Euroflex Vapour M6S User manual

INSTRUCTION MANUAL
Before using this product, please read the instructions and keep it for future references.
Compact Multi Purpose
Steam Cleaner
M6S

2Safety Instructions
IMPORTANT SAFE TY INSTRUCTIONS
.
IMPORTANT: SAVE THESE INSTRUCTIONS
SAFETY WARNING
• This appliance should not be used by children
and persons with reduced physical, sensory
or mental capabilities. Close attention is
necessary when used by or near children,
pets or plants. Do not leave this appliance
unattended. Always disconnect the
appliance from the power supply when not
in use. Keep out of reach of children.
• Children should not play with the appliance.
• Cleaning and user maintenance should not
be done by children without supervision.
• Keep the appliance out of reach of children
when it is plugged in or cooling down.
• If the electrical cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualied person in order to
avoid a hazard.
• The steam released from the appliance is
extremely hot. Both appliance and accessory
tools may scald. Avoid direct contact. The
steam symbol (symbol 5597 relative to IEC
60417-1) warns operators that there is the risk
of scalding!
• Never open the boiler cap while using the
device.
• Unscrew the boiler cap only when the device
is switched off, pressure-free and cooled.
9

3
Safety Instructions
IMPORTANT SAFE TY INSTRUCTIONS
.
• This appliance is not to be used if it has been
dropped, if there are visible signs of damage
or if it is leaking.
• Disconnect the appliance from the power
supply prior to any maintenance or cleaning
operations. Always allow the appliance to
completely cool down.
• Do not leave the appliance unattended
while it is connected to the power supply.
Disconnect the plug if you need to get away
even just for a few minutes.
Important Notices
• ThisappliancecomplieswithEuropeanDirectivesregarding“electromagnetic
compatibility” and “Electrical product safety”. The appliance carries CE
marking.
• Do not direct the steam jet towards people, animals or plants.
• Do not point the jet of steam in the direction of electrical or household
appliances.
• Do not use the appliance with wet hands or bare feet.
• Donotusetheappliancewhenclosetoammableorexplosivesubstances.
• Do not insert any object in the various openings and do not use the
appliance if any opening is obstructed.
• Do not store the appliance outdoors.
• Donot exposethe appliance toatmosphericagents,water,humidity or
heat sources.
• Use a dry or slightly damp cloth to clean this appliance.
• Only use accessories and spare parts recommended by the manufacturer.
• The manufacturer, importer or distributor assume no responsibility for
damage to property or injury to persons, in the event that this appliance is
damaged as result of improper use or assembly.
• Repairsmustbe carriedoutexclusivelybypersonnelauthorizedbythe
manufacturer. Equipment repaired by unauthorised personnel poses a
danger to the user and cancels the warranty.
• Do not pull on the electrical cable. Do not use the cable to move the
appliance. Do not crush the cable when closing doors. Avoid any contact
with sharp edges and corners. Keep the cable away from hot surfaces.

4Safety Instructions
ATTENTION! This appliance is equipped with a 3-prong
grounded power cord. Insert only into a 3-prong grounded
electrical outlet. Do not try to remove the contacts of the
grounded connection.
• Always drain condensed water from hose before use or if unit
has been left idle for a period of time.To drain hose, direct
steam gun opening into a sink or other appropriate container
and slide the steam control trigger forward on the Steam Gun.
Once hose is emptied, normal use may be resumed.
• Extreme care should be taken when opening the Boiler Cap
as it may become hot during use and escaping steam can
cause scalding.
CAUTIONS
• The manufacturer reserves the right to make changes to the design and
features of the appliance without notice.
• This appliance is intended for domestic use only.
• Connect the appliance only after making sure that the voltage of the
electrical network corresponds to that indicated on the plate of the
appliance.
• Do not immerse the appliance in water or other liquids.Always turn off
andunplugappliancewhenllingwithwater.
• Do not allow to be used as a toy. Close attention is necessary when used
by or near children, pets or plants.
• Do not use with any opening blocked.
• Follow all labels and marking instructions on the appliance.
• Before lling with water or emptying, always switch off the appliance,
unplug it and allow it to cool completely.Always turn the boiler cap slowly
to open the boiler.This will allow any residual steam to escape gradually.
• Use caution while emptying the appliance. Contact with hot metal parts,
hot water or steam may cause burns.
• Be sure Boiler Cap is (and remains) closed during use.
• Never use cleaning solutions, perfumes, oils or other chemical substances
otherthantapordistilled/demineralizedwaterintheappliance. Use of
chemicals may damage appliance and will void your warranty.
• When in use, never turn the appliance on its side.
IMPORTANT SAFE TY INSTRUCTIONS
.

