EUFY RoboVac T2253 User manual

RoboVac
Owner’s Manual
T2253 51005002511 V03

01
Thank you for purchasing RoboVac. Carefully read all the instructions below before
using this device, and keep this manual for future reference.
Table of Contents
02 ImportantSafetyInstructions
16 AboutYourRoboVac
What's in the Box
RoboVac Anatomy
20 UsingYourRoboVac
Important Tips Before Use
Preparation
Charge Your RoboVac
Use Your RoboVac with the EufyHome App
Start / Pause Cleaning
Select a Cleaning Mode
Select a Suction Power Level
Use Mopping System
Use the Boundary Strip
Use Your RoboVac with Amazon Alexa /
the Google Assistant
33 CleaningandMaintenance
Clean the Dust Collector and Filter
Clean the Mopping Cloth and Water Tank
Clean the Rolling Brush
Clean the Side Brush
Replace the Side Brush
Clean the Sensors and Charging Pins
Clean the Swivel Wheel
42 Troubleshooting
Voice Alert
47 Specications
48 CustomerService

02 03
Important Safety Instructions
To reduce the risk of injury or damage, keep these
instructions at hand when setting up, using, and
maintaining this device .
WARNINGSYMBOLSUSED
This is the safety alert symbol. This symbol alerts you
to potential hazards that could result in property
damage and/or serious bodily harm or death.
• This device can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of this device in a safe
way and understand the hazards involved.
• Children should be supervised to ensure they do
not play with this device.
• Cleaning and maintenance shall not be performed
by children without adult supervision.
• This device is only to be used with the power supply
unit provided.
• Before cleaning or maintaining this device, the plug
must be removed from the outlet.
• The battery in this device should only be replaced
by a skilled professional.
• When removing the battery, disconnect the device
from the supply mains.
• To recharge the battery, only use the detachable
adapter (US/CA: GSCU0600S019V12E; UK:
GSCB0600S019V12E; EU: GSCV0600S019V12E; AU:
GSCS0600S019V12E) provided with this device.
• The battery must be removed before this device is
disposed of. To remove the battery, first unscrew
the screws on the bottom, then remove the back
cover. Remove the battery by disconnecting the
quick connector.
• The used battery should be placed in a sealed
plastic bag and disposed of safely according to local
environmental regulations.
• The external flexible cable or cord of the power
supply unit cannot be replaced; if the cord is
damaged, the power supply unit shall be disposed
of.
• This device is for indoor use only.
• This device is not a toy. Do not sit or stand on
this device. Small children and pets should be
supervised when this device is operating.
• Store and operate this device in room temperature
environments only.
• Do not use this device to pick up anything that is
burning or smoking.
• Do not use this device to clean up spills of bleach,
paint, chemicals, or anything wet.
• Before using this device, pick up objects like clothing
and loose paper. Lift up cords for blinds or curtains.
Move power cords, sharp-pointed and fragile
objects out of the way. If this device passes over a
power cord and drags it, an object could be pulled
off a table or shelf.
• If the room to be cleaned has a balcony, a physical
barrier should be used to prevent access to the
balcony and to ensure safe operation.
• Do not place anything on top of this device.

04 05
• Be aware that this device moves around on its
own. Take care when walking in the area where this
device is operating to avoid stepping on it.
• Do not operate this device in areas with exposed
electrical outlets on the floor.
• Do not expose the electronics of this device, its
battery, or the integrated Charging Base. There are
no user-serviceable parts inside.
• Do not use this device on an unfinished, unsealed,
waxed or rough floor. It may result in damage to
the floor and this device. Use only on hard floor
surfaces or low-pile carpets, and not on carpets with
tasseled edges or loose threads.
• This device has been designed to be used on floors
without scratching them. We still recommend that
you test this device on a small area of the room to
be cleaned to ensure no scratches are made before
cleaning the whole room.
• Only use attachments recommended or described
in this manual.
• Do not handle the appliance or plug with wet hands.
• Ensure that the dust bag and/or filters are correctly
in-place before usage.
• Do not use a battery pack or appliance that is
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behavior
resulting in fire, explosion, or risk of injury.
• Do not expose the battery pack or appliance to
fire or excessive temperature. Exposure to fire or
temperature above 130°C may cause an explosion.
• Do not modify or attempt to repair the appliance or
the battery pack (as applicable), except as indicated
in the instructions for use and care.
• Follow all charging instructions and do not charge
the battery pack or appliance outside of the
temperature range specified in the instructions.
Charging improperly or at temperatures outside of
the specified range may damage the battery and
increase the risk of fire.
Notice
This symbol on the device or its packaging
indicates:
Do not dispose of electrical appliances as
unsorted municipal waste; use separate
collection facilities. Contact your local authority
for information regarding the collection
systems available. If electrical appliances are
disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and
get into the food chain, damaging your health
and well-being. When replacing old appliances
with new ones, the retailer is legally obliged to
take back your old appliance for disposal at
least free of charge.
FCCStatement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Warning:Changes or modications not expressly
approved by the party responsible for compliance could

