ESAB MXH 315 PP User manual

MXH 315 PP
MXH 420w PP
Instruction Manual
DOKP4M4060 2021 02 02 3.0

DOKP4M4060 3.0 -2- © ESAB/TBi 2021

DOKP4M4060 3.0 -3- © ESAB/TBi 2021
Contents
1Important basic information .............................................................................................................4
1.1 Safety instructions..................................................................................................................................4
1.2 Symbols and signal words......................................................................................................................5
1.3 Conditions of intended use.....................................................................................................................5
1.3.1 Application, Transport and Storage ...................................................................................................5
1.3.2 Scope of delivery ...............................................................................................................................5
1.3.3 Disposal and recycling.......................................................................................................................5
1.4 Warranty.................................................................................................................................................6
2Product description, Technical data.................................................................................................6
2.1 General area of application and functions..............................................................................................6
2.1.1 Area of application .............................................................................................................................6
2.1.2 Function .............................................................................................................................................6
2.2 Specifications .........................................................................................................................................7
2.3 Selection of a suitable torch...................................................................................................................8
2.4 Torch design...........................................................................................................................................9
3Preparing the product for use........................................................................................................10
3.1 Transport and storage..........................................................................................................................10
3.2 Installation ............................................................................................................................................10
3.3 Preparation...........................................................................................................................................10
3.3.1 Equipping the torch..........................................................................................................................10
3.3.2 Installing and changing the drive roll ...............................................................................................11
3.3.3 Installing and changing pressure roll for AlSi wire...........................................................................12
3.3.4 Changing the torch neck..................................................................................................................13
3.3.5 Installing or changing the wire guide in the torch neck....................................................................14
3.3.6 Installing or changing the wire guide in the cable assembly............................................................16
3.4 Electrical connection ............................................................................................................................17
3.4.1 Connectivity......................................................................................................................................17
3.4.2 Connection plan for ESAB MXH PP ................................................................................................18
3.5 Connection to the power source ..........................................................................................................18
3.6 Connection to the cooling circuit (water-cooled torch only) .................................................................18
3.7 Cover Locking System .........................................................................................................................19
4Product operation..........................................................................................................................19
4.1 Normal operation: Start-up...................................................................................................................19
4.2What to do in case of faults or maintenance........................................................................................20
4.3 Wire run-in............................................................................................................................................20
4.4 Adjusting the pressing force.................................................................................................................21
5Maintenance and repairs...............................................................................................................22
5.1 Regular checks.....................................................................................................................................22
5.2 Repairs on the MXH PP.......................................................................................................................23
5.3 Changing the inlet nozzle.....................................................................................................................23
6Spare parts....................................................................................................................................24
7Troubleshooting.............................................................................................................................26
8Order Numbers MXH 315 PP / 420w PP.......................................................................................28

