Euroflex VAPOUR M4S User manual

HYBRID FLOOR STEAMER
INSTRUCTION MANUAL
Before using this product, please read the instructions and keep it for future references.
All in One Steam Cleaner
M4S

2Safety Instruction
IMPORTANT SAF
When using an electrical appliance, basic safety
precautions should always be observed, including the
following:
Read all instructions before using this appliance.
WARNING! To reduce the risk of fire, electrical shock,
or injury:
1. This appliance is authorized for household/domestic
use only.
2. Do not charge or use outdoors or on wet surfaces. Do
not immerse the floor steamer in water or other liquids.
3. Do not allow floor steamer to be used as a toy. Close
attention is necessary when used by or near children.
Do not leave Steamer unattended. Always unplug
unit when not in use.
4. Use only as described and for the uses described
in this manual. Use only manufacturer’s approved
and supplied parts and accessories. Use of other
accessories is not recommended and will void the
warranty.
5. AlwaysmakesuretheHandleAssemblyisintheupright
position before plugging in or unplugging. Keep cord
away from heated surfaces (e.g., cooking surfaces)
and sharp edges and corners.
6. Do not use if power cord or plug has been damaged,
or if any part of appliance has been dropped,
damaged, left outdoors, or dropped in water. Do not
attempt to disassemble or repair appliance. Return it
to manufacturer or an authorized service center for
examination or repair.
7. Do not wrap cord too tightly around appliance. Never
carryby the cordor yank todisconnect from anoutlet.
To unplug, always grasp plug to remove from outlet –
do not pull on cord.
8. Do not handle the cord or the appliance with wet
hands or bare feet.

3
Safety Instruction
ETY INSTRUCTION .
9. Look closely at steamer and follow all labels and
marking instructions.
10. Do not put any objects into openings. Do not use with any
opening blocked.
11. Keep hair, loose clothing, fingers and all parts of body
away from openings and moving parts.
12. Before filling with water or emptying, always place
Handle Assembly in upright position, unplug the
appliance and allow it to briefly cool down. Always
turntheBoiler Capslowlytoopen thewatertank– this
will allow any remaining steam to escape gradually.
13. Use caution while emptying the appliance. Contact
with hot water or steam may cause burns.
14. To unlock the steam cleaner,
press the safety button on the
right side (1).
At the end of use it is
recommended to lock the
appliance pressing the button
on the left side (2).
15. Never use cleaning solutions, perfumes, oils or other
chemical substances other than tap or distilled/
demineralized water in the Steamer. Use of chemicals
may damage Steamer and will void the warranty.
16. Be sure Boiler Cap is (and remains) closed during use.
17. When in use, never turn the appliance on its side. Do
notdirectsteamatpeople,animalsorotherelectrical
equipment (i.e, inside an oven).
18. Do not operate around flammable or combustible
liquids such as gasoline or in areas where fumes may
be present.

4Safety Instruction
19. The Steamer is not intended for space heating
purposes.
20. To reduce the likelihood of circuit overload, do
not operate another high wattage appliance on
the same circuit. Plug in to a standard (220-240V,
50/60Hz) electrical outlet.
21. Do not use extension cords or outlets with inadequate
voltage. Use only heavy duty, high-rated extensions
cords.
22. Store appliance indoors in a cool, dry place.
23. If appliance is damaged, it must be repaired by
manufacturer in order to avoid safety issues to the
operator.
24. This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of appliance by a
person responsible for their safety.
25. Read and follow all important notices in this guide.
ATTENTION!Thisappliance is equipped with a 3-prong
grounded power cord. Insert only into a 3-prong
grounded electrical outlet. Do not try to remove the
contacts of the grounded connection.
IMPORTANT SAF
• Extreme care should be taken when opening the
Boiler Cap as it may become hot during use and
escaping steam can cause scalding.
CAUTIONS

