Entrematic EMSL User manual

Sliding Door Operator
EM SL
User Manual
Original instructions

CONTENTS - Original instructions
4Instructions for safe operation .......................................................................................................
5Congratulations on your new automatic door! ........................................................................
5Electronic equipment reception interference ...........................................................................
5Environmental requirements ..........................................................................................................
5Product liability ...................................................................................................................................
6Service .....................................................................................................................................................
6Intended use .........................................................................................................................................
6.........................................................................................................................................
6Technical specification ......................................................................................................................
7How the EM SL works ........................................................................................................................
7Locking ....................................................................................................................................................
7Unlocking ...............................................................................................................................................
8Programme selectors .........................................................................................................................
8Programme selector functions .............................................................................
9Integrated safety ..................................................................................................................................
9Safety system with presence sensors ..........................................................................................
9Technologically advanced sensors ................................................................................................
10
How to check your inner and outer combined motion and presence
detection sensors ......................................................................................................
11How to check your side presence detector(s) ................................................
12Emergency escape ..............................................................................................................................
12Break-out unit PSB ....................................................................................................
12Electrical emergency unit (EEU) ..........................................................................
13Regular safety checks .........................................................................................................................
15Safety accessories ................................................................................................................................
16General accessories ............................................................................................................................
16Cover .............................................................................................................................
16Motion sensor and presence sensors .................................................................
16Programme selectors ...............................................................................................
16Electrical locks ............................................................................................................
16Manual unlocking device ........................................................................................
16Micro switch kit, LSK/LIS .........................................................................................
16Locked door indicator, LDI/LIS ..............................................................................
16Electrical emergency unit with batteries ..........................................................
16Electrical emergency unit with batteries and two motors ..........................
1005274-EMen-9.0Issue 2019-06-282

17Emergency closing with repeated closing ........................................................
17Break-out unit PSB ....................................................................................................
17Interlocking .................................................................................................................
17Convenience battery UPS .......................................................................................
17External error indication .........................................................................................
17Key switches (flush and/or surface mounted) .................................................
17Push button ................................................................................................................
17Double carriage wheels ..........................................................................................
17Emergency opening .................................................................................................
17Synchronization ........................................................................................................
18Troubleshooting ..................................................................................................................................
19Service/Maintenance .........................................................................................................................
19Other products from Entrematic Group .....................................................................................
20Declaration of conformity ................................................................................................................
© All rights in and to this material are the sole property of Entrematic Group AB. Copying, scanning, alterations
or modifications are expressly forbidden without the prior written consent of Entrematic Group AB. Rights
reserved for changes without prior notice.
Backtrack information: folder:Workspace Main, version:a542, Date:2019-06-27 time:12:11:27, state: Frozen
3Issue 2019-06-281005274-EMen-9.0

Instructions for safe operation
•Failure to observe the information in this manual may
result in personal injury or damage to equipment.
•To reduce the risk of injury of persons - use this oper-
ator only with pedestrian doors.
•Do not use the equipment if repair or adjustment is
necessary.
•Disconnect supply when cleaning or other mainten-
ance is to be carried out.
•The operator can be used by children over 8 years of
age if they have been instructed by a person in charge
of their safety.
•The operator can be used by children 8 years of age
or younger if they are supervised by a person respons-
ible for their safety.
•The operator can be used by persons with impaired
physical, sensory or mental capacity if they have been
instructed by a person in charge of their safety.
•Cleaning and user maintenance shall not be made by
children.
•Do not let anyone climb on or play with the door or
the fixed/remote controls.
•The doorset can be operated automatically by sensors
or manually by activators.
1005274-EMen-9.0Issue 2019-06-284