06 07
void the user's authority to operate the equipment.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna. (2)
Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on
a circuit dierent from that to which the receiver is
connected. (4) Consult the dealer or an experienced
radio / TV technician for help.
ISEDComplianceStatement
This device contains license-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada's license-exempt
RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including
interference that may cause undesired operation of
the device.
RFExposureComplianceStatement
This equipment complies with FCC/IC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with minimum distance 20cm between the
radiator and your body.
DeclarationofConformity
This product complies with the radio interference
requirements of the European Community. Hereby,
Anker Innovations Limited declares that the radio
equipment type T2253 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet
address: https://www.eufylife.com/
Maximum output power: 18 dBm (For EU)
Frequency band: 2.4G band (2.4000GHz - 2.4835GHz)
GBDeclarationofConformity
Hereby, Anker Innovations Limited declares that
the product type T2253 is in compliance with Radio
Equipment Regulations 2017 and The Restriction of
the Use of Certain Hazardous Substances in Electrical
and Electronic Equipment Regulations 2012. The full
text of the GB declaration of conformity is available at
the following internet address: https://www.eufy.com.
TrademarkNotice
• Amazon, Echo, Alexa and all related logos are
trademarks of Amazon.com, Inc. or its affiliates.
• Apple and the Apple logo are trademarks of Apple
Inc., registered in the U.S. and other countries. App
Store is a service mark of Apple Inc., registered in
the U.S. and other countries.
• Google Play and the Google Play logo are
trademarks of Google Inc.
• Google Home is a trademark of Google Inc.

08 09
Consignes de sécurité importantes
Pour réduire le risque de blessure ou de dommage,
gardez ces consignes de sécurité à portée de main
lors de la configuration, l'utilisation et l'entretien de cet
appareil .
SYMBOLESD'AVERTISSEMENTUTILISÉS
Il s'agit du symbole d'avertissement de sécurité. Ce
symbole vous alerte sur les dangers potentiels qui
peuvent entraîner des dommages matériels et/ou
des lésions corporelles graves ou la mort.
• Cet appareil peut être utilisé par des enfants
âgés de 8 ans et plus, ainsi que des personnes
présentant des capacités physiques, sensorielles ou
mentales réduites, ou un manque d'expérience et
de connaissances, si celles-ci sont sous surveillance
ou ont reçu les instructions d'utilisation de cet
appareil et comprennent les risques encourus, et
l'utilisent dans un endroit sûr.
• Les enfants doivent être surveillés afin de s'assurer
qu'ils ne jouent pas avec cet appareil.
• Le nettoyage et l'entretien ne doivent pas être
effectués par des enfants sans la supervision des
adultes.
• Cet appareil doit uniquement être utilisé avec le
bloc d'alimentation fourni.
• Avant de nettoyer ou d'entretenir cet appareil, vous
devez le débrancher de sa prise d'alimentation.
• La batterie de cet appareil ne doit être remplacée
que par un professionnel qualifié.
• Lors du retrait de la batterie, débranchez l'appareil
du secteur.
• Pour recharger la batterie, n'utilisez que
l'adaptateur détachable (États-Unis/Canada :
GSCU0600S019V12E ; R-U :GSCB0600S019V12E ;
AUS : GSCS0600S019V12E ; UE :
GSCV0600S019V12E) fourni avec cet appareil.
• La batterie doit être retirée de cet appareil avant
de le mettre au rebut. Pour retirer la batterie,
desserrez les vis du fond, puis retirez le capot
arrière. Retirez la batterie en débranchant le
connecteur rapide.
• La batterie usagée doit être placée dans un sac
en plastique hermétique et éliminée en toute
sécurité, conformément aux réglementations
environnementales locales.
• Le câble flexible externe ou le cordon du bloc
d'alimentation ne peut pas être remplacé ; si le
cordon est endommagé, l'unité d'alimentation doit
être éliminée.
• Cet appareil est destiné exclusivement à une
utilisation en intérieur.
• Cet appareil n'est pas un jouet. Veillez à ne pas vous
tenir debout ou assis sur cet appareil. Les jeunes
enfants et les animaux de compagnie doivent être
surveillés lors du fonctionnement de cet appareil.
• Entreposez et utilisez cet appareil dans des
environnements à température ambiante.
• N'utilisez pas cet appareil pour ramasser tout
élément en train de brûler ou fumant.
• N'utilisez pas cet appareil pour nettoyer des
déversements d'eau de javel, de peinture, de
produits chimiques ou quoi que ce soit d'humide.
• Avant d'utiliser cet appareil, ramassez les objets tels