DOKP4M4060 3.0 -4- © ESAB/TBi 2021
1 Important basic information
1.1 Safety instructions
Danger!
In order to prevent serious personal injuries and/or damage to your installation
and equipment the information and statements given in these operating instructions must
be observed. All personnel operating machines fitted with the product or doing work on
the product itself must have read these operating instructions thoroughly before starting
and must always follow the given instructions.
1. Please keep this operating manual for future reference and pass it on with the product.
2. A welding system comprises a variety of potential hazards for humans and environment.
The product must only be used by trained personnel, this also applies to setup and maintenance.
Therefore, all safety regulations in this manual, as well as in those of the connected appliances like
power source must be followed.
3. The accident prevention regulations as well as in-house and national safety-related provisions must
be strictly observed.
4. When the power source is switched on, do not touch any live parts of the torch.
5. Always keep the torch away from your body and any bystanders! Danger of the wire end exiting the
torch nozzle! If necessary, wear an eye protection during maintenance work on the torch.
6. Parts of the torch, especially in the front part, can reach very high temperatures during operation.
Please hold the torch only in the area of the handle and let it cool down before starting maintenance
work. Do not place the hot torch on or near heat-sensitive objects.
7. All leads and wires must be protected from damage. The condition of the device must be examined
periodically by trained personnel. Any damage must be professionally repaired before further use of
the system.
8. Make sure the trigger will not be activated accidentally when the torch is put down. The use of an
adequate torch holder is highly recommended.
9. Welding fumes are harmful to your health. Do only work in well ventilated areas or use a fume
extraction unit with enough capacity. Be especially careful with painted surfaces and residues of
detergents. It may be necessary to prepare these surfaces adequately to avoid the formation of
highly toxic gases.
10. Never weld near flammable or explosive materials. Risk of fire!
11. When working in closed, humid or narrow spaces, special safety measures must be observed. The
safety officer for the concerned working place must be consulted for this purpose.
12. During the welding process, there are dangers for the eyes, the skin and the hearing. Therefore,
complete welding safety equipment must be worn. This specifically includes gloves, welding jackets
as well as a face- and eye protection. Welding produces very intense light, as well as UV radiation,
which will harm the unprotected eye and skin. Take care that bystanders are also protected, e.g. by
using welding curtains.
13. Prior to doing installation and maintenance work on the product, the power supply to the complete
system must be disconnected. Make sure that the whole system is switched off and will remain so
for the time of the work. There is a risk of a life-threatening electrical shock, as well as burn and stab
injuries caused by the wire.
14. For water-cooled torch systems, please take care that no cooling water will enter the interior of the
torch. Caution is required when changing the torch neck or during transport/storage. If caution is not
taken, there is a risk of fatal electric shock and damaging the torch. Water-cooled torches should
always be equipped with a torch neck or a suitable transportation lock.
15. Modifications of the torch are not permitted and will cause the invalidation of the declaration of CE-
conformity.

DOKP4M4060 3.0 -5- © ESAB/TBi 2021
1.2 Symbols and signal words
Symbol
Signal word
Meaning
Danger!
Description of a hazard with a high degree of risk, which can lead to
death or serious injuries if it is not avoided.
Warning!
Description of a hazard with a medium degree of risk, which can
lead to death or serious injuries if it is not avoided.
Caution!
Description of a hazard with a low degree of risk, which can lead to
minor or moderate injuries if it is not avoided
Note!
Important note!
Indication of a note that contributes to intended use, or to
information on the product.
1.3 Conditions of intended use
1.3.1 Application, Transport and Storage
1. The device should only be used within the above-mentioned technical specifications and for its intended
purpose. It must only be used with Original ESAB torch necks, accessories, spare parts and wear parts.
▪Do not hammer with the torch, do not use it as a bending tool
▪Do not pull on the cable assembly
▪Do not kink cable assembly or control cable
▪Do not roll up the cable assembly to a radius smaller than 0.25 m
▪Please follow the instructions for regular cleaning in Section 5
2. The product is intended for industrial and commercial use and must only be utilized by trained
personnel. The manufacturer is not liable for any damage or accidents resulting from improper usage.
3. All installation instructions, operating instructions and maintenance instructions listed in this manual
must be observed.
4. The product must be kept dry and protected from humidity and corrosive agents when transported,
stored or used.
The welding torch is made for use within an ambient temperature between –10° and 40°C / 14° to 104°F.
Outside this range, special measures may be necessary. In freezing conditions, please use an adequate cooling
liquid.
1.3.2 Scope of delivery
▪Operating instructions
▪ESAB MXH Push-Pull welding torch
1.3.3 Disposal and recycling
▪Please do not dispose of the ESAB MXH Push-Pull welding torch in the household
waste.
▪Please dispose of the ESAB MXH Push-Pull welding torch according to country-
specific regulations.