Congratulations on your new automatic door!
Entrematic Group AB has developed automatic doors for more than 50 years. State-of-the-art tech-
nology and carefully tested materials and components provide you with a superior product.
As with all other technical products, your automatic door requires periodic maintenance and service.
It is essential that you know your automatic door (system) and that you recognize the importance
of maintaining it in compliance with applicable standards for safety.
Your local Entrematic Group-authorized representative is familiar with these standards, as well as
all applicable local codes and Entrematic Group recommendations for power-operated pedestrian
doors. Service and adjustments performed by your Entrematic Group-authorized representative,
will ensure safe and proper operation of your automatic door unit.
Electronic equipment reception interference
The equipment may generate and use radio frequency energy and if not installed and used properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•Re-orient the receiving antenna.
•Relocate the receiver with respect to the equipment.
•Move the receiver away from the equipment.
•Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
•Check that protective earth (PE) is connected.
If necessary, the user should consult the dealer or an experienced electronics technician for additional
suggestions.
Environmental requirements
Entrematic Group products are equipped with electronics and may also be equipped with batteries
containing materials which are hazardous to the environment. Disconnect power before removing
electronics and battery and make sure it is disposed of properly according to local regulations (how
and where) as was done with the packaging material.
Product liability
According to regulations, the following are the responsibility of the owner or caretaker of the
equipment
•that the equipment operates correctly, so that it gives sufficient protection in regard to safety
and health
•that the equipment is operated and regularly maintained, inspected and serviced by someone
with documented competence in the equipment and in applicable regulations
•that the provided “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
are kept available for maintenance and service records
•that inspection covers the emergency opening function (when applicable)
•that the closing force is appropriate for the door size on fire-approved door systems (when ap-
plicable)
5Issue 2019-06-281005274-EMen-9.0

Service
Inspections should be done regularly by a trained and qualified person. The frequency of these in-
spections should be according to national regulations (or according to industry standard if there
are no national regulations). This is especially important when the installation concerns a fire-ap-
proved door or a door with an emergency-opening function. To extend the life of your investment
and ensure safe and reliable operation of the door, we recommend a minimum of 2 visits per year
or more, depending on usage and operating conditions. Environmental aspects shall also be con-
sidered.
Talk to your Entrematic Group representative to learn more about our service offering.
Intended use
The EM SL is an automatic sliding door operator developed to facilitate entrances to buildings and
within buildings through sliding doors.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and to
minor friction changes caused by e.g. dust and dirt.
In emergency situations the doorset is opened and remains open automatically. It may also be
equipped with break-out function, in which case the door leaf is pushed manually open in the escape
direction.
Dual batteries and motors are used in escape routes as indicated in associated certificates. See
"Electrical emergency unit with batteries" on page 16 and "Electrical emergency unit with batteries
and two motors" on page 16. For manual break-out see "Break-out unit PSB" on page 17.
It is to be used indoors where it is suitable for almost all types of external and internal sliding doors.
Ensure that the lock is only activated when there are no persons in the room.
For installation and maintenance see Installation and Service manual 1004572.
Save these instructions for future reference.
Technical specification
Entrematic Group ABManufacturer:
Lodjursgatan 10, SE-261 44 Landskrona, SwedenAddress:
EM SLType:
120 - 240 V AC 50/60 Hz, mains fuse max 10AMains power supply:
Max. 250 WPower consumption:
IP20Degree of protection:
Sound pressure:
Third party approvals from established certification organizations valid
for safety in use, see Declaration of Conformity.
Approvals:
1005274-EMen-9.0Issue 2019-06-286

How the EM SL works
The EM SL works electromechanically. The drive unit, control unit, transmission, optional emergency
unit and electromechanical locking device are all assembled in a support beam with an integrated
cover. The motor and gear box transmit movement to the door leaves by means of a tooth belt. The
door leaf is fitted to a door adapter/carriage and hangs on a sliding track. The active leaf travel is
directed by a floor guide.
When an opening impulse (e.g. from a motion sensor) is received by the control unit, the drive unit
starts and transmits movement to the door leaves to open.
The closing starts when no OPENING IMPULSE is received, the HOLD OPEN TIME has ended and no
PRESENCE IMPULSE is activated.
The EM SL user can select five different modes of operation if a programme selector is installed. See
Programme selectors on page 8.
Locking
Doors used for emergency escape in buildings such as hospitals and homes for elderly people may
not be locked or put in mode selection OFF mode. In other buildings emergency escape doors may
be locked or put in mode selection OFF mode after it has been secured and all people have left the
building.
Unlocking
Unlock all the mechanical locks before activating the operator.
7Issue 2019-06-281005274-EMen-9.0