5
Safety Instruction
•Do not use your Floor Steamer without a Hard Surface
Pad or Carpet Glide & Pad attached to the system.
•Never leave your Floor Steamer in one spot on any
surface for any period of time. Make sure that the Floor
Steamer Handle Assembly is in the full “UP POSITION”
when not in use - this turns the Steamer Off.
CAUTIONS
PleasereadalloftheinstructionsforuseandImportantSafety
Instructions carefully. Remove and discard all packaging
materials and keep them out of the reach of children.
*IMPORTANT*
Save your back
No need to
press hard
The steamer
does the
work for you
Attention: the photographs and/or drawings in this document are for illustrative
purposes only. Actual appliance and the accessories may vary due to product
enhancement.
Safety Informations in Digital Format: www.plastecs.it/warning
ETY INSTRUCTION .
Euroflex relieves itself of any liability for damages that shall be
the result of improper use of the appliance, not in conformity
with what’s written in this instruction manual.

Product Description
6Product Description
One (1) Floor Steamer
PARKING PAD
16
14
13
6
2
2
7
10
1
8
3
9
4
5
3
11
15
12
1 - Steam Handle with Switch
2 - Locking Buttons
3 - Cord Winders
4 - Cleaning Hose Clamp
5 - Measuring Cup (pre-marked)
6 - Boiler Cap
7 - Steam Ready Indicator Light
(green)
8 - Power Indicator Light
(orange)
9 - Power Cord
10 - Steam Nozzles
11 - Extension Tube
12 - Funnel
13 - Carpet Slider Microfiber Pad
14 - Carpet Glider
15 - Microfiber Floor Pads
16 - Parking Pad
Technical Data
Adapter Input: 220-240V~50/60Hz
Cord Length: 7 meters/23 feet
Power: 1200 watts
Boiler: Stainless Steel
Boiler Capacity: 0.6 liter/20 ounces

Product Description
7
Product Description
ACCESSORIES
1 - Detail Nozzle
2 - Nylon Small Brushes
3 - Window Cleaner
4 - Small Brush Adapter
5 - Small Brush
6 - Fitted Microfiber Pad for Small Brush
7 - Scraper
8 - Grout Brush
9 - Accessory Bag
8
13
7
2
9
456

Before Use
8Before Use
1FLOOR STEAMER MODE
Assembly of Parts & Preparation of Steamer
Make sure all parts are in the box (see pg 6-7).
IMPORTANT! FOLLOW THESE INSTRUCTIONS CAREFULLY.
WARNING! Always ensure steam switch is off and not
steaming when attaching an accessory to the unit.
A. Attach Handle to Steamer
• Insert the lower Extension Tube into the Floor Steamer
Base and press firmly in place (as shown in Fig. A).
• Insert the upper Extension Tube into the lower extension
tube and press firmly in place (as shown in Fig. B).
• Insert the Handle Extension Tube into the upper extension
tube and press firmly in place (as shown in Fig. C).
Attention! The lower Extension Tube has the cord support pointing down.
The upper Extension Tube has the cord support pointing upwards.

Before Use
9
Before Use
B. Attach Cleaning Pads to Steamer
WARNING! To prevent floor damage, ALWAYS attach either the
Microfiber Floor Pad or the Carpet Glide Accessory with Carpet
Pad when using your Floor Steamer. NEVER USE WITHOUT EITHER
OF THESE ATTACHMENTS AFFIXED TO THE MACHINE.
ATTACHING SCRUBBING FLOOR PAD
Scrubbing Floor Pad – Place Microfiber Floor Pad
face down on the floor, wide side forward, with
center Scrub Strip facing down (and positioned to
match metal heat plate on bottom of Base-see “A”).
Hold Floor Steamer about 2” above Pad and gently
place Floor Steamer on the Pad. Firmly press down
to ensure Pad is adhered to the Floor Steamer.
ATTACHING CARPET GLIDE WITH CARPET PAD
Place Carpet Glide face up on floor. Center and
place Carpet Pad on top of Carpet Glide. Hold
Floor Steamer over Carpet Glide and gently lower
the Steamer onto the Glide. Make sure the 4 clips
on Glide are around the outside of the Steamer
Base and using hands, attach the 4 clips of the
Carpet Glide to the Steamer Base.
USE ON HARDWOOD FLOORS – For hardwood floors,
use only on “sealed” hardwood surfaces.
Move Steamer forward and backward while
cleaning, carefully observing the amount of steam
used, as too much water could cause damage.
Steam can cause wax to be stripped from, and consequently damage, some
varieties of linoleum flooring. ALWAYS test a small, inconspicuous portion of the
floor BEFORE using steam to ensure that your linoleum floor does not have this
issue. For some varieties of linoleum or vinyl floors the floor steamer is harder to
push forward and back.
NOTE: See “Maintenance & Cleaning” for care and cleaning instructions for
Microfiber Pads.
*IMPORTANT NOTE ABOUT LINOLEUM FLOORING*
A - Heat Plate on
bottom of Base
boosts the cleaning
performance.