DOKP4M4060 3.0 -6- © ESAB/TBi 2021
1.4 Warranty
Before delivery, our products are carefully checked. We guarantee, that each product is free from defects of
material and workmanship at the time of delivery and is functioning according to its intended use.
ESAB provides warranty on defects of material and workmanship according to legal requirements. Wearing
parts are exempt from this warranty.
The warranty does not cover any damages or functional deficiencies resulting from
▪overloading, abusing or non-intended use of the product
▪accidents
▪noncompliance with indications stated in these operating instructions
▪improper installation or assembly
▪insufficient maintenance
▪modifying the product from its original state
▪chemical influences
▪normal wear and tear during proper operation
ESAB assumes no liability other than for replacement or repair of faulty parts.
2 Product description, Technical data
2.1 General area of application and functions
2.1.1 Area of application
ESAB MXH PP-TX welding torches were developed as an easy way to upgrade ESAB MIG/MAG welding power
sources into a high-performance Push-Pull system.
Considerably longer cable assemblies can be used with the Push-Pull torch. Wires that are difficult to handle
e.g. AlMg wires can be easily fed over distances of up to 10.5 m through the additional wire feed system in the
torch handle. The welding process remains stable due to the even wire feed speed.
The powerful wire feed with large feed roll provides optimal performance whilst protecting the wire.
ESAB MXH PP-TX welding torches are equipped with easily changeable torch necks. Thus, the torch can be
optimally adjusted to changing tasks. Even in the event of a faulty neck, work can continue immediately with a
spare neck.
The neck can also rotate in the holder. This also makes many tasks easier.
The handle was manufactured using 2-component technology and provides an appealing, ergonomic shape
with optimized non-slip properties. The drive mechanism is easily accessible thanks to the large cover. The
contact force of the feed roll can be adjusted over a wide range.
2.1.2 Function
The wire feeding system integrated into the handle of the ESAB MXH PP-TX torch supports the main feed unit
of the power source for the wire feed. Therefore, the friction of the wire in the cable assemble no longer has a
direct impact on the wire speed, the wire is fed at a consistent speed.
In the drive unit, the wire is pressed into the groove of the driven feed roll by a smooth pressure roll. A high
feeding force can thereby be transferred without deformation of the wire.

DOKP4M4060 3.0 -7- © ESAB/TBi 2021
2.2 Specifications
ESAB MXH PP
Field of application
ESAB MIG/MAG welding torches are intended for use on CE-compliant welding
power sources for metal inert gas welding (MIG), metal active gas welding (MAG)
and metal inert gas soldering processes with commercially-available round wires.
The torches may not be used for other processes.
Type of guidance
by hand
Voltage rating
The torch is rated for a welding voltage of max. 113 V (peak value).
The control circuit (switch or micro switch) is rated for a voltage
of 50 V, max. 1 A.
Remote control devices with electronic elements may be subject to individual
specifications.
Cooling method
Gas-cooled and water-cooled versions are available. The water-cooled version
includes the additional connections for water inlet and return.
Capacity
The maximum welding current depends on the torch version used, please refer to
the type plate on the machine side connector of the torch for applicable data.
The following maximum values apply:
▪MXH 315 PP (gas-cooled): Mix: 270A; CO2: 310 A,
60% duty cycle (10 min.)
▪MXH 420w PP (water-cooled): Mix: 400A; CO2: 430A,
100% duty cycle (10 min.)
Wire diameter
0.8 - 1.6 mm
Gas flow
10 - 20 l/min
Potentiometer (2x)
standard value 10 kΩ
Operating principle for drive
Wire feed with driven roll and a parallel pressure roll
Electrical connection for motor
Max. supply voltage 42 V DC, rated power 17.5 W
Wire feed speed
approx. 2.5 - 18 m/min (depending on electrical connection of the Push-Pull torch)
Cable assembly lengths
6, 8 & 12 m
Limits of the torch cooling circuit
(for water cooled models only)
▪Min. flow: 1,2 l/min / 1,1 quarts/min
▪Min. water pressure: 2,5 bar / 36,3 PSI
▪Max. water pressure: 3,5 bar / 50,8 PSI
▪Input temperature: max. 40° C / 104° F
▪Return temperature: max. 60° C / 140° F
▪Cooling capacity: min. 1600 W, depending on the application
Important note!
Return temperatures of more than 60 °C / 140° F may cause
damage or destroy the cable assembly. The cooler must always be
filled with enough cooling liquid, please consult the user manual of
the cooling unit. In case of a high thermal load on the torch, please
use a cooler with enough capacity.
Ambient conditions
Storage -25° to +55°C (-13° to 131° F)
Operation -10° to +40°C (14° to 104° F)
Relative air humidity
to 90% at +20°C (68° F)
Technical specification
The ESAB MXH Push-Pull welding torch comply with the harmonized standard
IEC/EN 60974-7 and bear the CE mark.