Programme selectors
The door functions are set with different key programme selectors. The key must always be removed
on emergency escape doors after changing settings.
Surface mounted
PS-6
PSMB-5
PS-5M
Flush mounted
Programme selector functions
This function is only used on emergency escape doors after it is certain
that all people have left the building.
The door cannot be opened with inner and outer activation units. The
door is locked if an electromechanical locking device has been fitted. The
door can be opened partially with a key switch (if fitted). With an emer-
gency push-button (if fitted) the door opens fully.
OFF
Passage from inside only. The door is normally locked if an electromech-
anical locking device has been fitted. The door can only be opened with
the inner activation unit or with a key switch/emergency push-button (if
fitted).
EXIT
Two-way traffic, normal operation of the door. The door can be opened
with the inner and outer activation units and with a key switch/emergency
push-button (if fitted).
AUTO
Two-way traffic, AUTO PARTIAL is obtained. The door can be opened
partially with the inner and outer activation units and with a key switch
(if fitted). With an emergency push-button the door opens fully.
AUTO
PARTIAL
The door is permanently open. The door can be moved by hand e.g. for
window cleaning. All activation units except for the emergency push
button (if fitted) are disconnected.
OPEN
Set the programme selector to AUTO. Insert a narrow object in the small
hole on the programme selector and push briefly. The operator makes a
system test of the emergency unit (if selected), electromechanical lock,
watchdog relay and closed door position. The operator is after closing
reset and ready for normal operation.
RESET
Note! The RESET is not available on programme selector PS-5M.
Turn the key clockwise to the position “R”(six o’clock) and insert a narrow
object in the small hole on the programme selector and push briefly. Then
turn the key counter-clockwise back to the requested setting. The oper-
ator makes a system test of the emergency unit (if selected), electromech-
anical lock, watchdog relay and closed door position. The operator is after
closing reset and ready for normal operation.
RESET
Note! The key cannot be removed in the "R" position.
Note! If monitored emergency unit is a demand, a test of the emergency unit is performed when
the programme selector is turned from OFF or OPEN to any other position.
1005274-EMen-9.0Issue 2019-06-288

Integrated safety
To permit a safe passage between closing doors, the doors reverse immediately if an obstruction is
detected. They then resume their interrupted movement at low speed to check whether the obstruc-
tion has disappeared or not.
If an obstruction is detected while the door is opening, the doors stop immediately, and then close
after a time delay.
Safety system with presence sensors
Usually the safety system incorporates presence sensors installed above the door opening. A presence
sensor detects an object in the doorway, while the doors are closing, the doors reverse immediately.
The doors will start to close when the object is removed.
Technologically advanced sensors
The Entrematic Group sensors have been tested and approved by the Entrematic Group test labor-
atory for use on Entrematic Group's automatic sliding doors. These presence sensors further improve
the already high obstruction detection obtained with the built in self-monitored crush force limitation.
Monitored sensors have built-in monitoring for error detection.
Note! If you have a problem you cannot correct, turn off the automatic door immediately and call
your Entrematic Group service representative for assistance.
9Issue 2019-06-281005274-EMen-9.0

How to check your inner and outer combined motion and presence detection
sensors
Combined sensors are used when you want both a motion sensor and a presence sensor integrated
into the same unit.
1 Walk towards the door opening, the door shall start to open when you are about 1.5 meter from
the door and the door shall stop in open position.
2 When the door has closed, repeat the same procedure from the other side of the door opening.
3 Open the door, stand still close to the face of the open door leaf on the left side for more than
5 s. The door shall remain open. Repeat on the right side.
4 Repeat step 3 in the other side of the door opening.
1005274-EMen-9.0Issue 2019-06-2810