10 11
que les vêtements et les feuilles de papier. Relevez
les persiennes ou les rideaux proches du sol.
Enlevez du passage les cordons d'alimentation ainsi
que les objets pointus et fragiles. Si cet appareil
passe au-dessus d'un cordon d'alimentation et le
traîne avec lui, un objet peut tomber d'une table ou
d'une étagère.
• Si la pièce à nettoyer possède un balcon, une
barrière physique doit être utilisée pour empêcher
l'accès au balcon et garantir un fonctionnement
sécurisé.
• Veuillez ne rien placer sur le dessus de cet appareil.
• Gardez à l'esprit que cet appareil se déplace par ses
propres moyens. Faites attention en marchant dans
la zone où cet appareil fonctionne, afin d'éviter de
marcher dessus.
• N'utilisez pas cet appareil dans des zones avec
prises électriques exposées sur le plancher.
• N'exposez pas l'électronique de cet appareil, de
sa batterie ou de la base de chargement intégrée.
L'appareil ne contient aucune pièce réparable par
l'utilisateur.
• N'utilisez pas cet appareil sur un sol inachevé, non
vitrifié, ciré ou rugueux. Cela peut entraîner des
dommages sur le sol et cet appareil. N'utilisez cet
appareil que sur les sols durs et les tapis ras, et non
sur les tapis avec des glands ou des franges.
• Cet appareil a été conçu pour être utilisé sur des
planchers sans le rayer. Nous vous recommandons
de toujours tester l'appareil sur une petite zone
de la pièce à nettoyer, avant de nettoyer la
salle entière, pour s'assurer qu'aucune rayure
n'apparaisse.
• Utilisez uniquement les accessoires recommandés
ou décrits dans ce manuel.
• Ne manipulez pas l'appareil ou la fiche avec les
mains mouillées.
• Assurez-vous que le sac à poussière et/ou les filtres
sont en place avant utilisation.
• N'utilisez pas de batterie ou d'appareil endommagé
ou modifié. Les batteries endommagées ou
modifiées peuvent présenter un fonctionnement
imprévisible risquant d'entraîner un incendie, une
explosion ou des blessures.
• N'exposez pas la batterie ou l'appareil au feu ou à
des températures excessives. L'exposition au feu
ou à une température supérieure à 130°C peut
provoquer une explosion.
• Ne modifiez pas et n'essayez pas de réparer
l'appareil ou la batterie (si applicable), sauf si cela
est indiqué dans les instructions d'utilisation et
d'entretien.
• Suivez toutes les instructions de charge et ne
chargez pas la batterie ou l'appareil en dehors
de la plage de température indiquée dans les
instructions. Une charge incorrecte ou à des
températures hors de la plage spécifiée peut
endommager la batterie et augmenter le risque
d'incendie.

