Ergotron Peanut User manual

1 of 2
300-5611-00 rev. B • 06/16
Built with Anthro-DNA™
The Peanut
Product Part#
The Peanut PT1GMPW3
The Peanut for Tablets PT2GMPW3
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide
NOTE: The Peanut, Tall, is shown. The tablet and keyboard are not included.

2 of 4
300-5611-00 rev. B • 06/16
10
09
01
02
03
04
05
06
07
08
TOOLS
The Peanut comes with these tools:
• 3-way wrench
Not provided, but suggested:
• 7/16" nut driver
• 3/8" nut driver
PARTS LIST
Before beginning assembly of The Peanut, please review
the parts list to verify that your shipment is complete.
Product Quantity Part Number
01 Shelf 1
for The Peanut 225-4834-00
for The Peanut for Tablets 225-4837-00
02 Handle (installed on shelf) 1 125-5411-00
03 Column Assembly 1
for The Peanut 500-1108-00
for The Peanut for Tablets 500-1109-00
04 Cable Sleeve 1 280-5056-00
05 Base 1 225-4833-00
06 Casters, Non-locking 2 150-5117-00
07 Casters, Locking 2 150-5118-00
08 1/4-20 Nylock Nut 24 325-5259-00
09 VESA Tilt Assembly 1 835-5639-00
for Peanut for Tablets
10 Easel Assembly 1 835-5640-00
for Peanut for Tablets
11 #10-24 x 0.75" Flat Head Screw 2 325-5270-00
for Peanut for Tablets (not shown)
For Peanut for Tablets:

3 of 2
300-5611-00 rev. B • 06/16
Locking Casters
1/4-20 Nylock Nuts
325-5259-00
1/4-20 Nylock Nuts
325-5259-00
1/4-20 Nylock Nuts
325-5259-00
#10-24 x 0.75” Flat-hd Screw
325-5270-00
STEP 1 - ATTACH THE CASTERS TO THE BASE
Lay the base upside down on work surface or oor.
Align the mounting holes in each caster plate with the bolts sticking
out of the base. Locking casters (with tabs as shown) attach to the
longer base legs.
Attach each caster with four nylock nuts using a 7/16" nut driver.
STEP 2 - ATTACH BASE TO THE COLUMN
Align mounting holes in base with bolts
sticking out of the bottom of the
column.
Attach the base with four nylock nuts
using a 7/16" nut driver.
STEP 3 - ATTACH SHELF TO COLUMN AND CABLE SLEEVE
Stand the column up on its casters.
Align mounting holes on column with
bolts in shelf so the handle is over the
locking casters.
Attach the shelf with four nylock nuts
using a 7/16" nut driver.
Slip the Cable Sleeve over the tube and
press into place.
STEP 4 - ATTACH VESA MOUNT TO COLUMN
Rotate VESA plate on mounting assembly so it can lay at.
Align mounting holes in mounting assembly with holes in top of
column.
Attach VESA mounting assembly with two hex bolts using 1/8" hex key.

4 of 4
300-5611-00 rev. B • 06/16
3/8” Acorn Nut
325-5023-00
© 2016 Ergotron, Inc. All rights reserved.
All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.
Anthro-DNA is a trademark of Ergotron Inc.
STEP 5A - ATTACH DEVICE HOLDER TO VESA PLATE
Align device holder with the VESA plate so the four threaded studs on
the holder line up with four holes on the plate.
Attach the device holder to the plate with four acorn nuts using your
3/8" driver.
To adjust the device holder, loosen the adjustment knobs at the back of
the device holder, slide the top of the holder into position, then tighten
the knobs.
STEP 5B - ATTACH TABLET CASE TO VESA PLATE
Align the holes in the back of your tablet case with the four outer holes
in the VESA mount.
Attach monitor with mounting screws that come with the case.
CONGRATULATIONS! YOUR CART ASSEMBLY IS COMPLETE!
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty