ESAB SDF-250 User manual

SDF-250 STATIONARY SUBMERGED ARC WELDING POWDER
DRYING OVEN
0700 100 000 THREE PHASE 400V AC 50/60Hz
0700 100 001 ONE PHASE 110V AC 50/60Hz
INSTRUCTION MANUAL FOR SUBMERGED ARC WELDING POWDER DRYING OVEN
USAGE PURPOSE
This product is designed to dry and hold the
submerged arc welding powders at a certain
temperature. Welding powders can be dried for
the period recommended by the manufacturer,
depending on the conditions. It should only be
used in the intended use direction to avoid
possible damage to property and injuries.
BEFORE USING
Make sure that the technical specification on
the product corresponds to the electrical supply
in your network. Check the voltage and
frequency information. Check that there are no
fault that will affect the operation of the
product.
USAGE ENVIRONMENT
Flammable and explosive materials should not
be around the device. The device it should not
be covered. It should be run in a dry place.
Never use it in the rain and wet ground.
USING
Connect the appliance plug to the power supply by attaching a socket. Turn the switch to position (1) on
the top of the main panel. To set the temperature above the Digital Controller; Press and hold the SET
key for 2 seconds. Select the temperature with the Up and Down keys and press the SET key again. The
device will automatically switch off the heating when it reaches the desired temperature. The three
pilot lamps (side-by-side) on the panel show three electrical phases. If one or two does not, there is a
problem with your electricity line. 3 light should blink at the same moment. The lamps turn on during
heating. If the oven has reached the desired temperature, the lamps will turn off. Charge of the welding
powders into the top cover, do not put any other material, package, etc. from the welding powder into
the chamber. Leave a little high to hard to close the door. The lock will be fully seated. When you want
to use the welding powders, pull the lower arm than powder will discharge into a bucket. When the
bucket is full push back the arm. If you are not using the oven, turn the switch to position (0) and unplug
it. Some surfaces may be hot to the touch, use heat resistant fireproof gloves. Do not touch live parts
with electrical shock hazard.
SDF-250 Technical Information
Capacity
250 Kg (551 lb) Flux
Voltage
3 ph 400V, 3ph 230V 50/60Hz
Power
7.500 W
Temperature
0-400 °C (32-752 °F) Digital Thermostate
Storage Size L-W-H
2 pcs 45x51x60 cm, 17,71x20,07x23,62 in
Outer Dimensions
162x82x145 cm, 63.77x32,28x57,08 in
Weight
230 kg (507 lb)
ESAB Group (UK) Ltd, 322 High Holborn, 6th Floor, London,WC1V 7PB,United Kingdom www.esab.com

SCHEMATIC DIAGRAM OF SDF-250
SPARE PARTS LIST
ITEM NO
QTY
ORDERING NO
DESCRIPTION
NOTES
1
1
0700 100 002
Digital Thermostate
DT-109A
2
3
0700 100 003
Signal Lamp
220V
2
3
0700 100 004
Signal Lamp
110V
3
1
0700 100 006
Door Handle
4
1
0700 100 007
Puller Arm
5
2
0700 100 008
Castors without Brake
Back
5
2
0700 100 009
Castors with Brake
Front
6
1
0700 100 031
Cable Gland
7
2
0700 100 011
Heating Element
220V
7
2
0700 100 012
Heating Element
110V
8
1
0700 100 013
Power cable with plug
CEE 5x32A 400V plug
8
1
0700 100 014
Power cable with plug
110V
9
1
0700 100 015
Fuse (automatic)
10A
9
1
0700 100 016
Fuse (automatic)
2A
10
2
0700 100 017
Contactor 220V UNI
220V
10
2
0700 100 023
Contactor 110V UNI
110V
11
1
0700 100 018
Power Switch
12
1
0700 100 019
Terminal
set
13
1
0700 100 020
Air Valve
14
1
0700 100 164
Fiberglass Wick
SDF-250
15
1
0700 100 165
Thermocouples

CONTROL PANEL