EUROSTER 10PC User manual

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 1
EUROSTER 10PC
CH PUMP CONTROLLER FEATURING HEATING SOURCE CONTROL
Manual version: 01.08.2023
MANUFACTURER: P.H.P.U. AS, Chumiętki 4, 63-840 Krobia, Poland
1. INTRODUCTION
In order to ensure proper operation of the controller and the CH system, please read this
manual carefully.
2. APPLICATION
EUROSTER 10PC is designed to control the CH circulating pump and to switch on the
heating source (voltage-free contact). The controller is equipped with an input to connect
a room thermostat and two temperature sensors (one for the heating source and one for
the heating zone).
The controller may be used in the following systems:
•With a heat pump, to control the CH pump with a buffer tank
•Floor heating equipped with a thermostatic mixing valve
•Heating systems, to switch on the CH pump with an activation temperature
3. CONTROLLER FUNCTIONS
•Controls a CH circulating pump
•Controls a heating source
•Cooperates with a room thermostat
•Protects the heating system against overheating – a preset alarm temperature for
a heating zone and supply
•Measures the heating source temperature
•Features a function that protects the system against freezing
•Prevents seizure of the pump – Anti–Stop function
•set of sensors included
•Installation in an electric cabinet (6 modules) on a DIN 35 mm rail.
EUROSTER 10PC controller is equipped with an Anti-Stop system that prevents the process
of scale build-up on the unused pump rotor. It automatically turns the pump on every
14 days when the heating season is over. Keep the controller turned on to allow the function
to operate after the heating season.

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 2
4. VISIBLE ELEMENTS OF THE CONTROLLER
1. Controller’s power connection – 230 V 50 Hz
2. Output for connecting the CH pump 230 V 50 Hz
3. Output for connecting heating source (change-over voltage-free contact)
4. Connector for temperature sensors and room thermostat
5. Confirm and switch-on/off button
6. Button – increase the setting
7. Button – decrease the setting
8. LCD
The display backlight turns off by default after one minute following the end of the control-
ler operation. The controller enables turning the permanent backlight on.
5. THERMOSTAT INSTALLATION
GENERAL SAFETY RULES
•Prior to the commencement of any installation works read this manual
carefully! Incorrect installation and improper use may lead to serious haz-
ards to users or other persons and result in property damage!
•Prior to mounting or dismantling and maintenance of the controller, make
sure that it is de-energized!
•Dangerous voltages, hazardous to life, may be present on the controller
and its cables, therefore only qualified technicians holding authorization
for electrical works may be entrusted with the installation of the controller!
•The electric connections performed and cables used shall be adequate to
the applied loads and must conform to all requirements!
•Do not install the controller in rooms of increased humidity, substantial
dustiness or with the presence of caustic or flammable vapours, protect it
against water and other liquids!
•Do not install any controller showing signs of mechanical damage!
•The controller is not a safety component of the heating system. Additional
protection devices must be used in the heating systems prone to the risk
of damage due to failure of the control systems!
•When connecting the power cables, pay particular attention to the correct
connection of PE conductors.
•Do not misuse the controller!
•The device is not intended for use by children!
•Failure to meet the safety and maintenance rules results in loss of war-
ranty!
Install the controller in a place where the temperature does not exceed 40°C. Lead all
necessary cables prior to mounting the controller.

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 3
Screw the electric cables to the connectors according to the description and drawing. Make
sure to keep the proper designation of the cables. Screw the neutral conductors to N ter-
minals, phase conductors to L terminals and grounding conductors to PE terminals. Use a
cable with a minimum diameter of 0.75mm² for connection.
CAUTION!
When connecting the power cables, pay particular attention to the correct con-
nection of PE conductors.
The temperature sensors are not suitable to be immersed in liquids.
CAUTION!
Euroster 10PC controller and a heat emitting device connected to the “Boiler”
output must be powered from the same phase of the power system.
a) Connection Diagram