5
Safety Instructions
• Do not use the oor brush without a microber pad
attached to the system.
CAUTIONS
IMPORTANT SAFE TY INSTRUCTIONS
.
ADVICE ON DISPOSAL
1. When this crossed-out bin symbol appears on a product
it means that the product is covered by European
Directive 2002/96/EC
2. All electrical and electronic products should be
disposed of separately from the municipal waste
streamviaspeciccollectionfacilitiesdesignatedbythe
government or the local authorities.
3. Proper disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your municipality, the waste disposal service or the
shop where you purchased the product.
Disposal of your old appliance
INDICATIONS OF USE
This manual can not take into account every possible use.
For further information or for any problems that are not covered in
detail in this manual, please contact the Service Center or retailer.
Keep this manual in a safe place for future reference.
Destroy all plastic bags and packaging material, they can
be a risk for children!
NOTE: Keep the packaging for possible future transport (eg
relocations, repairs, etc.)
Attention: the photographs and/or drawings in this document are for
illustrative purposes only. Actual appliance and the accessories may
vary due to product enhancement.
Safety Information in Digital Format: www.plastecs.it/warning

Product Description
6Product Description
16
6
5
7
8
31
2
18
10
15 17
19
14
13
20
9
21
12
11
4
22
1 - Steam Gun
2 - (2) Extension Tubes
3 - Steam Control Trigger
4 - Floor Brush
5 - Boiler Cap
6 - Power Indicator Light (orange)
7 - Steam Ready Light (green)
8 - Power Switch
9 - Flexible Steam Hose
10 - Shoulder Strap
11 - Filler Funnel
12 - Brush Adapter (2)
13 - Nylon Detail Brush
14 - Stainless Steel Detail Brush
15 - Window Tool
16 - Detail Nozzle
17 - Scraper
18 - Floor Brush Microbre Pad
19 - Small Brush
20 - Small Brush Microbre Pads
21 - Grout Brush
22 - Accessory Storage Bag
Technical Data
Adapter Input: 220-240V~50/60Hz
Cord Length: 7 meters/23 feet
Power: 1450 watts
Boiler: Stainless Steel
Boiler Capacity:1.2 liter/2 pints
Max. Steam Temp.: 130°C/266°F
Max. Boiler Temp.: 4.5 bar

Product Description
7
Product Description - Features
1The Compact Steam Cleaner Features
1. No need for detergents or chemicals. Just add water.
2. Lightweight and compact.
3. Ergonomic, lightweight Steam Gun.
4. Steam Gun locks in as carry handle.
5.Versatile, quick-change accessories.
6. On/Off steam control.
7. Stainless Steel Boiler – non-corroding, reduces calcium buildup.
8. Multiple uses – clean bathrooms, kitchens, living areas, pet areas,
oorsandmuchmore.
Features Cleaner Accessories
5
Features & Cleaner Accessories
The Compact Steam Cleaner Features
1. No need for detergents or chemicals. Just add water.
2. Lightweight and compact.
3. Ergonomic, lightweight Steam Gun.
4. Steam Gun locks in as carry handle.
5. Versatile, quick-change accessories.
6. On/Off steam control.
7. Stainless Steel Boiler –
non-corroding, reduces calcium buildup.
8. Multiple uses – clean bathrooms, kitchens, living
areas, pet areas, appliances and much more.
Accessories - Attachment & Descriptions
A. Connecting Floor Brush Adapter to Floor Brush
1
2
Continued on next page
180°
WARNING:
Always ensure steam trigger is off and not steaming when
attaching an accessory to the unit.
Read and pay attention to all Safety Labels and Product Markings
IMPORTANT
• Do not overll boiler. Read instruction manual before
use.
• Only add tap water or demineralised water to boiler.
• Do not add detergents, oils or any chemicals to the
water, this will cause damage and void the warranty.
DO NOT IMMERSE IN WATER
NOT FOR SPACE HEATING PURPOSES
CAUTION: Water tank is under pressure. Depress handgrip
switch to release pressure prior to removing safety cap. Allow
unit to cool for minimum 5 minutes to relling with water.
Warning: Cap may be hot during use.
CAREFULLY READ INSTRUCTION MANUAL BEFORE USE
WATER TANK HERE
Features