12 13
Avis
Ce symbole sur le produit ou son emballage
indique :
Ne jetez pas les appareils électriques de la
même manière que les déchets municipaux
non triés ; utilisez une infrastructure de
collecte séparée. Contactez directement
votre commune pour plus d'informations
concernant les systèmes de collecte
disponibles. Si des appareils électriques sont
jetés dans des décharges ou des dépotoirs,
des substances dangereuses peuvent s'infiltrer
dans les eaux souterraines et entrer dans la
chaîne alimentaire, nuire à votre santé et votre
bien-être. Quand vous remplacez vos anciens
appareils par de nouveaux, le détaillant est
légalement obligé de reprendre votre ancien
appareil pour son élimination, au minimum
gratuitement.
DéclarationFCC
Cet appareil est conforme à la partie 15 du règlement
de la FCC. Le fonctionnement est soumis aux deux
conditions suivantes : (1) cet appareil ne doit pas
produire d'interférences nuisibles, et (2) cet appareil doit
accepter toutes les interférences subies, même celles
susceptibles d'en compromettre le fonctionnement.
Avertissement : les changements ou les modications
non expressément approuvés par la partie responsable
de la conformité pourraient entraîner une annulation de
l'autorisation d'utilisation de l'équipement.
Remarque : cet appareil a été testé et déclaré conforme
aux restrictions relatives à un appareil numérique de
Classe B, en application de la partie 15 du règlement de
la FCC. Ces restrictions sont désignées an de fournir
une protection raisonnable contre des interférences
nuisibles dans une installation résidentielle.
Cet appareil génère, utilise et peut émettre des
fréquences radio qui peuvent causer des interférences
nuisibles aux radiocommunications si l’appareil n’est
pas installé et utilisé conformément aux instructions.
Cependant, il n'est nullement garanti que ces
interférences se produiront dans une installation
particulière.Si cet appareil provoque des interférences
nuisibles à la réception de la radio ou de la télévision, ce
qui peut être déterminé en mettant en route l'appareil
et en l'arrêtant, il est recommandé d'essayer de
corriger les interférences en prenant l'une ou plusieurs
des mesures suivantes : (1) réorienter ou déplacer
l'antenne de réception , (2) éloigner davantage l'appareil
du récepteur ; (3) brancher l'appareil à une prise sur
un circuit diérent de celui auquel le récepteur est
connecté ; (4) consulter le revendeur ou un technicien
expérimenté en radio/télévision pour obtenir une
assistance.

14 15
Déclarationd'IndustrieCanada
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Déclarationdeconformitéaveclesnormes
d'expositionauxRF
Cet équipement est conforme aux limites d'exposition
aux radiations FCC/IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et
utilisé avec une distance minimale de 20 cm entre le
radiateur et votre corps.
Déclarationdeconformité
Ce produit est conforme aux exigences en matière
d'interférences radio de la Communauté européenne.
Par les présentes, Anker Innovations Limited déclare
que l'équipement radio de type T2253 est conforme
à la directive 2014/53/UE. Le texte complet de
la déclaration de conformité à la réglementation
européenne est disponible à l'adresse Internet
suivante : https://www.eufylife.com/
Puissance de sortie maximale : 18 dBm (pour l'UE)
Bande de fréquence : Bande 2,4 G (2,4000 GHz -
2,4835 GHz)
Avisdemarquecommerciale
• Amazon, Echo, Alexa et tous les logos associés sont
des marques commerciales d'Amazon.com, Inc. ou
de ses filiales.
• Apple et le logo Apple sont des marques déposées
d'Apple Inc., enregistrées aux États-Unis et dans
d'autres pays. App Store est une marque de service
d'Apple Inc., enregistrée aux États-Unis et dans
d'autres pays.
• Google Play et le logo Google Play sont des marques
de Google Inc.
• Google Home est une marque de Google Inc.

16 17
About Your RoboVac
What'sintheBox
Charging Base
Additional Filter
Boundary Strip
6.6 ft / 2 m Length
Disposable Mopping
Cloths (x5)
Filter Elements (x4)
Power Adapter
Cleaning Tool
Adhesive Tapes (x2)
Washable Mopping Cloth
Owner’s Manual &
Other Documents
RoboVac
Additional Side Brushes (x2)
Cable Ties (x5)
Water Tank
Waterproof Pad
RoboVacAnatomy
A.Top&Side
Spot cleaning button
Recharge button
Auto cleaning control button Wi-Fi status light
Bumper
Infrared sensor
Main power
switch (On/O)
Dust collector
Dust collector release button
B.Bottom
Charging
contact pins
Swivel wheel
Hall sensors
Path tracking sensor
Battery compartment
Rolling brush
Side brush
Drop sensors
Drop sensors
Wheels
Brush guard