How to check your side presence detector(s)
Side presence sensors can be used for example if higher door speed is required or for installations
in homes for elderly/disabled or childcare centres, to protect users from being struck by the doors
during their opening cycle. When a side presence sensor detects an obstacle the door operator will
not stop, but slow down the door movement to a safe speed. With this safe speed the door will try
to push the obstruction away, to ensure that the person passing through the door will not walk into
the door.
Walk into the detection field of the side presence sensor on one side. Activate the impulse on the
operator, the door shall not stop, but slow down to safe speed during the opening.
If you have a bi-parting (double) door then repeat the procedure above on the other side.
11Issue 2019-06-281005274-EMen-9.0

Emergency escape
The operator can be fitted with different emergency escape units to ensure a safe evacuation of the
building.
Break-out unit PSB
The door leaves and the side screens are swung outwards when a defined pressure is applied.
The break-out function can also be used to create a wider opening. From the fully swung out position,
the door leaves can be manually slid sideways, offering the possibility to transport wide objects
through the opening, or to make a shop entrance more inviting during good weather.
Electrical emergency unit (EEU)
The door is opened by means of a rechargeable battery unit in the event of a power failure. The door
remains in this position until the power is restored. The operator will then resume the function set
by the mode selector. The emergency unit is monitored by the operator control unit. A monitoring
error is indicated by flashing red LED on the operation mode selector (OMS) and the door remains
in open position until the error is cleared.
For further information, see General accessories on page 16.
The electrical emergency function can also be used to close the door in the event of power failure.
The fire authorities make this a requirement to stop fire or smoke from spreading throughout the
building.
1005274-EMen-9.0Issue 2019-06-2812

Regular safety checks
To help you fulfil the national/international requirements and to avoid malfunction and risk for in-
juries, we have provided the following checklist.
Do not use the operator if repair or adjustment is necessary.
Disconnect supply when cleaning or other maintenance is to be carried out.
If problem
occurs
Daily Action
Activate your operator and visually check, fastening of
•operator and cover
•cables
•programme selector(s)
•door and glass (stability)
Also inspect your operator and check visually for
•condition of door seals and weather stripping
•condition of glazing rubbers
•finger protection
•proper operation; closes slowly and smoothly
•any ventilation being obstructed
Set the programme selector to OFF and check that the operator and electromechanical lock (if fitted)
work together. Also check that the lock really secures the door.
Activate the manual activation units , if any, and walk towards the door. Check that the door has
opened appropriately while you pass the entrance/exit.
Then proceed with the automatic activation units in the same way.
Check the safety sensors if any.
If you are unsure of which type of sensor you have, please contact your Entrematic Group repres-
entative.
If the operator is equipped with break-out system, set the mode selector to
AUTO mode. Push the door manually while in the escape direction to ensure
that nothing prevents the door from being open. Also ensure that the escape
route is free for use. After the test, restore the door(s) to their normal mode
of operation.
By law, these tests must be performed regularly by trained personnel.
Escape
doors
If the operator is equipped with automatic opening system, shut off the
power and the door should open and remain open. Restore power and the
door should close.
Let the door close after an impulse ensuring nothing prevents the door from
closing and locking (if regulations require it).
Fire
doors
Take appropriate measures.=
Contact your Entrematic Group representative. For contact information, see last page.=
13Issue 2019-06-281005274-EMen-9.0

FUNCTION AND VISUAL INSPECTION
CLEANING
The best way to remove dust and dirt from the EM SL is to use water and a soft cloth or a sponge.
A gentle detergent may be used. To maintain the quality of the surface treatment, the surfaces should be cleaned
once/four months period. The cleaning should be documented. To avoid damages to the profiles the
brushes/weather stripping must be vacuum-cleaned weekly.
•Do not expose windows, doors or profiles to alkalis. Both aluminium and glass are sensitive to alkalis.
•Do not clean with high pressure water. Operator, mode selector and sensor may be damaged and water
may enter the profiles.
•Do not use polishing detergent.
•Do not scrub with materials like Scotch-brite, as this will cause mechanical damage.
1005274-EMen-9.0Issue 2019-06-2814