Cleaner Accessories
8Cleaner Accessories
2Accessories - Attachment & Descriptions
A. Attach Brush Adapter to Floor Brush
1. Insert the Brush Adapter in the Floor Brush
The Floor Brush attaches to your Steam Cleaner
using the Brush adapter. Insert the Brush Adapter
in the Floor Brush and turn it 180 ° to lock in place.
2.Attach Floor Brush & Adapter to ExtensionTube
Attach the ExtensionTube to BrushAdapter by
pressing the locking button while sliding Tube into
Brush Adapter. Be sure button and hole line up
and button locks in place.To disconnect, press the
locking button and pull the two pieces apart.
WARNING: Always ensure steam control
trigger is off and not steaming when
attaching an accessory to the unit.
B. Attach Brush Adapter to Small Brush
The Small Brush is used for smaller areas that
the Floor Brush cannot easily reach, such as
cornersofoorsandonstairs.
To use: Insert the Brush Adapter in the Small
Brush and turn it 180° to lock it in place.
EXTENSION TUBE(s)
ThisSteam Cleanercomes withtwoExtensionTubesthat are usedfor
oorcleaningandtoextendthereachoftheSteamCleaner.
180°
180°
180°
180°
180°
180°
BRUSH ADAPTER, FLOOR BRUSH & SMALL BRUSH
The Brush Adapter is used to connect the Floor
Brush and Small Brush to the Steam Cleaner.

Cleaner Accessories
9
Cleaner Accessories
CAUTION: When cleaning windows, always avoid any sudden
changes in temperature to prevent glass breakage or cracks.
To attach Extension Tubes together: Press down the locking
button while sliding Tubes together. Be sure button and hole line up
and button locks in place.
To disconnect Extension
Tubes: Press the locking
button and pull the two
sections apart.
D. ATTACH EXTENSION TUBE TO BRUSH ADAPTER
Once the desired Brush is attached
to the Brush Adapter, press the
lockingbuttonontheExtensionTube
while sliding the Tube in the Brush
Adapter. Ensure the locking button
and the hole on the Brush Adapter
line up.
E. ATTACH WINDOW TOOL
Attach ExtensionTube or Steam Gun to WindowTool
The Window Tool is very useful for cleaning large windows and glass.
To use: Connect Window Tool to
SteamGunorExtensionTubeforhard
to reach surfaces. Apply steam liberally,
rub with soft spongy edge, then remove
excess water and dirt with squeegee
blake. Wipe dirt from squeegee blake
and repeat this process until the
windows are clean.
Press button
Press button
Press button
WARNING: Always ensure steam control trigger is off and
not steaming when attaching an accessory to the unit.
C.ATTACH EXTENSION TUBETO STEAM GUN
To use: Hold down the locking button on the Steam Gun while sliding it
inanExtensionTube.Besurethelockingbuttonlinesupwiththeholeon
theExtensionTubeandbuttonlocksinplace.

Cleaner Accessories
10 Cleaner Accessories
G.DETAIL NOZZLE & ACCESSORIES
Attach ExtensionTube or Steam Gun to Detail Nozzle
1.Attach Nylon or Stainless Steel Brush to Detail Nozzle
The Nylon Detail Brush is best for spot cleaning or tough dirt. Stainless Steel
Detail Brush is best for metal.
To use: Push the Nylon/Steel Detail Brush
ontheendoftheDetailNozzle.
(DetailNozzleshouldbeconnectedtothe
SteamGunorExtensionTubes.)
2.Attach Scraper to Detail Nozzle
The Scraper is best for removing small amounts of wallpaper and also
anythingthatcanbescrapedfromaatsurface,e.g.,greasedepositsinan
oven.Itisalsousefulwhendefrostingfreezers.
To use: Push the Scraper on the end of the
Detail Nozzle. (Detail Nozzle should be
connectedtotheSteamGunorExtension
Tubes.)
3.Attach Grout Brush to Detail Nozzle
The Grout Brush is designed to clean the grout in between tiles. Use on
grouted oors, backsplashes and in showers.
To use: Push the Grout Brush on the end
oftheDetailNozzle.
(DetailNozzleshouldbeconnectedtothe
SteamGunorExtensionTubes.)
*CLICKS to
lock in place.
*CLICKS to
lock in place.
Press button
*CLICKS to
lock in place.
*CLICKS to
lock in place.
Press button
WARNING: Always ensure steam control trigger is off and
not steaming when attaching an accessory to the unit.
F. ATTACH DETAIL NOZZLE
Attach ExtensionTube or Steam Gun to Detail Nozzle
The Detail Nozzle is very useful for
cleaning hard to reach areas. It is ideal for
shower, door and window tracks, shutters
andsanitaryxtures.
To use: Slideandlock DetailNozzleon
theSteamGunorExtensionTube.
*CLICKS to
lock in place.
*CLICKS to
lock in place.
Press button
*CLICKS to
lock in place.