18 19
C.DustCollector
Filter
D.SuctionInlet
Dust collector
Suction inlet Suction inlet
E.ChargingBase
Charging contact pins Power cord storage
compartment
Power socket
Status light
F.WaterTank
Fliter element
Fliter element
Snap joints Snap joints
Water inlet
Water inlet cover
Cloth attachment area
Mopping Cloth
Slot
Movable pulley
Buttons&Indicators
Start/PauseCleaning
• Solid blue: standby, cleaning, pause cleaning,
returning to charging base or fully charged
• Solid orange: standby or working in low battery
status
• Breathing orange (when docked to charging
base): charging
• Flashing red: error
* Refer to the “Troubleshooting>VoiceAlert”
section in this manual for solutions.
ResettheWi-FiConnection (Press and hold for 10
seconds)
ReturntoChargingBase
• Flashing blue slowly: returning to charging
base
• Solid blue: standby or paused
SpotCleaning
• Flashing blue slowly: Spot Mode
• Solid blue: standby or paused

20 21
• When you use the FindMyRobot function via the EufyHome app, all
three LED indicators are solid blue and a voice prompt is heard.
• To conserve power, the blue light on the button becomes dim
when:
• RoboVac is not docked to the Charging Base and has been inactive
for 10 minutes;
• RoboVac is fully charged for 1 minute.
(Wi-FiStatusLight) Status
Slowly ashing blue Waiting for connection
Rapidly ashing blue Connecting with your wireless router
Solid blue Connected to your wireless router
Using Your RoboVac
ImportantTipsBeforeUse
AB C
DE F
Remove power cords and small objects from the floor that may entangle
RoboVac. You can use the supplied cable ties to organize your wires and
power cords.
Fold tasseled edges of area rugs underneath to prevent tangling RoboVac.
Avoid cleaning very dark-colored high-pile rugs or rugs thicker than 1.02in /
26mm as they may cause RoboVac to malfunction.
It is strongly recommended to place boundary strips in front of fireplaces
and certain areas (i.e. air vents) that may cause damage to RoboVac if
entered.
Keep RoboVac away from wet areas during cleaning.
RoboVac may climb on top of objects less than 0.63in / 16mm in height.
Remove these objects if possible.
Anti-drop sensors will prevent RoboVac from tumbling downstairs and steep
drops in most cases. Sensors are lesseffective if dirty or used on carpeted/
reflective/very dark-colored floors. It is recommended to place physical
barriers to block off areas where RoboVac may fall.
Preparation
1
Remove the sticker on the power switch, and the foam blocks beside the
bumper before use.
2
Install the side brush before use.
3
Before mopping, attach the waterproof pad to the Charging Base to keep
the oor dry. Make sure it is rmly installed. Skip this step if mopping is
not needed.

22 23
4
Turn on the main power switch at the right side of RoboVac.
ON
5
Place the Charging Base on a level surface and against a wall.
6
Allow the clearance of at least 3ft / 1m on each side and at least 6ft /
2m in front of the Charging Base. If there is not enough room, move the
Charging Base to a new place and check whether RoboVac can return to it
normally; if not, contact eufy customer service for help.
7
Connect the round connector of the adapter into the power socket on the
Charging Base and the other end into a wall outlet.
When the Charging Base connects to AC power, the LED indicator on
the Charging Base is SOLID WHITE.
• Install the Charging Base in a location that RoboVac can easily access.
It is recommended to place the Charging Base against a wall, and on a
hard-level surface rather than on rugs or carpets.
• Always keep the Charging Base plugged in, otherwise RoboVac will not
automatically return to it.
ChargeYourRoboVac
• Make sure RoboVac is fully charged before use.
• RoboVac returns to the Charging Base at the end of a cleaning cycle or when
its battery is running low.
Method1: Attach RoboVac to the Charging Base by aligning its charging pins
with the charging pins on the base.