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 4
b) mounting the controller
•Install the controller in an electric cabinet (width of 6 modules) on a DIN 35 mm
rail
•using fasteners fix controller cables to the wall.
c) Connecting a Room Thermostat
The controller can cooperate with any room thermostat with voltage-free, normally open
(NO) output – e.g. any thermostat manufactured by EUROSTER.
Connection of the controller:
•Make sure that the controller is de-energized.
•Remove the jumper from the REG joint
•Lead a cable (minimum 2 x0.5 mm² stranded wire) between the room thermostat
(or the receiver – in case of connecting the wireless version) and the EUROSTER
10PC controller and insulate the cables
•Screw the cables to the joint.
•connect the cables to COM and NO contacts in the room thermostat.
d) Connecting Temperature Sensors
The controller temperature sensors may be connected in any way, with no need to
keep cable polarity. At installation avoid leading the sensors parallel to live cables.
Moreover, make sure to provide the proper contact with measured surfaces.
•Install the heating source temperature sensor on the heating source/buffer or the
uncovered outlet pipe of the CH boiler (possibly close to the boiler),
•Install the heating zone temperature sensor on the uncovered pipe downstream of
the CH zone pump.
•Use the hose clips to tighten the sensors to the pipe and insulate them.
e) BOILER output
It is used to switch on the heating source, e.g. gas-fired boiler. It has 3 contacts marked
as NO, COM and NC. They are galvanically isolated from the rest of the system. They
withstand a mains voltage of 230 V and a load of 1 A.
Most commonly, boilers are equipped with the normally open connection (a jumper
must be removed from the heating source), in such cases, you need to connect the
10PC controller with COM and NO terminals (the controller has the COM and NO ter-
minals).
The BOILER output is disconnected whenever the room thermostat achieves the preset
temperature or the supply temperature alarm occurs.
f) Connecting the CH pump
•Connect the yellow or yellow-green wire (protective conductor) to the PE terminal
•connect the blue core to the (N) terminal,
•connect the brown wire to the terminal (L);
g) Connecting the controller to 230 V 50 Hz network
Check the wires and sensors for the correct connection. Having secured the cables
against accidental breaking, connect the power cable to the 230 V 50 Hz mains socket
with an earth pin.

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 5
6. MOUNTING TEMPLATE
The following diagram is simplified and does not cover all the elements necessary for the
correct operation of the system.
1. EUROSTER 10PC Controller
2. Heating zone, e.g. floor heating
3. Heating zone temperature sensor
4. CH pump
5. Heating source temperature sensor
6. Heating device, e.g. gas boiler
7. Room thermostat (option)
7. SWITCHING THE CONTROLLER ON/OFF
•After connecting the plug into the 230 V power socket, the number of program
version is displayed for 2 sec.
•Anti-Stop system turns on the pump – AS letters blink and the system status is
displayed
•In order to switch the controller off, hold „√” for 3 seconds – St letters (STOP)
appear, and similarly, during switching-off, the system status is displayed.
CAUTION!!! The controller has an electronic switch, which does not guarantee a
safe de-energizing of cooperating equipment. Disconnecting or short-circuiting
the sensor cables during installation, in particular, may cause an emergency
switch-on of the outputs. Before starting any work with the controller installa-
tion, make sure to disconnect the power supply!

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 6
8. DISPLAY DESCRIPTION
Active elements of the display are presented below:
1. Name of the set parameter – displayed while previewing or changing param-
eters
2. Heating source (boiler) temperature sensor icon
3. Test operation icon – displayed during manual control
4. Alarm icon – blinks in case of alarm
5. Furnace status illustration – shown with active heating source (BOILER) out-
put, disappears when the room thermostat input is open.
6. Room thermostat input status signal – active when the thermostat switches
the heating on
7. Heating source (boiler) temperature / Value of the displayed parameter
8. Temperature of the heating zone / Menu item number
9. Pump icon – visible during pump operation
10. CH temperature sensor icon
9. RESTORING FACTORY SETTINGS / PERMANENT LIGHT-UP OF THE DISPLAY
Proceed as follows to restore factory settings or change the operation mode, if needed:
•While holding the √ button pressed, momentarily unplug and then reconnect the
plug to the 230 V mains socket
•“Fd” letters (factory defaults) are displayed and 0 appears after releasing the but-
ton,
•Use buttons to select 0 or 1 and confirm with √.
Selecting 0 enables the change of screen backlight functions without restoring fac-
tory defaults. Selecting 1 restores factory settings.
•Then, “bl” (backlight) is displayed and 0 appears after releasing the button.
•Use buttons to select the required number (0 or 1). Selecting 0 results in the
automatic screen backlight switch-off after 1 minute of finishing operating the con-
troller, and selecting 1 results in the display backlight being continuously active.
•Control and correct the remaining controller settings, if necessary.
•In case of failure to confirm the changes within 5 seconds, the controller resumes
operation without introducing changes.
10. CONTROLLER SETTINGS
After being switched on the controller shows the system status. Press to enter preview
and setting change mode.
The controller configuration is specified below: press buttons to select the desired pa-
rameter. The controller will show the value (at the top) and number (at the bottom). In
order to change the value of the displayed parameter, press √ (the parameter value starts