11
Cleaner Accessories
Cleaner Accessories
SMALL BRUSH –
A tted Microbre Pad should be placed over
the bristles of the Small Brush to clean smooth surfaces such as kitchen
cupboards, splash backs, countertops, etc. Fit the Small Microbre Pad
over the bristles and top of Small Brush as shown.
WARNING: The Microbre Pad around the Floor Brush or the
Small Brush can become hot enough to scald or cause burns. Make
sure you let the Pad cool before touching it.
+ =
PAD HOLDERS
H.ATTACH MICROFIBRE PADTO BRUSHES
FLOOR BRUSH –
AMicrobrePadcanbettedontheFloorBrush
to absorb dirt and protect delicate surfaces. It can also be used on vertical
washablesurfacesfollowingthesameprocedureasfortheoor.
1. Place Floor Brush
on Microbre Pad.
2. Fold long sides up,
then insert ends
under Pad Holders.
3. This is how the Floor
Brush should look with
Microber Pad in place.
+ =
PAD HOLDERS
WARNING: Always ensure steam control trigger is off and not
steaming when attaching an accessory to the unit.
I. ATTACH SHOULDER STRAP
Using the detachable Shoulder Strap allows for
greater freedom of movement when both hands are
needed for cleaning tasks or to reach higher places.
To attach Shoulder Strap to the Steam Cleaner,
simply snap Shoulder Strap hooks on the connecting
rings found on unit.
When using Steam Cleaner with the Shoulder Strap, avoid rocking or tilting the
unitexcessivelyasthismaycausewatertoenterthehoseandbedischarged
along with the steam.

