ETEKCITY ESF24 User manual

1
Smart Fitness Scale
Model: ESF24 Series
User Manual
Questions or Concerns?
Mon – Fri, 9:00 am – 5:00 pm PST/PDT
[e-mail] • [phone]

2
Table of Contents
Package Contents
Specications
Safety Information
Function Diagram
Display Diagram
Before First Use
VeSync App Setup
Using the Smart Scale
Maintenance
Common Display Codes
Troubleshooting
Warranty Information
Customer Support
4
4
6
8
9
10
11
14
17
19
20
23
25

3
Table des matières
Contenu de l’emballage
Caractéristiques techniques
Consignes de sécurité
Schéma des fonctions
Schéma de l’écran
Avant la première utilisation
Conguration de l’application VeSync
Utilisation de la balance intelligente
Maintenance
Codes d’achage communs
Dépannage
Informations relatives à la garantie
Service client
4
4
26
28
29
30
31
34
37
39
40
43
45

4
1 ×Smart Fitness Scale
3 ×1.5V AAA Batteries (Pre-Installed)
1 ×Quick Start Guide
Specications
Package Contents
Weight Capacity 180 kg / 28 st / 400 lb
Increments 0.05 kg / 0.2 lb
Weight Units kg / st / lb
Platform Tempered Glass
Battery 3 x 1.5V AAA batteries
Auto-Off 30 seconds
Dimensions 30 x 30 x 2.5 cm / 11.8 x 11.8 x 1 in
Operating System iOS®12.0+ or Android™ 6.0+

5
1 × Balance de tness intelligente
3 × Piles AAA de 1.5V (préinstallées)
1 ×Guide de démarrage rapide
Caractéristiques techniques
Contenu de l’emballage
Capacité de poids 180kg / 28st / 400lb
Incréments 0.05kg / 0.2lb
Unités de poids kg / st / lb
Plate-forme Verre trempé
Piles 3 piles AAA de 1.5V
Arrêt automatique 30 secondes
Dimensions 30 x 30 x 2.5cm / 11.8 x 11.8 x 1po
Système d’exploitation iOS®12.0+ ou Android™ 6.0+

6
Safety Information
• This scale should not be used to diagnose or treat any medical
condition.
• Scale data should not be used as a substitute for medical advice
from a healthcare professional.
• This scale uses a harmless electrical current to measure body fat.
Consult a healthcare professional before using the smart scale if
you use medical electronic equipment such as a pacemaker.
• Check the scale before using. Do not use the scale if it is damaged
in any way.
• Do not strike or hit the scale. Do not use the scale if the glass is
cracked or broken. Due to the nature of tempered glass, the glass
will shatter if there is even a slight crack. If you see a crack, contact
Customer Support immediately (page 25).
Please read and follow all instructions and safety guidelines
in this manual.
READ AND SAVE THESE INSTRUCTIONS
Medical
General Use

7
• Do not mix new and old batteries.
• If the scale is not in use for a long period of time, remove
the batteries to extend the lifetime of the scale.
Batteries
• The glass platform is slippery when wet. Always make sure the
platform and your feet are dry before stepping on for measurement.
• Place the scale on a hard, at surface to avoid tipping.
• To weigh safely and accurately, stand with your feet shoulder-
width apart while on the scale. Do not stand on the edge of the
scale or jump on the scale.
• Avoid standing on the scale for a long period of time, or when
you are not weighing yourself.
• Do not overload the scale. Maximum weight capacity is 180 kg /
28 st / 400 lb.
• Keep the scale in a cool area with low humidity. Keep the
scale away from heat sources, such as ovens or heaters.
Avoid temperature uctuations. Store the scale in a horizontal
position, not vertical.
• Handle with care. Not for commercial use. Household use only.

8
Function Diagram
A. Weighing Platform
B. Display
C. Anti-Skid Padding
D. Battery Compartment
BA
D
C

9
Display Diagram
A. Weight Measurement
B. Bluetooth®Icon
C. Weight Units
A
B
C

10
Before First Use
1. Open the battery compartment on the underside of the
scale. Remove the included AAA batteries.
2. Remove the plastic insulator strip from the battery
compartment.
3. Replace the batteries. Follow the guidelines in the battery
compartment to match the +and –terminals.
Slide
1.5v - AAA
1.5v - AAA
1.5v - AAA
1.5V - AAA
1.5V - AAA
1.5V - AAA
Slide

11
VeSync App Setup
1. To download the VeSync app, scan the QR code or
search “VeSync” in the Apple App Store®or Google
Play Store.
Note: Due to app updates and improvements, the VeSync app may be
slightly different than shown in the manual. In case of any differences,
follow the in-app instructions.
Note:
• This scale uses the VeSync app, not the VeSyncFit app.
• For Android users, you may need to select “Allow” to use VeSync.

