Winco 8050 Reference guide

Page 1 of 8
006045 Rev EE Date 11-08-11 JWC
1. READ AND FOLLOW ALL DIRECTIONS.
2. NEVER stand on table or INJURY MAY OCCUR.
3. NEVER allow user to sleep unattended on table or INJURY MAY OCCUR.
4. NEVER leave an unconscious user unattended on table or INJURY MAY OCCUR.
5. DO NOT use table for transporting user in or with ANY type of vehicle or trailer. Winco tables have not been tested
or approved for use by an occupant in any type of vehicle or trailer.
6. NEVER leave an infant or child unattended on table or INJURY MAY OCCUR.
7. DO NOT allow children to play on or with the table or INJURY MAY OCCUR.
8. MAKE SURE Headrest Adjustment Notched Bar is fully engaged before user lays on table.
9. DO NOT put hands, feet or clothing into any openings when changing positions on table. Attendant MUST confirm
that users hands and feet are safe while changing table positions or INJURY MAY RESULT.
10. Periodically, recheck tightness of all nuts, bolts and screws.
11. USE ONLY WINCO AUTHORIZED REPLACEMENT PARTS.
12. NEVER EXCEED the recommended weight capacity of 400 lbs. (181.4 kg).
13. SAVE THESE INSTRUCTIONS for future reference and training.
8050 Adjusting Table
with Adjustable Facerest / Armrest
CUSTOMER INSTRUCTIONS
Tools needed:
Phillips-head screwdriver
Two (2) 7/16” wrenches (multiple size wrenches included)
Scissors or box cutter
Cardboard shipping container (stays under table during assembly to protect upholstery)
- If using powered tools always start hardware together by hand first -
1. After checking your product for any shipping damage, table needs to be positioned upside-down on cardboard
or protective surface. Remove all packing material and hardware that was secured for shipping. Cut tape on
corners of box so that cardboard will lay flat while you assemble table.
Arm Frame Assembly
2. Using two (2) 7/16” wrenches; assemble the two Arm Frame Standoffs to the Arm Frame Support using (2)
¼-20 x 1-¾” bolts and locknuts. See picture below.
PLEASE READ AND FAMILIARIZE YOURSELF WITH
A
LL INSTRUCTIONS BEFORE PROCEEDING WITH ASSEMBLY
PLEASE READ AND FAMILIARIZE YOURSELF WITH ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
If you have trouble understanding these instructions contact your dealer or Winco customer support, [phone]
before attempting to use this product; otherwise injury may occur.
8050 Weight Capacity = 400 lbs. (181.4 kg.)
Winco assumes no responsibility for damage or injury caused by improper assembly,
installation, use, or maintenance of these products.

Page 2 of 8
006045 Rev EE Date 11-08-11 JWC
Table Components Installation
3. Position the table upside-down on the cardboard shipping container or carpeted floor to protect upholstery.
4. Install the Face Paper Holder on the bottom of the Upholstered Face Rest using two (2) “pre-installed” 1”
black drywall screws that are located on the bottom of the Upholstered Face Rest (across from the Face
Paper Cutter.)
Holes in the Face Paper Holder will be aligned with drywall screw holes. Do not over-tighten.
5. Install the complete Arm Frame Support Assembly (you previously assembled) onto Uph. Face Rest using
the (4) “pre-installed” ¼-20 x 1” Phillips head screws; located in Face Rest.
See complete table assembly picture.
6. Use a 7/16” wrench and install the Headrest Adjustment Assembly to the bottom of the Upholstered Top,
using (2) ¼-20 x 1-3/4” hex-head bolts in the (2) sets of threaded holes in the wood of the Upholstered Top.
7. Install the Ratchet Bar (end with hole) to the inside of the LEFT Arm Frame Standoff (Left; as if laying face-
down on table),with (1) ¼-20 x 1-½” screw; (1) 1/16” nylon spacer and (1) ¼-20 locknut.
(SEE PHOTOS BELOW & NOTE)
NOTE: Nylon spacer must go between the Arm Frame Standoff and the Ratchet Bar. Tighten the ¼-20 x 1-½”
screw and locknut to snug, then loosen ¼ turn. The Ratchet Bar must be able to move for headrest adjustment.
NOTE: When adjusting the headrest, be sure to provide support with your hand, or it will drop rapidly.
Leg Installation
8. Use your 7/16” wrench to remove (8) ¼-20 x 3” Hex-head Bolts from the two (2) Table Frame Rails. You will
use these same bolts to install the legs in following steps.
9. Align the (2) Table Angled Legs with holes in Table Frame Rails. Then, insert the (previously removed) (8)
¼-20 x 3” hex head bolts and leave them slightly loose. Table Angled Leg with WINCO decal should go on
“headrest end” of table.
10. Assemble the Cross-brace to the Table Angled Legs (see next NOTE) using (4) ¼-20 x 1-½” screws and (4)
¼-20 “Nylock” lock nuts. Heads of screws should face table ends for a better appearance. Apply lock nuts
and tighten with a wrench.
NOTE: Cross-Brace is only welded on three sides at each end. Position it so that the un-welded side is
facing tabletop. (For a better appearance.)
11. Tighten all of the (8) ¼-20 x 3” hex head bolts with a wrench, that you previously left slightly loose on the
Table Angled Legs.
12. Using at least two people and turn table upright.
13. If table is not level, loosen or tighten Glide Feet (leveling feet) until table is level.
Ratchet Bar
Ratchet Bar