Before Use
12 Before Use
WARNING:Always ensure steam control trigger is off and not steaming
when attaching an accessory to the unit.
Use ordinary tap water. Use distilled or demineralized water
if tap water is too hard. DO NOT add detergents, perfumes,
oils or other chemical substances.This will cause damage to
the Steam Cleaner and void the warranty.
*IMPORTANT*
Follow these instructions to avoid overlling the Boiler.
• Be sure the appliance is switched off at the Power Switch and disconnect
the appliance from the power outlet.
• Carefully remove the Boiler Cap by
turning it counter-clockwise.
• Pourinamaximumof1.2litres/2pints
of water using the Filler Funnel provided.
DonotoverlltheBoiler,excesswater
in the Boiler will be ushed out of the
unit, resulting in wet oors or wet surfaces when
cleaning.
• DrysteamwillonlyemitiftheBoilerisnotoverlled.
• Replace the Boiler Cap by turning it clockwise.
• Do not over-tighten the Boiler Cap, nger tight is
sufcient.
• Plug electrical cord into a 3-prong grounded power outlet.
• Turn on the Power Switch.
• The Steam Cleaner will heat up, produce steam and the Boiler will
become pressurised.
• When the green Steam Ready Light turns on the Steam Cleaner is ready
to use. Note: the green Steam Ready Light may turn on and off during
use, this is normal and not a fault.
• If using cold water, heating time is about 6-7 minutes. Using hot water
will reduce the heating time.
7
Before Use & Using Your Steam Cleaner
Before Use
3
4
Filling Steam Cleaner with Water
WARNINGS
•
Carefully read all instructions before removing Boiler Cap.
•
Always switch off the appliance and be sure it has cooled before lling
the Boiler.
Connecting Extension Tube(s)
• Attach one Extension Tube to Steam Gun on Flexible Steam Hose.
• To attach Extension Tubes together, press down the locking button
while sliding Tubes together. Be sure button and hole line up and button
locks in place. To disconnect, press the locking button and pull the two
sections apart.
WARNING:
Always ensure steam trigger is off and not steaming
when attaching an accessory to the unit.
Follow these instructions to avoid overlling the Boiler.
• Be sure the appliance is switched off at the Power Switch and unplug the
appliance from the power outlet.
• Carefully remove the Boiler Cap by
turning it counter-clockwise.
• Pour in a maximum of 1.2 litres / 2
pints of water using the Filler Funnel
provided. Do not overll the Boiler,
excess water in the Boiler will be
ushed out of the unit, resulting in wet
oors or wet surfaces when cleaning.
Dry steam will only emit if the Boiler is not overlled.
• Replace the Boiler Cap by turning it clockwise.
Do not over-tighten the Boiler Cap, nger tight is
sufcient.
• Plug electrical cord into a 3-prong grounded
power outlet.
• Turn on the Power Switch.
• The Steam Cleaner will heat up, produce steam and the Boiler will
become pressurised.
• When the green Steam Ready Light turns on the Steam Cleaner is ready
to use. Note: the green Steam Ready Light may turn on and off during
use, this is normal and not a fault.
• If using cold water, heating time is about 6-7 minutes. Using hot water will
reduce the heating time.
NOTE: Do not turn on Steam Cleaner if Boiler is empty.
*IMPORTANT*
Use ordinary tap water. Use distilled or demineralized water if tap water is too
hard. DO NOT add detergents, perfumes, oils or other chemical substances.
Using Your Steam Cleaner
Max. 1.2l
7
Before Use & Using Your Steam Cleaner
Before Use
3
4
Filling Steam Cleaner with Water
WARNINGS
•
Carefully read all instructions before removing Boiler Cap.
•
Always switch off the appliance and be sure it has cooled before lling
the Boiler.
Connecting Extension Tube(s)
• Attach one Extension Tube to Steam Gun on Flexible Steam Hose.
• To attach Extension Tubes together, press down the locking button
while sliding Tubes together. Be sure button and hole line up and button
locks in place. To disconnect, press the locking button and pull the two
sections apart.
WARNING:
Always ensure steam trigger is off and not steaming
when attaching an accessory to the unit.
Follow these instructions to avoid overlling the Boiler.
• Be sure the appliance is switched off at the Power Switch and unplug the
appliance from the power outlet.
• Carefully remove the Boiler Cap by
turning it counter-clockwise.
• Pour in a maximum of 1.2 litres / 2
pints of water using the Filler Funnel
provided. Do not overll the Boiler,
excess water in the Boiler will be
ushed out of the unit, resulting in wet
oors or wet surfaces when cleaning.
Dry steam will only emit if the Boiler is not overlled.
• Replace the Boiler Cap by turning it clockwise.
Do not over-tighten the Boiler Cap, nger tight is
sufcient.
• Plug electrical cord into a 3-prong grounded
power outlet.
• Turn on the Power Switch.
• The Steam Cleaner will heat up, produce steam and the Boiler will
become pressurised.
• When the green Steam Ready Light turns on the Steam Cleaner is ready
to use. Note: the green Steam Ready Light may turn on and off during
use, this is normal and not a fault.
• If using cold water, heating time is about 6-7 minutes. Using hot water will
reduce the heating time.
NOTE: Do not turn on Steam Cleaner if Boiler is empty.
*IMPORTANT*
Use ordinary tap water. Use distilled or demineralized water if tap water is too
hard. DO NOT add detergents, perfumes, oils or other chemical substances.
Using Your Steam Cleaner
Max. 1.2l
Filling Steam Cleaner with Water
• Carefully read all instructions before removing Boiler Cap.
• Always switch off the appliance and be sure it has cooled
beforellingtheBoiler.
WARNINGS
3