Before Use
10 Before Use
Use ordinary tap water. Distilled or demineralized water is recommended
if tap water is too hard. DO NOT add detergents, perfumes, oils, or other
chemical substances to the Boiler. The product warranty will be null and
void if anything other than water is added to the Boiler.
*IMPORTANT*
C. Filling Boiler with Water
WARNINGS:
• Carefully read all instructions before removing Boiler Cap.
• Always unplug appliance before filling the Boiler.
Follow these instructions to avoid overfilling the Boiler:
• Be sure appliance is unplugged from the
electrical power outlet, and has cooled for
at least 5 minutes before filling with water.
• Make sure Handle Assembly is in the
upright “off” position. Remove Boiler Cap
by turning it counterclockwise.
• Pour in 600 mls of water using
the Measuring Cup and Filler
Funnel provided – fill cup to the
“200 ml” marking three times.
Be careful not to overfill the
Boiler. Please note that excess
water will be flushed out during
use if the Boiler is overfilled,
resulting in wet floors.
• Replace Boiler Cap by turning it clockwise. Do not tighten
Boiler Cap too much – finger tightening is sufficient to lock the
steam in the Boiler. If using cold water, heating time is about
3-5 minutes. If using warm water, heating time is reduced.
• Do not overfill the Boiler as excess water will be flushed out
of the Boiler before dry steam will emit.
• If re-filling the Boiler while Steamer has been in use, be sure
to allow Steamer to cool for at least 5 minutes and loosen
Boiler Cap slowly to allow any excess steam to escape
before completely removing Cap. (See page 12, “Refilling
Boiler During Use” for detailed instructions.)
*IMPORTANT*
100 ml
200 ml
A
N
T
(
M
a
x
100 ml
200 ml
A
N
T
I
B
A
K
(
M
a
x
)

Using Your Floor Steamer
11
Using Your Floor Steamer
2Using Your Floor Steamer
A. Using the Parking Pad
You can use the Parking Pad if the Steamer is warm or hot.
B. Starting the Appliance
• Be sure Boiler is filled with water and
Boiler Cap is securely in place.
• Insert the plug into a-3 prong grounded
electrical outlet (orange Power
Indicator Light will illuminate).
• Keeping the handle in the upright “Off”
position, wait until the (green) Steam
Ready Indicator Light illuminates.
Once Boiler is filled and the green Steam Ready Indicator Light
glows, Steamer is ready to clean the floors.
The Parking Pad is provided to prevent floor
damage that can result from leaving a hot steamer
resting on the same spot for too long. ALWAYS
place Floor Steamer on the Parking Pad when not
in use, or while it is cooling before storage.
CAUTIONS
PARKING PAD
C. Using Steam
• Press the button on the right
side of the handle to unlock the
appliance.
•Toemitsteamfromtheunderside
of the Steamer, press the FRONT
button on the handle.
You will find that your Floor Steamer can easily
clean most hard surfaces and floors using the
steam from the underside alone.
PLEASE NOTE: The green Steam Ready Indicator Light may turn on and off
during use. This is normal and not a fault.
NOTE: Some recondensed water may be emitted when the handle is first pulled
down after filling. This is normal.
FRONT
RIGHT
BUTTON