DOKP4M4060 3.0 -8- © ESAB/TBi 2021
Important note!
▪The torch capacity values given refer to a standard application case using standard
accessories.
▪The torch and cable assembly capacity drop when using pulsed arc power sources.
▪In special cases e.g. in the event of very high reflective heat, the torch may overheat even
under less load than the maximum rated capacity. In this case, the welding duration in the
duty cycle must be reduced, a more powerful torch selected, or the welding conditions
must be improved.
▪ESAB products are manufactured to the current state of the art and are safe to operate if
they are used as intended.
▪The ratings are valid for cable lengths 8 and 12 m.
▪For special cable lengths > 12m, a reduction in performance is required due to the
increased heat influence.
▪For water-cooled special cable lengths > 12m a sufficient dimensioned cooling device is
needed (cooling capacity > 2KW). The coolant flow rate should not fall below 1.2 L / min.
2.3 Selection of a suitable torch
The torch model must be chosen according to the welding application. The required duty-cycle and capacity, the
cooling method and the wire diameter must be considered. If there are increased requirements, for example
caused by preheated work pieces, high heat reflection in corners etc., these must be considered by choosing a
welding torch with adequate reserve in power rating (see section 2.2).

DOKP4M4060 3.0 -9- © ESAB/TBi 2021
2.4 Torch design
Item
Description
Function/ Description
1
MXH torch neck holder
Quick-change system
1a
MXH PP Torch neck
In different versions (air and/or water-cooled models)
2
Torch switch
power source On/Off
3
Handle
4
Cover
5
Cable assembly
6
Control cable
To connect drive motor (supply voltage) and control elements
7
EURO central connector
8
Water inlet
Marked blue (water-cooled version only)
9
Water return
Marked red (water-cooled version only)
11 & 12
Potentiometer
To connect to the remote-control interface of the power supply
13
Viewing window
Control viewing window for the correct positioning of the wire guide
14
Tension spring holder
Locking device for pressure roll holder
14a
Adjusting screw
Regulating the contact pressure (pressure roll holder)
15
Knurled nut
Fixing the drive roll
100
Feed roll
For feeding the welding wire
17
Drive shaft
Drive/mounting of drive roll
19
Pressure roll
For the wire guide to the drive roller
20
Pressure roll holder
Holder of the counter-pressure roll
101
Wire guide
guides the welding wire to the feed roll
102
Inlet guide
for fixing the wire guide in the torch neck

DOKP4M4060 3.0 -10- © ESAB/TBi 2021
.
3 Preparing the product for use
3.1 Transport and storage
The following points must be observed during transport and storage:
▪To prevent danger due to the ESAB MXH PP torch falling, only place it down on substrata that have a
high load-bearing capacity and are stable.
▪The ambient temperature specifications must be observed.
(see section 2.2)
▪Protect the ESAB MXH PP torch from moisture and environmental influences.
Important note!
If the ESAB MXH PP is transported and/or stored, the torch neck (1a) must always be
installed for a water-cooled system. Otherwise there is a danger that the cooling water
could get inside the torch body.
3.2 Installation
The following points must be observed during installation:
▪Carefully remove the packaging; to prevent danger due to the torch falling, only place it down on
substrata that have a high load-bearing capacity and are stable.
▪Ensure that all ESAB MXH PP torch components are present.
(see section 2.4)
▪Please observe all sections described below for additional servicing.
3.3 Preparation
Danger!
The supply voltage to the welding machine must be disconnected before starting installation
work. It must be ensured that the entire facility remains switched of for the duration of the
work. There is a risk of fatal electric shock.
You must observe the ‘Safety instructions’ at the beginning of this document.
3.3.1 Equipping the torch
The ESAB MXH PP welding torch can be used for various welding tasks and filler materials. The accessories
integrated into the MXH PP must be individually adapted to each task for the torch to function properly and to
ensure optimum welding results. The necessary work steps are described below.
1a

