Ergotron STYLEVIEW SV42-3262-1 User manual

1
5
6
2
3
4
1
5
2
3
4
5˚
60˚
12˚
180˚
180˚
20”
(508 mm)
7"
(178 mm)
EN
STYLEVIEW®
QUICK REFERENCE
777-24-037-G-00 rev.A • 07/12
ERGONOMICS
Working customize - to your size
1 Set top of monitor screen about one inch below eye level - Release brake
and lift or lower riser as needed.
2 Tilt screen for comfortable viewing and to reduce eye and neck strain.
3 Pull keyboard tray forward and position mouse tray and mouse pouch on
right or left, as needed.
4 Work with elbows bent at about 90° to minimize muscle strain.
5 If the riser moves up and down with diculty, or if it drifts out of set
position, consult the product
manual for adjustment
information.
6 Stay in charge!
Powered carts should be
plugged into outlet as often as
possible to keep battery charged
and computer running.
Moving stow - before you go
1 During normal movement, release brake and lower worksurface to
lowest position for optimal stability and unobstructed view.
2 Tuck away open trays and return mouse, scanner and other
accessories to their places.
3 Unlock both front casters.
4 Push cart from rear with elbows bent at about 90° to maximize
control and minimize muscle strain.
5 Don’t run out!
Before moving, make
sure cord is unplugged
from outlet and hooked
to basket for safe travel.
Remember, charge
battery fully 100%
every day!
Release Brake to move riser.
RANGE OF MOTION
KEYBOARD LIGHT
Your computer must be on for this light to function.
Keyboard Light will automatically turn o after 15
minutes if not manually turned o.

11
2
1
2
1
2
EN
STYLEVIEW®
QUICK REFERENCE
777-24-037-G-00 rev.A • 07/12
If other lights are ashing red/green it could indicate a power system fault. If this occurs contact Ergotron Customer Care.
NOTE: Frequent operation of the cart while battery charge levels are below 10% may reduce the life of your battery.
This power system interface will alert you to the percentage of charge remaining in the cart battery with a series of steady or ashing red, yellow or
green lights, and an alarm that will beep when charge gets below 10%. Remember, the battery needs to be charged to 100% every day, and you can
use the cart while charging, so plug-in cord as often as possible to avoid running out of power!
NOTE: Put monitor in power save mode to optimize battery run time.
When lit, alarm is enabled and will
beep when battery charge gets
below 10%. For details on enabling
and disabling alarm contact Ergotron
Customer Care.
When lit, the power system is on. When
dark, power system is o.
Battery has 100% charge.
Light ashes when charging (power cord plugged into wall
outlet) Allow battery to continue charging until light stops
ashing. After light stops ashing, it is OK to unplug the
power cord from the wall. You can use cart while charging.
Battery has less than 90% charge.
Battery has less than 60% charge.
Battery has less than 10% charge and alarm beeps. Light is
orange and then turns red when battery has less than 5%
charge. Plug-in power cord and charge to 100%! You can use
cart while charging.
Alarm Mute button. Pressing this will temporarily mute alarm.
When battery has less than 5% charge, the alarm mute is only
eective for 1 min.
Power button for internal power system outlets. Pressing this
will provide or remove power to/from components plugged
into the internal outlets.
If the battery is stored too long without recharging, the
electronics in the battery may cause the battery voltage
to drop too low. If this happens, the power system will
enter a low charge recovery mode when plugged into
power source.
During the low charge recovery process this light
will blink green.
This light will be green.
This light will be blinking red.
Once the process has nished the power system will
resume charging as normal. if the low charge recovery
process takes longer than 45 min please contact
Ergotron Customer Care.
Unlock Drawer (3 methods):
• Enter Master PIN, then press desired drawer number*.
• Enter User PIN, then press desired drawer number*.
• Key - turn clockwise 1/4 turn
*Drawer Numbers:
Lock Drawer:
• Wait 4 seconds for lock to engage automatically.
NOTE: Drawer must be fully closed to lock.
CAUTION: Close worksurface before opening drawers. Open only one drawer at a time. Do Not
push cart when drawers or worksurface are open. Failure to follow these instructions may cause
the cart to be unstable.