Using The Steam Cleaner
13
Using The Steam Cleaner
• Always drain condensed water from Hose before use or if appliance
has been left idle for a period of time.To drain, direct steam gun
opening into a sink and slide Steam Control trigger on Steam Gun
forward. Once Hose is empty, resume normal use. Never direct the
steam jet toward people, animals or plants.
• Extreme care should be taken when opening the Boiler Cap as it
may become hot during use and escaping steam can cause scalding.
CAUTIONS
4Turning Steam Cleaner ON
• Plug electrical cord into a power outlet.
• Press the Power Switch.
• The Power indicator light (orange) will turn on.
• TheSteamCleanerwillheatupinapproximately6-7minutes.
• When the green Steam Ready Light illuminates, the Steam Cleaner is
ready to use.
• Some water may come out from the steam gun on the attachments.
This is unheated, condensed water in the Hose and is normal.
Steam Release
To release steam from the Steam Cleaner,
slide forward the steam control trigger
found on the Steam Gun. Steam will
continue to be released while the trigger is
in the forward position.To stop the steam,
slide the steam control trigger backward.
5
NOTE: Do not turn on Steam Cleaner if Water Tank is empty.
IMPORTANT: When the Steam Cleaner has run out of
water,steamoutputwillcease.Followrellinstructionsto
use your Steam Cleaner again.
6Relling the Boiler During Use
• ALWAYS vent the Boiler (release all pressure/steam) before
opening Boiler Cap.Venting is done by sliding the Steam Control
Trigger forward to the “On” position. If no steam is emitting then
there is no pressure in the Boiler and the Boiler Cap is safe to
open. Slide back the Steam ControlTrigger to the “Off” position.
• Always unplug the unit and be sure it has cooled off before re-
llingtheBoiler–atleast5minutes.
• NEVER turn on Steam Cleaner if the Boiler is empty!
WARNINGS

Using The Steam Cleaner
14 Using The Steam Cleaner
WARNING: Do not open the Boiler Cap until there is no steam being release
from the Steam Gun. If the Boiler Cap is opened while there is hot steam and
pressure in the Boiler severe burns and injury can occur. If the Boiler Cap is
turned and steam/pressure start to escape from the Steam Cleaner, unplug the
Steam Cleaner from the power outlet and let the unit cool down for at least
15minutesbeforeattemptingtorellorusetheSteamCleaner.
When water in the boiler runs out, steam will stop emitting from the
SteamCleaner.TorelltheBoilerwithwater,followthestepsbelow:
• Switch off the Steam Cleaner by depressing the Power Switch and
unplug the appliance from the power outlet.
• Carefully and slowly turn the Boiler Cap counter-clockwise.If a hissing
sound is heard, residual steam and pressure remain in the Boiler.Wait
until the last of the steam and pressure escapes and the hissing stops
before removing the Boiler Cap.
• Take care of where the Boiler Cap is placed as the underside of the
cap is very hot. Ensure there are no children present who may pick
up the hot cap and cause burns to themselves.
• AllowtheSteamCleanertocoolforatleast5minutesbeforerelling
with water.
• RelltheBoilerwithamaximumof1.2litres(2pints)ofwaterusing
theFillerFunnel.(Note:onlyusetheFillerFunnelsupplied.Itsnozzle
is made from a heat resistant material to prevent it from melting when
llingahotboiler.Otherplasticfunnelscanmeltandbecomewelded
to the inside of the boiler spout, voiding the product’s warranty).
• Be extremely careful when relling, as the interior of the Boiler is
very hot. Water may spurt out as hot water or hot steam causing
burns.
• DonotoverlltheBoiler,excesswaterintheBoilerwillbeushed
outoftheunit,resultinginwetoorsorwetsurfaceswhencleaning.
DrysteamwillonlyemitiftheBoilerisnotoverlled.
• Replace the Boiler Cap by turning it clockwise. Do not over-tighten
theBoilerCap,ngertightissufcient.
• Plug the appliance into a power outlet.
• Turn on the Power Switch.
• The Steam Cleaner will heat up, produce steam and the Boiler will
become pressurised.
• When the green Steam Ready Light turns on the Steam Cleaner is
ready to use. Note: the green Steam Ready Light may turn on and off
during use, this is normal and not a fault.
• If using cold water, heating time is about 6-7 minutes. Using hot water
will reduce the heating time.