DOKP4M4060 3.0 -11- © ESAB/TBi 2021
3.3.2 Installing and changing the drive roll
The wire feed will only function properly if the right drive roll is used. The drive roll must be selected according to
the wire material used and the wire diameter in accordance with Table 1. Please refer to our current list of spare
parts, if necessary. (see section 6)
Table 1: Drive rolls for ESAB MXH PP
Welding wire
Wire diameter [mm]
Pressure roll
part no.
Feed roll
part no.
Marking on
the feeder roll
0,8
0,9
1,0
1,2
1.4
1,6
All wire types
except AlSi
0459 990 081
0459 990 051
08 X
x
0459 990 052
09 X
x
0459 990 053
10 X
x
0459 990 054
12 X
x
0459 990 055
14 X
x
0459 990 056
16 X
x
AlSi *
0459 990 082
0459 990 057
1.0 -AlSi
x
0459 990 058
1.2 -AlSi
x
0459 990 059
1.6 -AlSi
x
*) The feed rolls for AlSi wires must be installed together with the special pressure roll for AlSi (part no. 0459990082)
(see section 3.3.3)
Drive roll in bold = standard version
Note:
To ensure that the torch functions correctly, only
original drive rolls specified for the ESAB MXH PP should be used!
Perform the following steps to change the drive roll.
1. Open cover (4), loosen tension spring holder (14) from locking device and flip up to open.
2. Open pressure roll holder (20) and fold to the side.
3. Loosen and unscrew knurled nut (15). If necessary, carefully remove the existing drive roll (100) from
the drive shaft (do not use any tools!)
4. Push the new drive roll (100) on to the shaft (17); in doing so the marking with the required wire
diameter must be facing upward.
5. Then put the knurled nut (15) back on and tighten by hand.

DOKP4M4060 3.0 -12- © ESAB/TBi 2021
3.3.3 Installing and changing pressure roll for AlSi wire
The optional pressure roll for AlSi wires must be installed together with the AlSi feed rolls!
Perform the following steps to change the pressure roll:
1. Open cover (4), loosen tension spring
holder (14) from locking device and flip up
to open.
2. Open pressure roll holder (20) and fold to
the side
3. Install pressure roll for AlSi (part no.
0459 990 082) according to the supplied
installation instructions:
2mm
Hex
Wrench
or Torx
T10
Clean the
pressure roll
holder
Part no. 0459 990 082
Chamfer on Top
Groove at the bottom
Only tighten
very lightly
2mm Hex Wrench
or Torx T10
Tighten plastic
nut strongly
Block screw
position

DOKP4M4060 3.0 -13- © ESAB/TBi 2021
3.3.4 Changing the torch neck
The MXH cable assembly may only by equipped with a suitable MXH PP torch neck. Different removable torch
necks, which are very easy to fit, are available for optimal adjustment to different tasks.
Important note!
Water-cooled cable assemblies must always be equipped with a water-cooled neck; gas-
cooled cable assemblies must always be equipped with a gas-cooled neck!
1. Switch off the cooling device for water-cooled torches. If another neck is not installed immediately,
empty the cooling circuit by blowing through with compressed air. The torch should be laid horizontally
for this task.
2. Cleanly cut off any welding wire still in the torch neck in front of the contact tip.
3. Loosen locking nut and pull the torch neck out of the MXH body.
Attention: Cooling liquid can leak from the neck and cable assembly of water-cooled torches. This must
not get into the handle and torch body.
4. Check the O-rings on the flange of the new torch neck to be installed for damage or loss, replace if
necessary.
5. Put on the torch neck and tighten the locking nut by hand. Do not use any tools!
Important note!
Water-cooled cable assemblies may only be transported and stored with mounted torch
neck in order to prevent the water from leaking out of the cooling circuit and getting into the
inside of the handle. The torch could be damaged from intruding liquids.

DOKP4M4060 3.0 -14- © ESAB/TBi 2021
3.3.5 Installing or changing the wire guide in the torch neck
The wire guide must be selected to match the material and diameter of the welding wire; always use the
complete equipment kit according to the following table.
Table 2: Equipment kits for torch neck
Welding wire
Equipment kit
part no.
Wire diameter
[mm]
Material of the wire guide
(J)
Length
[mm]
Inlet guide (102)
Part no.
AIMg, AlSi,
CuSi, fill wire,
stainless steel
0700 025 313
0.8 - 1.0
PA/ Bronze liner
(110)
320
0700 025 321
0700 025 314
1.2
PA/ Bronze liner
(110)
320
0700 025 322
0700 025 315
1.6
PA/ Bronze liner
(110 A)
320
0700 025 323
Steel
0700 025 316
0.8 - 1.0
Insulated liners, blue
(111)
320
0700 025 324
0700 025 317
1.2
Insulated liners, red (111)
320
0700 025 325
0700 025 318
1.6
Insulated liners, yellow
(111 A)
320
0700 025 323
Wire guides in bold = standard version