SIGNAGE
Action
Check that all required signage is applied and intact. Mandatory indicates that the signage is required by European
directives and equivalent national legislation outside the European Union.
Product label: Mandatory
Emergency break-out: Mandatory, if approved for escape route.
Entrematic Group door sticker: Mandatory, if applicable to highlight the presence of the glass (applied to
all glass sections that are moving).
Supervision of child (applied to both sides of the door): Mandatory according to national regulations.
Recommended, if the risk analysis shows use by children.
Operator designed for disabled people:
Recommended, if applicable (applied to both sides of the door).
Activation by disabled people: Recommended, if applicable.
No entry, identifying one-way traffic: Mandatory in GB and US, if applicable, not included in the product.
Local product label
Keep clear
Automatic door
Safety accessories
Even though the EM SL is installed to comply with all applicable safety regulations, it is possible to
enhance safety/comfort with the following add-ons (please contact your local Entrematic Group
company for detailed description).
•Combined motion and presence sensors
•Separate presence sensors (presence in the door opening or side presence for the trailing edge
of the door)
15Issue 2019-06-281005274-EMen-9.0

General accessories
Your EM SL can be further improved with the following add-ons (please contact your local Entrematic
Group dealer for detailed description).
Cover
Made in clear anodized aluminium as standard. Paint finished in RAL colours or anodizing optional.
Motion sensor and presence sensors
Add motion and presence sensors to improve comfort and safety.
Programme selectors
See page 8.
Electrical locks
The following locks are available to the operator:
•Locked with power (LDP), fail safe
•Locked without power (LD), fail secure
•Bistable lock (LDB)
Manual unlocking device
For manual unlocking of the electrical lock, locked without power.
Micro switch kit, LSK/LIS
For indication of door and lock position.
Locked door indicator, LDI/LIS
For indication of locked lock and closed door for connection to alarm system.
Electrical emergency unit with batteries
Used if a door is required to be opened or closed by means of a rechargeable battery unit and remain
in this position in the event of power failure. Authorities can demand that the emergency units are
monitored on a regular time basis. Half an hour before this time has elapsed the following opening
impulse generates an emergency opening test. If there is no opening impulse within the next half
hour, the operator control unit generates the opening impulse itself.
If the battery opens the door within the limited time the test is successful and the door resumes the
function set by the programme selector.
Note! The test is never performed in programme selector setting OPEN. In setting OFF it can be se-
lected. The test is always performed after a RESET and after changing program selection, from a pos-
ition where a test is not done to a position where the test is a demand.
Electrical emergency unit with batteries and two motors
Used if a door is required to be opened by means of a rechargeable battery unit and remain in this
position in the event of power failure. Authorities can demand that the emergency unit is monitored
on a regular time basis. Half an hour before this time has elapsed the following opening impulse
generates an emergency opening test. If there is no opening impulse within half an hour, the oper-
ator control unit generates the opening impulse itself.
If the battery opens the door within the limited time the test is successful and the door resumes the
function set by the programme selector.
Note! The test is never performed in programme selector setting OPEN. In setting OFF it can be se-
lected. The test is always performed after a RESET and after changing program selection, from a pos-
ition where a test is not done to a position where the test is a demand.
1005274-EMen-9.0Issue 2019-06-2816