Using The Steam Cleaner
15
Using The Steam Cleaner - Maintenance & Cleaning
7Turning Steam Cleaner Off After Use
• To turn Steam Cleaner off, press the Power Switch and unplug the
electrical cord from the power outlet.
• Any remaining water can be left in the unit.
• Use ordinary tap water.
•Werecommendusing distilledordemineralizedwateras thebest
waytocareforandutilizeyourSteamCleaner.
•Iftapwateristoohard,distilledordemineralizedwatershouldbe
used to avoid the risk of sediment and mineral build up in the Boiler.
• Do not add detergents, perfumes, oils or other chemical substances
to the Boiler.This will cause damage to the Steam Cleaner and void
the warranty.
REMINDERS
NEVER HOLDTHE STEAM CLEANER UNDERTHETAP
TO FILL. Use the ller funnel provided to ll the Boiler.
If distilled or demineralised water is regularly used in the Steam
Cleaner, cleaning of the Boiler can be done less frequently. In some
areas tap water is very hard, it is recommended that the Boiler is
cleaned more frequently if hard water is used.
8Cleaning the Steam Cleaner
We recommend you periodically clean the Steam Cleaner to pre-
vent the accumulation of calcium, mineral deposits and other sedi-
mentcausedbytheuseoftapwater.Afterevery10-15rells,llthe
Boiler three-quarters full of hot tap water, shake several times and
empty out the water into a sink. Repeat several times to ensure that
theBoilerisushedofanycalciumormineraldeposits.Wipethe
Steam Cleaner with a damp cloth and dry.
The cleaning of the Boiler and Steamer is the sole
responsibility of the appliance owner. Calcium, mineral
deposits and other sediments left to build up in the Steam
Cleaner causing it to fail and/or the steam pathways in
the Steam Cleaner to block, is not covered by the product
warranty. Users must follow the cleaning instructions above.
Maintenance & Cleaning

Maintenance & Cleaning
16 Maintenance & Cleaning - Tips & Reminders
Steam Cleaner Tips & Reminders
This steam cleaning appliance has many practical uses that have
not been mentioned in this manual. Please contact the Customer
Support Line for tips and suggestions of where and how to use
the Steam Cleaner. Alternatively visit the website for additional
information.
Steam cleaning allows the user to clean chemical-free by using the
power of steam, in place of harsh chemical-based detergents. The
heat from the steam softens and loosens dirt on surfaces, while the
steam pressure lifts the dirt away. All that is left to do is to wipe the
surfacetoremovethedirtandmoistureusingamicrobreclothor
by using a cleaning cloth if the surface is soiled or greasy.
TIP: to get the best cleaning results use a microber pad to wipe
the dirt and moisture from the surface being cleaned. Microber is
designed to pick up and hold dirt,a great aid in lifting and removing
the dirt that the steam cleaner has softened and loosened. Also,
Microber requires moisture to glide over surfaces, the steam
cleaner provides moisture that the Microber needs to glide.
Microber and Steam are a great cleaning combination!
10
Replacement of Brushes, Microber Pads
and Accessories
TheNylonandStainless SteelDetailBrushes andtheMicrobre
Pads for the Small Brush and Floor Brush provided with the
Steam Cleaner are to get you started using your Steam Cleaner.
Asthesebrushesandmicrobrepadsbecomedirtyorwearout,
replacementbrushesandmicrobrepadscanbepurchasedfrom
the retailer from which you purchased your Steam Cleaner and/
or from most other electrical appliance retail outlets. It is normal
tohavereplacementsofthebrushesandmicrobrepadscloseat
handwhilecleaningasthebrusheswearoutorthemicrobrepads
become dirty.
Any of the other accessory tools are replaceable by contacting
Euroexonthewebsite.
9
The Steam Cleaner is intended for domestic household use only.
It is not intended for commercial use. Any use other than for
domestic household purposes will void the product warranty.
Tips & Reminders

Tips & Reminders
17
Tips & Reminders
Water
Use ordinary tap water for all cleaning. In hard water areas, we
recommend distilled or demineralised water to reduce the formation
of calcium and other mineral deposits in the Steam Cleaner. Use
distilled or demineralised water when steaming light coloured fabrics
to eliminate the possibility of hard water stains.
IMPORTANT: Do not add cleaning solutions, perfumes, oils
or any other chemicals to the water used in the Boiler.
Temperature
The temperature in the stainless steel Boiler reaches about 130°C.
Thesteamtemperaturejustoutsidethetipofthenozzle/accessory
is between 105°C and 115°C. The temperature of the steam falls
to 38°C at a distance of 25cm from nozzle.This Steam Cleaner
produces a drier steam which cools very rapidly to avoid burns and
injuries. Steam must make direct contact with surfaces for it to clean
effectively.
TIP: the hot steam can be used to kill dust mites in soft
furnishings and mattresses.The Steam Cleaner is ideal for
asthma sufferers, persons with skin sensitivities and anyone
with chemical sensitivities.
Making Contact with Surfaces
The steam is at its hottest just as it leaves the nozzle/accessory.
This is the area of the steam output that should be used to clean to
achievemaximumperformance.Allaccessoriesshouldmakedirect
contact with the surfaces being cleaned to transfer the heat from
the Steam Cleaner to the surface in order to soften and loosen dirt.
If the accessory being used does not make contact with the surface,
the desired results may not be achieved. If assistance is required
contact our Customer Support Line.
TIP: steam will clean hard, sealed, non-porous surfaces in place of
harsh chemical-based cleaners and detergents. For soft furnishings
such as carpets, rugs, lounges, children’s toys etc, steam will refresh
and deodorise the bres. Steam is not used to clean carpets, other
than to spot clean.To clean carpets proper carpet cleaning equipment
should be used.