24 25
Method2: Press to return RoboVac to the Charging Base.
• Turn off the main power switch if RoboVac will not be used for a
long period of time. To preserve the battery’s lifespan, recharge at
least once every 6 months.
UseYourRoboVacwiththeEufyHomeApp
To enjoy all available features, it is recommended to control your RoboVac via
the EufyHome app.
Beforeyoustart,makesurethat:
• Your smartphone or tablet is connected to a Wi-Fi network.
• Your smartphone or tablet is running iOS 9.0 (or above) or Android 4.4 (or
above).
• The 2.4GHz band wireless signal is enabled on your wireless router.
• The Wi-Fi status light on RoboVac is slowly flashing blue.
• RoboVac is attached to the Charging Base to ensure it has enough power
during setup.
EufyHome
EufyHome
1
Download the EufyHome app from the App Store (iOS devices) or Google
Play (Android devices).
2
Open the app and create a user account.
3
Tap the “+” icon to add RoboVac to your EufyHome account.
4
Follow the instructions in the app to set up the Wi-Fi connection.
- After connecting successfully, you can control RoboVac via the app.
- With the app, you can select a cleaning mode, set the time, schedule a
cleaning, view the system status, receive notifications and access additional
features.
Wi-FiStatusLight
Slowly flashing blue Waiting for connection
Rapidly flashing
blue
Connecting with your wireless
router
Solid blue Connected with your wireless
router
• If RoboVac gets stuck in any space, tap FindMyRobot in the app
to find the machine.
ResettheWi-Ficonnection
To reset the Wi-Fi connection, press and hold on RoboVac for 10 seconds.
At the same time, RoboVac will restore the factory default settings.
- You will hear a voice prompt when the settings have been reset and the Wi-Fi
status light will slowly flash blue. Now you can follow the Wi-Fi instructions in
the EufyHome app to set up the Wi-Fi connection.
ScheduleCleaning
With the EufyHome app, you can schedule RoboVac to start cleaning at a
particular time.
• You can set the time and customize the cleaning schedules
from Sunday to Saturday on the EufyHome app. This function is
available in the app only.

26 27
Start/PauseCleaning
• Make sure the main power switch at the side of RoboVac is turned
on before use.
• You can also start or pause cleaning via the EufyHome app.
1
Press on RoboVac to start cleaning in Auto Mode.
2
Press again to pause cleaning.
SelectaCleaningMode
• You can also select a cleaning mode via the EufyHome app.
Auto-cleaning
After startup, RoboVac moves from the Charging Base and automatically
determines its cleaning route, following a Z-shaped cleaning method. When
the entire clean is finished, RoboVac automatically returns to the Charging
Base.
Press on RoboVac to start cleaning in Auto Mode.
• In the EufyHome app, RoboVac can be set to return to the
Charging Base automatically if the battery level becomes low.
Once recharged, RoboVac will resume to finish the remaining
cleaning.
• By default, RoboVac starts in Auto cleaning mode when it is turned
on.

28 29
Spotcleaning
RoboVac intensively cleans a specific area in a spiral pattern, useful if there is a
concentrated area of dust or debris. In Spot mode, RoboVac will stop cleaning
after 2 minutes.
Press on RoboVac to start cleaning in Spot Mode.
SelectaSuctionPowerLevel
In the EufyHome app, select a suction power level according to your needs:
• Standard (Default)
• Turbo
• Max
• BoostIQ™
• When RoboVac starts cleaning the next time, it will clean according
to the suction power level you previously selected.
Select BoostIQ™ feature
In the EufyHome app, select the BoostIQ™ feature according to your needs.
While cleaning at standard suction power level, RoboVac will automatically
increase the suction power if it detects that stronger power is needed to
ensure the best clean. BoostIQ™ is ideal for cleaning thicker carpets and hard-
to-sweep messes, which will reduce the total cleaning time, but increase the
noise level. If the vacuuming noise caused by BoostIQ™ disturbs you, you can
disable this feature.
UseMoppingSystem
• The mopping mode is not recommended when no one is at home.
• Only use the mopping mode on a floor without carpets.
• Remove the water tank when RoboVac is under charging or not in
use.
1
Before mopping, install the waterproof pad under the Charging Base to
protect the oor.
2
Wet the mopping cloth and wring it until it does not drip. Insert the cloth
along the bracket slot and stick it rmly.
• Use either the washable mopping cloth or the disposable cloth for
mopping.
Water Barrier

30 31
3
Open the water inlet cover to ll the water tank, then close the cover.
• Do not use floor cleaner or detergent which may block the filter
elements.
4
Install the water tank into the bottom of RoboVac until a click is heard.
• The mopping mode is only intended for a clean floor without
stubborn stains. To achieve a better mopping effect, it is
recommended to clean the floor with RoboVac three times before
installing the mopping module.
5
Select a cleaning mode to start cleaning.
• RoboVac automatically sweeps and mops in the selected mode.
6
When RoboVac finishes working and returns to the Charging Base, press
the release button to remove the dust collector and the water tank.
7
Remove the water tank and put the dust collector back into the main unit.
• After mopping, remove the water tank, empty any remaining
water and clean the washable mopping cloth to prevent the cloth
becoming mildewed or producing a peculiar smell. The disposable
mopping cloth is for single-use only. For how to maintain the
mopping cloth and water tank, refer to the “Cleaning and
Maintenance” section in this manual.