DOKP4M4060 3.0 -15- © ESAB/TBi 2021
For installation of a PA/ Bronze liner used for Alu or stainless-steel wires, please follow the instructions included
with the liner.
Complete the following steps to install an insulated liner for steel wire:
1. Remove the torch neck from the torch, see Section 3.3.3. Remove gas nozzle, contact tip and tip
holder.
2. Loosen and unscrew inlet guide (102).
3. Pull the old wire guide backwards out of the torch neck. To do this, press the wire guide into the neck
from the front if necessary.
4. Blow out the torch neck with compressed air.
5. Reassemble tip holder, contact tip and gas nozzle.
6. Select new wire guide (J) to suit the welding wire. Monitor the front end for a free inner hole and
protruding burrs; rework if necessary.
7. Insert the new wire guide (J) into the torch neck from the back.
Note: The bare end of the liner must point forwards towards the contact tip.
8. Hold the wire guide in the torch neck whilst applying light pressure to ensure that it pushes forward
against the contact tip. Then cut the wire guide flush with the end of the torch neck.
9. Monitor the end of the wire guide for a free inner hole and protruding burrs. It must be able to be
inserted into the liner nipple later. Remove the wire guide from the neck again and rework if necessary.
10. When using the yellow steel liner (111 A), the insulation must be removed on a length of 6 mm in order
to insert the liner into the nipple (see drawing).
11. The inlet guide (102) included in the equipment set must always be used. Screw inlet guide on to the
torch neck and lightly tighten.
Note: The wire guide must be inserted into the large borehole of the inlet guide in order to minimize the
loss of gas.
12. Check the O-rings on the flange of the torch neck for damage or loss; replace if necessary.
13. Put on the torch neck and tighten the locking nut by hand. Do not use any tools!
Cut flush
with neck
fasten
loosen
fasten
fasten

DOKP4M4060 3.0 -16- © ESAB/TBi 2021
3.3.6 Installing or changing the wire guide in the cable assembly
A universal PA wire guide (see Table 3) is recommended for all wire types.
Table 3
Welding wire
PA wire guide
Length
Part no.
All wire types
(0.8 –1.6 mm)
8 m
0700 025 319
12 m
0700 025 320
1. Straighten out cable assembly
2. Any welding wire remaining in the torch must be removed.
3. Loosen the locking nut (D) at the central adaptor; if necessary, strip the liner nipple (B) and O-ring (C)
from the old wire guide (R) and pull out whilst turning slightly.
4. Blow dry and oil-free compressed air through the cable assembly before installing the new wire guide
(position on central adaptor wire nipple).
5. Lightly sharpen the front end of the plastic liner, then insert as far as it will go whilst turning slightly.
Note:
Ensure that the wire guide is as far forward as it can go.
To do this, open the cover (4), lift up tension spring holder (14), push pressure roll holder
(20) to the side and use the viewing window (13) to check whether the wire guide has
been fed through to the viewing window (see Figure above). If necessary, push it further
forward by simultaneously pushing and turning the wire guide.
6. Slip the liner nipple (B) and O-ring (C) over the wire guide (R) and fasten the locking nut (D) using the
spanner.
7. Shorten the wire guide behind the central adaptor to the required length. Follow the operating
instructions of your power source.

