Wireless controlling
The door can be controlled by the app on a smartphone or a tablet.
5.2.8 Log
Events and errors can be displayed.
5.2.9 Extended closing torque
The motor will increase the closing torque when the door is closed or during closing. If the para-
meter is set to "0", the door will close with normal spring power.
5.2.10 Power assist
The motor will give/increase power assist when the door is opened manually. If the parameter is
set to "Off", the door will give no power assist.
5.2.11 Push and go
When the door is manually pushed it will perform an open / close cycle. Push and go is not active
in mode "Off/Closed".
5.2.12 Function of locks
• The control unit has an available output of DC for external locks
• The lock output is short circuit proof and can supply a lock with 12 V DC, max. 1200 mA or 24
V DC, max. 600 mA. Lock function is active in mode "Off / Closed" and "Exit Only".
• Select 12 V DC or 24 V DC, locked with or without power
• Lock release and opening delay
• Lock kick to overcome binding in the locking device during closing
5.2.13 Impulses
• Input for INNER / OUTER / KEYimpulse.
5.2.14 Statistics
• Record data of the action for the door.
5.2.15 Factory reset
• Will restore all settings with factory default settings.

6 Part identification
13
Issue 2020-08-31
1021444-2.0
6 Part identification

6 Part identification
14
Issue 2020-08-31
1021444-2.0
Item
No.
Art. No. Description
1
W7-331020157
Ground wire
2 W7-330000828 Back plate with power cable
3
W7-331020445BK
Spindle cover kit (Black)
W7-331020445PD
Spindle cover kit (Grey)
4
W7-331019785
Bracket power plug
5 W7-331020704BK Endplate with control switch (Black)
6
W7-331020393BK
Endplate (Black)
7 W7-331018537 Control unit (CU)
8
W7-330000841
Transmission unit kit
9 W7-330000829 Lock kick for PUSH & PULL
10
W7-331020253
Adaptor holder
11 W7-331704236 Extension power cable
12
W7-331020396DB
Cover (Black)
W7-331020396NA
Cover (Silver)
13
W7-331018859
Power cord
14 W7-331703711 Power adaptor
15
W7-331020293
Power box adaptor kit (internal components only, box not included)
16
W7-330000830BK
PULL arm service kit (Black)
W7-330000830PD
PULL arm service kit (Grey)
17 W7-331020226BK PULL arm kit (Black)
W7-331020226PD
PULL arm kit (Grey)
18 W7-331020857BK PUSH arm kit (Black)
W7-331020857PD
PUSH arm kit (Grey)
19 W7-330000831BK Drive shaft kits for PUSH arm (Black)
20
W7-330000832BK
Drive shaft kits for PULL arm (Black)

7 Arm systems
15
Issue 2020-08-31
1021444-2.0
7 Arm systems
7.1 Pushing installation with PUSH arm
Reveal
Part No.: 0 - 68mm (0 - 2 11/16")
Part No.: 56 - 130mm (2 1/4 - 5 1/8")
7.1.1 Drive shaft extension kits for PUSH arm
35mm (1 3/8”)
20mm (3/4”)
Part No.: H-W7-1020924

7 Arm systems
16
Issue 2020-08-31
1021444-2.0
7.2 Pulling installation with PULL arm
Part No.: W7-331020226BK
7.2.1 Drive shaft extension kits for PULL arm
43mm (1 3/4”)
28mm (1 1/8”)
Part No.: H-W7-1020925

8 Options
17
Issue 2020-08-31
1021444-2.0
8 Options
8.1 Push plates
For ADA compliance, center of push plate(s) must be 34"-48" above finished floor or height required
by local AHJ.
8.1.1 Push plates
P/N: W6-115 P/N: W6-124-1
P/N: W6-110 P/N: W6-110-2 P/N: W6-105
8.1.2 Remote transmitter push plates
P/N: W6-114 P/N: P-CM-45/4
PRESS
TO OPEN
PRESS
TO OPEN
PUSH
TO
TO OPEN

8 Options
18
Issue 2020-08-31
1021444-2.0
No. 1020654
8.2 Labels
PUSH TO
ACTIVATE
PULL TO
ACTIVATE
Push side “PUSH TO ACTIVATE” Pull side “PULL TO ACTIVATE”
ACTIVATE
SWITCH TO
OPERATE
Dual Side “Activate Switch to Operate” Dual Side “AUTOMATIC DOOR / CAUTION”
ANNUAL COMPLIANCE
INSPECTION
Inspected for and complies
with
ANSI A156.
DATE:
by AAADM Certified
Inspector
Number:
#US24-0542-01
"Certified Inspector" "AAADM safety"

9 Pre-installation
19
Issue 2020-08-31
1021444-2.0
9 Pre-installation
9.1 General tips/Safety concerns
In all instances, where work is being done, the area is to be secured from
pedestrian traffic, and the power removed to prevent injury.
• Make sure that the power is off before installing.
• If there are sharp edges after drilling the cable outlets, chamfer the edges to avoid damage to
the cables.
• For enhanced security and vandalism protection, always mount the operator access in the
interior of a building wheneverpossible.
• Make sure the ambient temperature is in the range specified in section Technical specifications.
• Make sure that the door leaf and the wall are properly reinforced at the installation points.
• Unpack the operator and make sure that all parts are delivered in accordance with the packing
note and that the operator is in good mechanical condition.
• Ensure proper material is being used for the door leaves and that there are no sharp edges.
Projecting parts shall not create any potential hazards. If glass is used bare glass edges shall not
come in contact with other glass. Toughened or laminated glass are suitable glasses.
• Ensure that entrapment between the driven part and the surrounding fixed parts due to the
opening movement of the driven part is avoided. The following distances are considered sufficient
to avoid entrapments for the parts of the body identified;
- for fingers, a distance greater than 25 mm (15/16") or less than 8 mm (5/16")
- for feet, a distance greater than 50 mm (1 15/16")
- for heads, a distance greater than 200 mm (7 7/8")
- and for the whole body, a distance greater than 500 mm
• Danger points shall be safe guarded up to a height of 2.5 m (98 7/16") from the floor level.
• The operator shall not be used with a offset pivot door.

9 Pre-installation
20
Issue 2020-08-31
1021444-2.0
9.2 Installation examples
1 Aluminum profile system
2 Plasterboard wall
3 Reinforced concrete wall and brick wall
4 Plasterboard wall
A Steel reinforcement or rivet nut
B Wood reinforcement
C Expansion-shell bolt (for brick wall min. M6x85,
UPAT PSEA B10/25)
9.3 Fastening requirements (but notincluded)
Base material
Steel
Aluminum
Reinforced concrete
Wood
Brick wall
Minimum requirements of wall profile*
5mm (3/16")**
6mm (1/4")***
min. 50mm (2") from the underside
50 mm (2")
Expansion-shell bolt, min. M6x85, UPAT PSEA B10/25, min. 50mm (2")
from the underside
* Entrematic minimum recommended requirements. Building Codes may give different specifications.
** Thinner wall profiles (3-5 mm) must be reinforced with rivet nuts.
*** Thinner wall profiles (4-6 mm) must be reinforced with rivet nuts.