Using Your Floor Steamer
12 Using Your Floor Steamer
The Steam Nozzles are meant to be used in steam “bursts” and should never be used
on a sustained basis. The Steam Nozzles will loosen especially difficult debris and will
assist in cleaning hard to reach areas such as floor edges.
*IMPORTANT*
D. Using Steam (continued)
• To emit steam from the front
nozzles and the maximum
steam from the underside of
the steamer, press the REAR
button on the handle.
• IMPORTANT: at the end of
the cleaning task, press the
button on the left side to
lock the appliance in safety
mode.
The Floor Steamer has a Boiler that should not be overfilled. To avoid the
potential for overfilling, only refill the Boiler when it is completely run out of
water and only add 600ml. Always follow the practice of using the Floor
Steamer until it has run out of water and then refill 600ml only.
If floor cleaning is completed and water remains in the Boiler, the Floor
Steamer can be stored with the remaining water in the Boiler, there will be
no harm done to the unit. At the next cleaning session simply heat up the
unit and use the water already in the Boiler, then refill when empty.
Or alternatively at the next cleaning session, open the Boiler Cap when the
unitisstillcoldandpouroutthewaterandthenrefill(ifthisalternativemethod
is used, it is recommended that only 500ml of water is added, because the
unit will not completely drain when the water is poured out from the Boiler).
*IMPORTANT*
NOTE: Your Steamer will not need refilling for about 20-25 minutes
of usage.
The Floor Steamer will stop producing steam when the Boiler is
empty. When this happens unplug and store unit or refill with water
per instructions (below).
NOTE: If the Floor or Carpet Pad becomes too wet or too dirty,
replace with a clean, dry Pad and continue cleaning.
E. Refilling Boiler During Use
When the Floor Steamer has run out of water, there will be no more
steam coming out of the unit. At this stage it is time to refill the Boiler.
Follow the refilling instructions below.

Using Your Floor Steamer
13
Using Your Floor Steamer
WARNING: Let Steamer cool 5 minutes before opening Boiler Cap. Use
care when opening Boiler Cap as it may still be hot and steam may
escape, causing burns. If Boiler is still hot, water may spurt out during
refilling which can also cause burns.
• Always use ordinary tap water.
• If tap water is too hard, use distilled or demineralized water to avoid
the risk of mineral deposits and sediment from forming.
• Do not add detergents, perfumes, oils or other chemical substances to
the Boiler. This will damage the Steamer and void the warranty.
• The green Steam Ready Indicator Light may turn on and off during use.
This is normal and not a fault.
REMINDERS
Do not overfill the Boiler as excess water will be flushed out of the Boiler
before dry steam will emit.
*IMPORTANT*
• Unplug the appliance from the electrical power outlet. This will stop
the Steamer from continuing to heat up.
• Slowly turn the Boiler Cap counterclockwise, ensuring that no
steam is present.
• Be sure Steamer has cooled 5 minutes before refilling with water.
The product warranty will be null and void if
anything other than water is added to the
Boiler.
• Pour in 600 mls of water using the Measuring
Cup and Filler Funnel provided – fill the
Measuring Cup to the 200 ml marking 3
times. Be careful not to overfill the Boiler.
• Replace Boiler Cap by turning it clockwise.
Do not tighten Boiler Cap too much – finger
tightening is sufficient to lock the steam in
the Boiler.
• Insert plug into 3-prong electrical outlet. Wait for green Steam
Ready Indicator Light to turn on. Steamer is ready to use once
again.
100 ml
200 ml
A
N
T
(
M
a

Cleaner Accessories
14 Cleaner Accessories
3PORTABLE STEAM CLEANER MODE
Multipurpose Portable Steam Cleaner
The Hybrid Floor Steamer is a 2 in 1 model
thatconvertsintoamultipurposeportable
steam cleaner with just one click. The
portable steam cleaner features include:
1. Lightweight and portable unit.
2. Ergonomicsteam handlefor easyof use.
3. Versatile and quick change accessories.
4. On/off control.
5. Security locking button.
6. Cleans many areas such as bathrooms,
kitchens, pet areas and more.
Accessories - Attachment & Descriptions
A. Always use the Parking Pad
B. Attach Handle to Steamer
To use: Hold down the locking button on the
Steam handle while sliding it in an Extension
Tube. Besure thelocking buttonlines upwith
the hole on the Extension Tube and button
locks in place.
To attach Extension Tubes together: Press
down the locking button while sliding Tubes
together. Be sure button and hole line up
and button locks in place.
To disconnect Extension Tubes: Press the
locking button and pull the two sections
apart.