Emergency closing with repeated closing
If the door is opened by hand after an electrical emergency closing, it will close again.
Break-out unit PSB
Enables door/side screens to be broken outwards in case of emergency.
See page 13.
Interlocking
Used between two operators when the first operator must close before the other one can open
(typical to reduce energy losses and not for security reasons). EXU-4 required.
Convenience battery UPS
Stand-by supply which gives continued operation during short power failure. EXU-3 or EXU-4 required.
External error indication
Obtained if a lamp or a buzzer is connected. EXU-4 required.
Key switches (flush and/or surface mounted)
Used to give opening impulse to the door in any programme selector setting.
The key switch can also open the door when power is switched off, if a battery is fitted.
Push button
Used to give opening impulse to the door.
Double carriage wheels
Used for door weights over 100 kg and for narrow door leaves as anti-tilt.
Emergency opening
Opens the door in any programme selector setting (fireman's opening). EXU-4 required.
Synchronization
Used between the operators of two single sliding doors, working together in very large openings.
17Issue 2019-06-281005274-EMen-9.0

Troubleshooting
RemediesWhat´s wrong?
The door does not open
Change the setting of the mode selector.The motor does not start
Check the mains switch and fuse in the building.
Unlock the mechanical locks.The motor starts but stops during
opening Clean the floor guide.
Check for objects jammed under the door.
The door does not close
Change the setting of the mode selector.The motor does not start
If a presence sensor is installed, check for and remove objects placed in the
presence zone.
Clean the floor guide.The motor starts but stops during
opening Check for objects jammed under the door.
The door moves slowly
Prevent traffic from using the door and allow it to close completely.
Reset the operator by setting the programme selector to AUTO and pushing
a narrow object in the small hole on the programme selector.
If the problem continues, please contact your Entrematic Group representative.
1005274-EMen-9.0Issue 2019-06-2818

Service/Maintenance
Service and adjustments performed by your Entrematic Group-authorized representative will ensure
safe and proper operation of your automatic door unit.
Remember to keep “Service Log Book”and “Site Acceptance Test and Risk Assessment”documents
available. These are used together.
The table below shows the recommended interval in months, when to replace parts during preventive
maintenance.
Abusive
Environment
Cycles/hour in operation
Part >100<100<10
High
traffic
Medium
traffic
Low
traffic
24242424Electrical emergency unit bat-
tery
12121212Mechanical emergency unit
elastic cord
661224Floor guide shoe
Standard
Felt padded
Break-out
12122436Carriage wheel
Double
Anti-derailing
24363636Sliding track
36484848Tooth belt
60606060Drive unit damper kit
60606060Lock ramp
24364860Belt clamp
48606060Plastic protector center shaft
kit
24242424Door stop rubber kit
36363636Tension wheel assembly
60606060Detachment guard
12121212Brush/sealing
Other products from Entrematic Group
•Door Systems
•Swing doors
•Automatic and manual activation units
19Issue 2019-06-281005274-EMen-9.0

We
Entrematic Group AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
declare under our sole responsibility that the type of equipment:
EM SL Single or Double, EM SL T Single or Double. With or without emergency unit
complies with the following directives:
2014/30/EU ElectroMagnetic Compatibility Directive (EMCD)
2006/42/EC Machinery Directive (MD)
2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(RoHS)
Harmonized European standards which have been applied:
EN 61000-6-2EN 60335-1
EN ISO 13849-1EN 61000-6-3
EN 16005
Other standards or technical specifications, which have been applied:
BVLBBR
EN 60335-2-103FCC 47 CFR Part 15 B
DIN 18650-1/-2
EC type examination or certificate issued by a notified or competent body (for full address, please contact Entrematic
Group AB) concerning the equipment:
TÜV B 12 07 74969 007SITAC 0137/05
The manufacturing process ensures the compliance of the equipment with the technical file. The manufacturing
process is regularly assessed by 3rd party.
The CE mark was first applied 2002-12-29.
Compilation of technical file:
Email: [email protected]Anders Forslind
Entrematic Group AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
PositionSignatureDatePlace
Global Quality ManagerKlas Hagelin2019-06-06Landskrona
Declaration of conformity
DoC 1000190-EMen-11.0
1005274-EMen-9.0Issue 2019-06-2820