DOKP4M4060 3.0 -17- © ESAB/TBi 2021
3.4 Electrical connection
Danger!
The supply voltage to the welding machine must be disconnected before starting installation
work. It must be ensured that the entire facility remains switched of for the duration of the work.
There is a risk of fatal electric shock.
You must observe the ‘Safety instructions’ at the beginning of this document.
3.4.1 Connectivity
3.4.1.1 Connection via Push-Pull interface of the power source
To connect the MXH PP torch to the power source, it is possible to use the push-pull interface of the power
source. This is available as a connection kit on many models.
For commissioning and wiring of this interface, please observe the instructions of the welding machine. The
assignment of the burner control line can be found in the following diagram.
Important note!
The following conditions must be met to connect the ESAB MXH PP welding torch to the
Push-Pull interface: Pmax 17W / 100%
Pmax 25W / 60%
Please note the operating instructions of the welding machine. If in doubt, please contact
your welding machine retailer.
3.4.1.2 Connection via Syntronic 3
The Syntronic 3 (ESAB Part No. 0700 025 311) can be used as an alternative to the Push-Pull interface of the
power source. The Syntronic 3 is an independent motor control unit that allows the characteristics curve
between the main drive unit and Push-Pull drive to be calibrated accurately. The main feed unit is not influenced
by the Syntronic, so that even complex regulated systems are not impaired and operate at full capacity even
with the Push-Pull torch.
The wire feed speed can be regulated between 2 m/min and max. 15 m/min.
Please follow the separate instructions for connecting the Syntronic 3.

DOKP4M4060 3.0 -18- © ESAB/TBi 2021
3.4.2 Connection plan for ESAB MXH PP
3.5 Connection to the power source
▪Connect the central connector of the torch to the power source socket.
▪Ensure that the wire guide behind the central connector is cut to the correct length. Please also
observe the instructions of your power source. When processing aluminum wire, the wire guide must
reach the feed rolls of the power source.
▪Tighten the locking nut of the central connector by hand.
▪Connect the control cable plug to the corresponding socket (suitable connection kit).
3.6 Connection to the cooling circuit (water-cooled torch only)
▪Connect the blue-marked connection hose of the torch to the inlet flow (“water-in”, cold water) of the
welding machine (cooling device).
▪Connect the red-marked connection hose of the torch to the return flow (“water-out”, warm water) of
the welding machine (cooling device).

DOKP4M4060 3.0 -19- © ESAB/TBi 2021
Important note!
Water inlet and return must not be mixed up, otherwise there is a danger of overheating and
damaging the torch.
Specifications of the torch cooling circuit (for liquid cooled torches only):
• minimum flow 1.2 l/min
• min. water pressure: 2.5 bar
• max. water pressure: 3.5 bar
• input temperature: max. 40 °C
•return temperature: max. 60 °C
• cooling capacity: min. 1600 W, up to 2000 W depending on the application
3.7 Cover Locking System
4 Product operation
Follow all instructions from section 3 before the product can be put into operation
4.1 Normal operation: Start-up
Danger!
Before starting up the system, the entire installation must be inspected in accordance with all
instructions and the applicable safety regulations.
The safety instructions at the beginning of this operating manual must be observed!
Please check the following to make sure that the system has been installed correctly:
1. Are all parts bolted tightly? (see section 3.3)
2. Has the torch neck been fastened as described and correctly and fully equipped?
(see section 3.3.4, 3.3.5)
3. Is the Euro central connector or direct connector fastened tightly? (see section 3.5, 3.6)
4. Has the wire guide been selected and installed according to specifications?
(see section 3.3.5, 3.3.6)
5. The wire run-in can now be started. (see section 4.3)
6. Has the spring tension for the pressure roll been set correctly? (see section 4.4)
7. Is the adjustment of motor characteristics required and has it been performed accordingly?
8. The ESAB MXH PP welding torch is now ready for operation.
Take the necessary safety precautions before starting the welding process!

DOKP4M4060 3.0 -20- © ESAB/TBi 2021
4.2 What to do in case of faults or maintenance
Danger!
Please observe the safety instructions at the beginning of this manual!
Damaged torches or cable assemblies must not be used anymore!
Known defects must be repaired prior to the next use of the equipment
Danger of burn injuries!
Gas nozzle and torch head get very hot during welding. Let the torch cool down prior to
doing maintenance work!!
For safety reasons the following sequence is to be strictly followed:
1. Before performing maintenance on the system, the main power of the installation must be turned off.
2. Let the torch cool down prior to doing maintenance work (e.g. replacing wear parts)!
3. Eliminate fault (see section 7) or perform maintenance (see section 5)
4. Turn on the main power of the installation.
5. If necessary, perform the wire run-in. (see section 4.3)
6. The ESAB MXH PP welding torch is now ready for operation.
4.3 Wire run-in
Wire end
deburred