Cleaner Accessories
15
Cleaner Accessories
C. Attach Extension Tube to Brush Adapter
Once the desired Brush is attached
to the Brush Adapter, press the
locking buttonon theExtension Tube
while sliding the Tube in the Brush
Adapter. Ensure the locking button
and the hole on the Brush Adapter
line up.
D. Attach Extension Tube or Steam Handle to Detail Nozzle
The Detail Nozzle provides a powerful
steamjetveryusefulforcleaninghard
to reach areas. It is ideal for blasting
dirt out of tight areas, cleaning door
and window tracks, shutters and
sanitary fixtures.
To use: Slide andlock DetailNozzle on
the Steam Handle or Extension Tube.
E. Attach Grout Brush to Detail Nozzle
The Grout Brush is designed to clean
thegrout inbetween tiles.Use onfloors
grouted,backsplashesandinshowers.
To use: Push the Grout Brush on the
end of the Detail Nozzle.
(Detail Nozzleshould beconnected to
the Steam Handle or Extension Tubes.)
F. Attach Extension Tube or Steam Handle to Window Cleaner
The Window Cleaner is very useful for
cleaning large windows and glass.
To use: Connect Window Cleaner to
Steam Handle or Extension Tube(s) for
hard to reach surfaces. Apply steam
liberally, rub with soft spongy edge,
then remove excess water and dirt
with Window Cleaner Blade. Wipe dirt
from Window Cleaner blade.
CAUTION: When cleaning windows, always avoid any sudden changes
in temperature to prevent glass breakage or cracks.

Cleaner Accessories
16 Cleaner Accessories
G. Attach Nylon Detail Brush to Detail Nozzle
The Nylon Brush is used to help scrub
particularly tough dirt.
To use: Push the Nylon Brush on the
end of the Detail Nozzle. (Detail
Nozzle should be connected to the
Steam Handle or Extension Tubes.
H . Attach Scraper to Detail Nozzle
The Scraper is best for removing
small amounts of wallpaper and
also anything that can be scraped
from a flat surface, e.g., grease
deposits in an oven. It is also useful
when defrosting freezers.
To use: Push the Scraper on the end of the Detail Nozzle. (Detail
Nozzle should be connected to the Steam Handle or Extension
Tubes.)
I. Connecting Brush Adapter to Small Brush
The Small Brush attaches either to
the extension tube(s) or the steam
handle and is used to clean smaller
areas that the Floor Steamer cannot
easily reach, such as corners of
floors, stairs and around furniture
legs.
To use: Attach Small Brush to Small Brush Adapter. Attach Extension
Tube or steam handle to Adapter by pressing the locking button
while sliding Tube or handle into Brush Adapter. Be sure button and
hole line up (see images “B” and “C” above) and button locks in
place.
*CLICK
*CLICK
180°

Cleaner Accessories
17
Cleaner Accessories
J. Attaching Microfiber Pad to Small Brush
A fitted Microfiber Pad should be placed over the bristles of the
Small Brush to clean smooth surfaces such as kitchen cupboards,
splash backs, countertops, etc. Fit the Small Microfiber Pad over
the Small Brush as shown below.
Steam Release
To release steam from the Steam
Handle, press the button on FRONT.
Steam will continue to be released
while the button is pressed.
To stop the steam, stop pressing the
button.
To move the steam cleaner
around simply grab the
base at the top of the arch
as shown in the image.
4
IMPORTANT: When the Steam Cleaner has run out of water, steam,
output will cease. Follow refill instructions (page 12) to use
your Steam Cleaner again.
FRONT
While using the appliance
as a portable steam
cleaner, keep the arch
perpendicular (upright) to
the body of the appliance to
avoid the ejection of steam
from the front nozzles.
WARNING