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 7
blinking), set the required value using , and confirm the selection by pressing √. If the
current value is to remain unchanged (cancelling changes), do not press the button, but
wait 10 seconds until the setting stops blinking.
To facilitate the operation of the controller, the configuration windows have been numbered.
The user can change the following parameters:
1. CH pump operation temperature
When the temperature in the supply sensor is exceeded, the CH pump output is
switched on.
2. Hysteresis
It indicates the temperature difference at which the controller turns the CH pump
on and off. The conditions for turning the pump on and off are specified in section
11.
3. Temperature of Supply Alarm
Exceeding the alarm temperature on the system’s supply triggers the alarm algo-
rithm, which aims to cool down the heating device. The alarm algorithm heats the
zone to a temperature close to the alarm threshold. It is essential to ensure that
the alarm temperature is at a safe level.
4. Alarm temperature of the CH zone.
This setting allows you to establish the temperature at which the alarm procedures
are activated. If the controller is used in a floor heating system, it is recommended
to set it at 45 ºC.
Caution! Alarm temperatures for zones should be selected carefully. Incorrect set-
ting of temperature level may cause improper operation or major failure of the
system components.
5. Minimum operating time of the heating source
If the room thermostat switches on for a period shorter than this setting, the boiler
and pump transmitters will remain switched on for a period equal to this setting.
The operating time (minutes) preset here determines also the delay in the CH
pump switch-off.
Switching off the room thermostat (REG output open) results in switching off the
BOILER input, while the output of the CH pump is switched off after the lapse of
the preset time.
6. Read-out Correction – the Heating Source Temperature Sensor
It is a value added to the measured temperature value. It allows for compensating
the difference in readings between the sensor placed on the pipe and the ther-
mometer installed on the boiler.
7. Read-out Correction – the Heating Zone Temperature
It is a value added to the measured temperature value. It allows for compensating
the difference in readings between the sensor placed on the pipe and the heating
medium.

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 8
8. Pump Operation/Test
Displays the current status of the pump calculated by the controller (0 or 1).
To operate the pump manually press the button and change the displayed value.
After 10 seconds of inactivity or pressing the knob again, the controller resumes
operation according to the settings.
9. Heating Source Operation/Test
Displays the current status of the heating source transmitter, calculated by the
controller (0 or 1). To operate the pump manually press the button and change the
displayed value. After 10 seconds of inactivity or pressing the button again, the
controller resumes operation according to the settings.
ATTENTION: In case the set values preclude the correct operation of the control-
ler, the alarm icon will appear on the display, and the colliding settings will be
displayed alternately. After a few seconds, the last correct configuration is re-
stored.
All settings are listed below:
Setting
Value
unit
Name
No.
Default
Min.
Max.
CH pump activation temperature
1
28
10
80
°C
Pump hysteresis
2
4
2
20
°C
Temperature of Supply Alarm
3
90
80
110
°C
Alarm temperature of the CH
zone.
4
50
30
90
°C
Heating source operating time
5
2
0
60
min.
Correction of the heating source
temperature sensor read-out.
6
0
-5
5
°C
Correction of the CH zone
temperature sensor read-out.
7
0
-5
5
°C
Pump operation/test
8
- 1)
0 2)
1 2)
-
Heating source operation/test
9
- 1)
0 2)
1 2)
-
1) The displayed value is calculated by the controller,
2) 1 stands for activation, and 0 stands for deactivation.
11. CONTROLLER OPERATION
The controller controls the temperatures of the boiler and the CH zone. Periodically, it
calculates the difference between the preset and measured temperature.
The pump is switched on once the pump activation temperature (parameter 1) is exceeded,
and it is switched off when the temperature drops below the set value by the hysteresis
(parameter 2).
12. ANTI-FREEZE PROTECTION
The anti-freeze protection is activated when the temperature of a given sensor drops to
4°C. If such temperature is detected by a sensor, the pump is activated and “AF” (anti-