32 33
UsetheBoundaryStrip
With the Boundary Strip, you can keep RoboVac away from any area or item
you do not want RoboVac to clean. RoboVac will recognize the Boundary Strip
and will not cross into the blocked-off area.
1
Identify the area or item you do not want RoboVac to get close to.
2
If necessary, use scissors to cut the Boundary Strip to a shorter length. Be
sure to correctly measure the length before cutting.
3
Apply the supplied strips of adhesive tape to lay the Boundary Strip at on
the oor. MakesurethestripisplacedFLATontheoororunderan
arearug.
1
2
• If the Boundary Strip is rolled up, remove and then re-apply on the
floor with adhesive tape. Otherwise the Boundary Strip may not
work well.
• Make sure the Boundary Strip is placed on the same surface plane
RoboVac is used on.
• Be careful not to damage the floor when using adhesive tape. It is
not recommended for use on carpets.
• Keep the Boundary Strip away from objects that emit excessive
heat.
UseYourRoboVacwithAmazonAlexa/
theGoogleAssistant
Amazon Alexa or the Google Assistant is a smart voice control device that
enables you to control RoboVac with your voice.
Currently this feature only supports English, German, French, and Spanish. You
could check regularly if more languages are supported at https://www.eufylife.
com/support/.
Beforeyoustart,makesurethat:
• RoboVac is attached to the Charging Base to ensure there is enough power.
• RoboVac is connected with the EufyHome app.
• You have an Amazon Alexa-enabled device (i.e. Amazon Echo, Echo Dot and
Amazon Tap, Echo Show, Echo Spot) or a device enabled with the Google
Assistant (i.e. Google Home, Google Home Mini). These devices are sold
separately.
• The Amazon Alexa app or Google Home app is already installed on your
smart device, and you have created an account.
TocontrolRoboVacwithAmazonAlexaortheGoogleAssistant
1
Open the EufyHome app and find “Smartintegrations” in the top left.
2
Follow the on-screen instructions to complete the setup.
• For more information about how RoboVac works with Amazon
Alexa / the Google Assistant, visit https://www.eufylife.com/
support/ for details.
Cleaning and Maintenance
Before cleaning and maintaining, turn off the device and unplug the adapter.
For optimal performance, follow the instructions below to clean and maintain
RoboVac regularly. The cleaning/replacement frequency will depend on your
RoboVac usage habits.
Recommendedcleaning/replacementfrequency
RoboVacPart CleaningFrequency ReplacementFrequency
Dust Collector After each use -
Filter Once every week
(Twice a week if you have a pet)
Every 6 months or after
every 50 rounds of cleaning
Side Brush Once every month Every 3-6 months (or when
visibly worn)
Rolling Brush Once every week Every 6-12 months

34 35
RoboVacPart CleaningFrequency ReplacementFrequency
Brush Guard Once every month Every 3-6 months (or when
the silicone rubber strip on
the brush guard becomes
visibly worn)
Sensors Once every month -
Charging Pins Once every month -
Swivel Wheel Once every month -
Washable
Mopping Cloth After each use -
Water Tank After each use -
Filter Elements - Every 6 months (or when
they become yellow)
CleantheDustCollectorandFilter
1
Press the dust collector release button to pull the dust collector out.
2
Open and empty the dust collector.
3
Remove the filter.
4
Tap the filter to remove dust.
5
Rinse the dust collector and filter thoroughly with water.
1min
Do not use a brush, hot water, or any detergent to clean the filter.

36 37
6
Air-dry the dust collector and filter completely before next use. You may
change to use the other filter if the original one is not completely dry.
24
h
7
Place the filter back into the dust collector.
8
Push the dust collector back into the main unit.
CleantheMoppingClothandWaterTank
A dirty mopping cloth will affect the mopping performance. Clean the washable
mopping cloth and water tank before use.
24
h
1
After each use, remove the mopping cloth from the water tank.
2
Rinse the mopping cloth and water tank thoroughly with water.
3
Air-dry the mopping cloth and water tank completely to avoid being
mildewed or producing unpleasant smell.
4
To discard your single-use mopping cloth, remove and drop it into a trash
container.