Using Your Floor Steamer
18 Using Your Floor Steamer - Maintenance & Cleaning
5Turning Steam Cleaner Off
• To turn Steam Cleaner off, press the Power Switch and
unplug the electrical cord from the power outlet.
• Any remaining water can be left in the unit.
• We recommend distilled or demineralised water as the best
way to care for and utilize your Steam Cleaner.
• If tap water is too hard, use distilled or demineralized water to
avoid the risk of staining pale colored fabrics.
• Do not add detergents, perfumes, oils or other chemical
substances.
REMINDERS
NEVER HOLD THE STEAM CLEANER UNDER THE TAP TO FILL.
Use the filling cup provided to fill the Boiler.
If distilled or demineralised water is regularly used in the Steam
Cleaner, cleaning of the Boiler can be done less frequently.
In some areas tap water is very hard, it is recommended that
the Boiler is cleaned more frequently if hard water is used.
6Cleaning Steam Cleaner
We recommend you periodically clean the Steam Cleaner to
prevent the accumulation of calcium, mineral deposits and other
sediment caused by the use of tap water. After every 10-15 refills,
fill the Boiler three-quarters full of hot tap water, shake several
times and empty out the water into a sink.
Repeat several times to ensure that the Boiler is flushed of any
calcium or mineral deposits. Wipe the Steam Cleaner with a
damp cloth and dry.
Maintenance & Cleaning

Maintenance & Cleaning
19
Maintenance & Cleaning
If the Steam Cleaner and Boiler is not cleaned according to
the instructions above and the product fails and/or the steam
pathways are blocked, the appliance owner should send the
product for servicing by contacting the Customer Support Line.
The cleaning of the Boiler and Steamer is the sole responsibility
of the appliance owner. Calcium, mineral deposits and other
sediments left to build up in the Steam Cleaner causing it to
fail and/or the steam pathways in the Steam Cleaner to block,
is not covered by the product warranty. Users must follow the
cleaning instructions above.
The Steam Cleaner is intended for domestic household use
only. It is not intended for commercial use. Any use other
than for domestic household purposes will void the product
warranty.
Replacement of Brushes, Microfiber Pads
and Accessories
The Nylon Brushes and the fitted Microfiber Pad for the Small
Brush provided with the Steam Cleaner are to get you started
using your Steam Cleaner. As these brushes and microfiber
pads become dirty or wear out, replacement brushes and
microfiber pads can be purchased from the retailer from
which you purchased your Steam Cleaner and/or from most
other electrical appliance retail outlets.
Itisnormaltohavereplacementsofthebrushesandmicrofiber
pads close at hand when doing cleaning as the brushes wear
out or the microfiber pads become dirty.
Any of the other accessory tools are replaceable by
contacting the Customer Support Line.
7

Tips & Reminders
20 Tips & Reminders
Steam Cleaner Tips & Reminders
Steam cleaning allows the user to clean chemical-free by using
the powerof steam,in place ofharsh chemical-basedcleaners.
The heat from the steam softens and loosens dirt on surfaces,
while the steam pressure lifts the dirt away. All that is left to do
is to wipe the surface to remove the dirt and moisture using a
cloth (preferably with a microfiber cloth).
TIP: to get the best cleaning results use a microfiber cloth to
wipe the dirt and moisture from the surface being cleaned.
Microfiber is designed to pick up and hold dirt, a great aid
in lifting and removing the dirt that the steam cleaner has
softened and loosened. Also, Microfiber requires moisture to
glide over surfaces, the steam cleaner provides moisture that
the Microfiber needs to glide. Microfiber and Steam, a great
cleaning combination!
Making Contact with Surfaces
The steam is at its hottest just as it leaves the nozzle/accessory.
This is the area of the steam output that should be used to
clean to achieve maximum performance. All accessories
should make direct contact with the surfaces being cleaned
to transfer the heat from the Steam Cleaner to the surface in
order to soften and loosen dirt. If the accessory being used
does not make contact with the surface, the desired results
may not be achieved. If assistance is required contact our
Customer Support Line.
TIP: steam will clean hard, sealed, non-porous surfaces in
place of harsh chemical-based cleaners and detergents.
For soft furnishings such as carpets, rugs, lounges, children’s
toys etc, steam will refresh and deodorise the fibres. Steam is
not used to clean carpets, other than to spot clean. To clean
carpets proper carpet cleaning equipment should be used.
8