Page 3 of 8
006045 Rev EE Date 11-08-11 JWC
Optional Shelf Installation
14. If your table has a shelf, double-sided tape has been installed on the cross brace of the Welded Leg
Assemblies.
15. Before removing the paper on the tape, make sure you “test fit” the shelf.
16. Once you are certain where you want to position the shelf, peel off the paper to expose adhesive.
17. Carefully position shelf in place on adhesive.
Wrinkles in Vinyl – Storage and shipping can cause wrinkles of the vinyl on your Winco table. This is normal.
Please allow 1-2 weeks at room temperature (approx. 70 degrees) to allow for vinyl to expand back to original
appearance.
Do not over tighten nuts and bolts. Periodically check all fasteners for tightness.
After peeling paper from adhesive tape:
Use damp sponge to moisten tape to allow shelf to be adjusted during install.
Once ta
p
e is dr
y
shelf will sta
y
in
p
lace.

Page 4 of 8
006045 Rev EE Date 11-08-11 JWC
Parts Guide & List
Items factory installed on table: Qty. Sizing chart – part number
Face Slot Tube 1 219140
Face Paper Cutter 1 219160
Table Frame Rails 2 222600
Shelf (optional) 1 267115
4” Hinge 2 301800
1” x 2” rectangular insert caps, (gray) 4 701010
Upholstered Top 1 Call for special part number
Upholstered Face Rest 1 Call for special part number
1” drywall screws (in bottom of Face Rest) 2
face paper holder to Face Rest 566540
¼-20 x 1” Screw 4
(see bottom of Face Rest) 566517
arm-frame assembly to Face Rest
¼-20 x 3” Hex-head Bolt 8
front & rear leg assys. to table frame rail 566408
Ratchet Bar
Headrest Adjustment
Assembly - #222650

Page 5 of 8
006045 Rev EE Date 11-08-11 JWC
Parts List (continued)
Items included with table (NOT factory installed):
Table Legs
Standard Height (22”) Legs 2 221210
Special height Legs 2 Call For Part Numbers
Glide Feet (leveling feet) 4 500350
Rectangular insert caps (black, on legs) 4 701008
Glide Foot Insert 4 221235
Cross-brace 1 221300
8050 Headrest Adjustment Assembly 1 222650
Spacer, nylon (1/16 thick) 1 566312
Gray insert cap 1 700700
Arm Frame Assembly
805-860-870 Arm Frame 1 222605
Gray insert caps 2 700700
KD Standoff assy. welded 2 222630
Upholstered Armrest 2 Call for special part number
Plastic Arm Pad Panel 2 261815
Face Paper Holder 1 219100
¼-2- x 1½” Carriage Bolt 4
(4) welded brace assy. to front & rear leg assy.
566401
¼-20 x 1-½” Screw 1
(1) 805 Ratchet Bar to arm-frame standoff 566506
¼-20 x 1-¾” Hex-head Bolt 4
face-rest lock tube to table 566404
& (2) arm support to standoffs
¼-20 Nylon lock nut 7
(4) welded-brace assy. to front & rear leg assy. 566204
& (2) arm support to standoffs
& (1) arm support to 805 Ratchet Bar

Page 6 of 8
006045 Rev EE Date 11-08-11 JWC
Other Quality Winco Medical Furnishings You May Be Interested In:
Visit us online at www.wincomfg.com

Page 7 of 8
006045 Rev EE Date 11-08-11 JWC

Page 8 of 8
006045 Rev EE Date 11-08-11 JWC