12
2. Open the VeSync app. If you already have an account,
tap Log In. To create a new account, tap Sign Up.
Note: You must create your own VeSync account to use third-party
services and products. These will not work with a guest account. With a
VeSync account, you can also allow your family and friends to use your
smart tness scale.
Note: You can change the name and icon at any time in the smart
tness scale settings.
3. Make sure to enable Bluetooth®permission of the APP
and turn on Bluetooth®. For Android users, please allow
the app to access nearby devices in your phone settings.
Note: If your Android phone system is lower than Android™ 12.0+, please
authorize the location (GPS) permission of the VESYNC app in your
phone settings.
4. Tap +in the VeSync app and select your smart
tness scale.
5. Follow the in-app instructions to connect to your
smart tness scale.

13
Creating a User
If you are a new user, you will need to enter physical
information before weighing yourself for the rst time
so the scale can calculate your body metrics. Follow
the in-app instructions to create a user.
Note:
• Entering inaccurate information will make the scale’s
measurements less accurate.
• If you don’t identify with the available gender options,
or are unsure, pick the option that you think best
physically matches you. This choice is used for physical
measurements, such as body fat percentages.

14
Using the Smart Scale
Note:
• To see measurements besides weight, you must connect the
scale to the VeSync app (see page 11).
• If you are pregnant, scale measurements will not be accurate.
1. Place the scale on a hard, at surface (not a carpet or
mat). [Figure 1.1]
Note: Placing on carpet may cause inaccurate measurements or tipping.
[Figure 1.1]

15
2. Step on the scale, then step off. Wait for the LED screen
to display “0.0” before using.
3. Place dry, bare feet on the scale’s conductive areas.
Stand on the scale until the display ashes several times,
showing your nal measurement. [Figure 1.2] If your
smart scale is connected to the VeSync app, additional
results (such as BMI, body fat, etc) will show in the app.
4. If you want to measure the weight of your baby or pet, you
can click the “ ”(Expand) button in the lower right corner
of the home page and click the “ ”(Baby Mode) button
to enter the baby measurement mode and measure
according to the prompts. In baby mode, the APP will only
measure weight and BMI.
[Figure 1.2]

16
Switching Units
1. To change the unit of measurement (kg, lb, or st), lightly
tap on the scale and open the VeSync app. Select the
scale(you should see “Connected” in the app), then tap
the Settings icon ( ). You can adjust the units on this
page. [Figure 1.3]
2. The default unit is pounds (lb). After changing units, the
scale will show the new unit of measurement.
LB KG ST
Device
Home Page
[Figure 1.3]

17
Maintenance
Clearing the Smart Scale
If the scale has been moved or ipped upside down, it
must be cleared to ensure accurate results.
1. Place the scale on a hard, at surface.
2. Step on the scale until digits appear on the display, then
step off. [Figure 2.1]
3. The scale will show “ ” when cleared. [Figure 2.2]
[Figure 2.1] [Figure 2.2]

18
Cleaning the Smart Scale
Replacing the Batteries
The display will show “ ” when the batteries need to be
replaced.
1. Open the battery compartment on the underside of
the scale.
2. Remove the old batteries and dispose of them properly.
3. Install 3 new 1.5V AAA batteries, making sure they are
placed under the correct polarity.
4. Replace the battery compartment cover.
• Use a slightly damp cloth to clean the surface of the
scale, followed by a soft, dry cloth to wipe away any
remaining moisture.
• Do not use chemical or abrasive cleaning agents to
clean the scale.
Note: The scale may need to be cleared after replacing the batteries.

19
Common Display Codes
Wireless Connection No Wireless Connection
Change Battery
OverloadClearing

20
Troubleshooting
The scale doesn’t turn on.
• Check if the batteries are properly installed. If using the scale
for the rst time, remove the plastic insulator strip from the
battery compartment.
Information ashes on the display and then disappears.
• The batteries are low and may need to be replaced.
The smart scale doesn’t connect with the VeSync app.
• Make sure your phone’s operating system is running on iOS
12.0+ or Android 6.0+.
• Close and relaunch the VeSync app. Make sure you’re using
the latest version.
• Make sure to enable Bluetooth permission of the APP and
turn on Bluetooth. For Android users, please allow the app to
access nearby devices in your phone settings.
Note: If your Android phone system is lower than Android™ 12.0+, please
authorize the location (GPS) permission of the VeSync app in your phone
settings.
• Make sure your scale and phone are within 10 m / 30 ft of
each other.
• Make sure the scale is not currently connected to any other
phone or app.
• Try turning off any VPN apps.