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 9
freeze) appears on the display. The protection is turned off when the temperature rises to
6°C.
13. OPERATION WITH ROOM THERMOSTAT
Turning off the room thermostat (opening the output) will cause the heating source trans-
mitter to turn off, followed by switching off the pump.
The connection of a room thermostat was described in point 5c.
14. ANTI-STOP
Each time the controller is connected to a 230 V network (also after restoring factory set-
tings or changing the backlight type), the Anti-Stop function immediately activates the
pump, later the operation is repeated every 14 days. During its operation, "AT" letters flash
at the display.
If an alarm situation (overheating or sensor damage) occurs when the Anti-Stop system
is active, the operation of the Anti-Stop system will be ceased.
15. TROUBLESHOOTING
The device does not work
Burnt fuse or ROM failure – send the device to the service.
The display and the sensor icon blink, "Sh" or "OP" letters appear
The sensor is shorted (Sh) or opened (Op) – check the cable of the sensor, whose icon is
flashing or send the device along with the sensors to the service centre.
The pump does not work
The device is turned off – make sure that the proper icons are displayed. If not – check
the settings. Restore factory settings (section 9).
Wrong connection – check.
16. SIMPLIFIED DECLARATION OF EU CONFORMITY
P.H.P.U. AS AGNIESZKA SZYMAŃSKA-KACZYŃSKA hereby declares that the type of EU-
ROSTER 10PC equipment conforms to the following directives: 2014/35/EU (LVD),
2014/30/EU (EMC), 2011/65/EU (RoHS).
The complete text of the Declaration of EU conformity is available at the following Internet
address: www.euroster.pl.
17. TECHNICAL DATA
Controlled device: CH pump
Supply voltage: 230 V 50 Hz
Maximum output load: 100 W
Maximum power consumption: 2 W
Temperature measurement range: -30ºC... +110ºC
Zone temperature control range: +10ºC... +80ºC
Temperature control accuracy: 1ºC
Hysteresis range: 2ºC... 20ºC
Operating temperature +5ºC... +40ºC
Storage temperature: 0ºC... +55ºC
Ingress protection rating: IP20
Installation method: protective cabinet – DIN 35 mm rail
Warranty period: 2 years
Dimensions (width/height/depth) in mm: 106 /90 /59
Line protection: WTA-T 3.15 A time-lag fuse (inside the device).

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 10
18. KIT CONTENTS
b) Euroster 10PC Controller
c) Controller power cable: 2 m
d) Heating zone temperature sensor: 3 m
e) Heating source temperature sensor: 3 m
f) Sensor hose clips: 2 pcs.
g) Installation and Operation Manual with Warranty Certificate
19. ELECTRONIC WASTE MANAGEMENT INFORMATION
This product is designed and manufactured from high-quality materials and
components suitable for reuse. If the equipment, packaging, user manual,
etc. is provided with a crossed-out wheelie bin symbol, it means that the
product should be selectively collected in accordance with the Directive
2012/19/EU of the European Parliament and of the Council. Such marking
informs that the electrical and electronic equipment may not be disposed of together with
other household waste after their service life. The user is obliged to take the used devices
to a point of collection of waste electrical and electronic equipment. The entities collecting
such equipment, including the collection points, shops, and municipal entities, set up an
appropriate system enabling the handover of such equipment. The proper disposal of waste
equipment contributes to the prevention of dangerous consequences to nature and human
health, resulting from the possible presence of hazardous components in the equipment
and from inaccurate storage and processing of such equipment. Selective collection con-
tributes to the recovery of materials and components used for manufacturing the equip-
ment. A household plays an important role in contributing to reuse and recovery including
recycling, of the waste equipment. The attitudes influencing the protection of the common
good of a clean environment are shaped at this level. Households are also one of the larger
users of small equipment and its rational management at this stage impacts the recovery
of recyclables. Inaccurate disposal of this product may be penalized in accordance with
national legislation.
MAINTENANCE
Before each and every heating season, the control module must be cleaned of any dust
and other dirt, the cables must be checked for their technical condition and tight fixing.
Do not use solvents and aggressive detergents to clean the controller, since they may
damage the surface of the housing. If necessary, wipe it carefully with a soft cloth.

EUROSTER 10PC – INSTALLATION AND OPERATION MANUAL 11
WARRANTY CERTIFICATE
EUROSTER 10PC CONTROLLER
Warranty terms:
1. The warranty is valid for 24 months from the device's sale date.
2. The claimed module along with this warranty certificate must be supplied to the
seller.
3. Warranty claims shall be processed within 14 business days from the date the
guarantor has received the claimed device.
4. The device may be repaired exclusively by the guarantor, manufacturer or by other
parties clearly authorized by the manufacturer.
5. Warranty becomes void in case of any mechanical damage, incorrect operation and
repairs made by unauthorized persons.
6. This consumer warranty does not exclude, restrict nor suspend any right of the
buyer if the product does not meet any of the sale contract terms.
……..........................................................................................................................................
Sale date
Serial number / date of manu-
facture
stamp and signature
service: telephone No.
(65) 57-12-012
The business entity that issued this warranty certificate (the guarantor) is:
P.H.P.U. AS Agnieszka Szymańska-Kaczyńska, Chumiętki 4, 63-840 Krobia, Poland