Maintenance & Cleaning
18 Maintenance & Cleaning
Microber Pad Care & Cleaning
YourMicroberPadsaredesignedforhundredsofuses.WashPads
regularly, either by hand washing (using mild soap and warm water)
or in your washing machine on a delicate cycle, cool water. Never
use fabric softener or bleach. We recommend letting Pads air
drytomaintainmaximumlongtermeffectiveness.
Replacement pads are available at most retail outlets or on the
Euroexwebsiteatwww.euroex.com.au.
Microber washing instructions
11
MICROFIBER FLOOR PAD
75% Polyester / 25% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric soener
MICROFIBER BRUSHES PADS
90% Polyester / 10% Polyamide
Hand wash only
Tumble dry low or air dry
No bleach / No fabric soener

19
Troubleshooting
Troubleshooting
ISSUES POSSIBLE CAUSES SOLUTIONS
Steam is not coming out of
the Steam Nozzles
Improper Handle Assembly Call Customer Service to receive instrucons to correct
the problem
Why does the Green Steam Ready Light turn o when I’m
using the Steam Cleaner?
Euroex Steam Cleaners have a Thermostat Tempera-
ture Control. When the correct temperature in the
boiler is reached, the thermostat cuts o power, making
this appliance more energy ecient.
When should I replace my Microbre pads? It will depend on how oen you use your Pads and how
well you wash & maintain them. Use mild soap and
water to hand wash or a gentle cycle on the washing
machine. Allow to air dry. Never use fabric soener or
bleach.
The steam seems to be
making my oor too wet
Front Steam Jets are being
used too frequently
Only use Front Steam Jets in short bursts for cleaning
tougher dirt or to clean hard to reach areas
The Cleaning Pad is too wet
(saturated with moisture)
Replace the wet Pad with a dry, clean Pad and connue
cleaning
Troubleshooting
12

M6S 09-2020
Customer Support
Customers needing assistance with their Steam Cleaner can call the Customer Support Line
on the phone numbers listed below. Customers should also call the Customer Support Line if
they require product warranty repair or post-warranty product servicing. Our friendly Customer
Service Team can assist you with getting the best cleaning results from your Steam Cleaner or
they will provide helpful steam cleaning tips, too.
Customer Support Line
AUSTRALIA 1800 663 866
NEW ZEALAND 0800 666 783
Euroflex Australia Pty Ltd
79 Furniss Road
DARCH WA 6065
AUSTRALIA
TEL: 08 9302 2526
Email: [email protected]
Website: www.euroflex.com.au
Euroflex New Zealand Ltd
c/- Dubins
137 Glenfield Road
Birkenhead Auckland 0626
NEW ZEALAND
TEL: 0800 666 783
Email: [email protected]
Website: www.euroflex.com.au
Plastecs SRL
Via dei Colli, 59
31058 Susegana (TV)
ITALY
Tel: +39 0438 453334
Email: [email protected]
Website: www.euroflex-appliances.com
Table of contents
Other Euroflex Steam Cleaner manuals

Euroflex
Euroflex VAPOUR M4S User manual

Euroflex
Euroflex vapour M2R User manual

Euroflex
Euroflex monster mop User manual

Euroflex
Euroflex Monster Superclean EZ2-S User manual

Euroflex
Euroflex VAPOUR M4S User manual

Euroflex
Euroflex monster SC50 User manual

Euroflex
Euroflex SC4X2 AUS User manual

Euroflex
Euroflex monster SC35 PLUS User manual

Euroflex
Euroflex Steam Shark User manual

Euroflex
Euroflex Monster EZ1 User manual