Evelo Omega User manual

EVELO Omega Assembly
Our Team is here to help 7 days a week
[e-mail] |877-991-7272
Feel free to reach out!
The focus of this document is to assist with the assembly of your new EVELO
Omega. The scope is intentionally narrow – The “User Guide” that was
included with your bike covers a much broader spectrum of topics: fit adjust-
ments, battery care, controls etc.
Watch the Assembly
Instructions Video

2ASSEMBLY OF EVELO ATLAS
1Begin unboxing the bike by cutting the banding then
opening the box. Use caution regarding the staples as
they can be very sharp. Remove the small boxes.
Laying the box on its side and
sliding the bicycle out of the
box is a great technique if you
are unable to li the bike.
3Carefully remove all packing material from
bike, avoid using sharp objects as to protect
the paint.
4Tools and User Guides will be in the small
black Evelo box. The pedals will be in a
small cardboard box.
3Lower kickstand to keep bike upright
during assembly.
2
Unboxing Your EVELO

3ASSEMBLY OF EVELO ATLAS
1
Slide bolt through headlight, fender, and fork.
Attach headlight and fender assembly to fork. Position the fender as high up as possible and tighten the
bolt and nut.
3
4
Install Fender and Headlight
Remove bolt from front fork assembly.

4ASSEMBLY OF EVELO ATLAS
Remove thru-axle from fork. Use an allen wrench to unscrew the axle from the le side of the fork and slide
it out.
1
Install Front Wheel
Put front wheel into place. Li the fork, place the wheel most of the way in the fork, then carefully line up
the brake rotor with the slot between the brake pads and mount the wheel fully into the fork.
2
Slide the thru-axle into the fork and wheel and securely tighten with an allen wrench.
3

5ASSEMBLY OF EVELO ATLAS
Remove bolts from each side of fork and attach lower fender support struts.
4
Mount Fender
Make sure to install washer and spacer as shown.
6
Tighten fender support strut hardware.
7

6ASSEMBLY OF EVELO ATLAS
Rotate Fork: rotate the steering assembly
so that the cables aren’t wrapped around
the frame and the fork is facing forward.
When seated on the bike, the brake caliper
should be to the le of the rider.
1
Install Handlebars
Tighten stem top bolt to medium tension so
that spacers no longer rotate.
3
Remove the screws on top of the stem faceplate. Keep Track of the parts.
5
Loosen the stem clamp bolts and rotate the
stem so it points forward. There is one bolt on
each side of the stem.
2
Re-tighten bolts on both sides of the stem.
4

7ASSEMBLY OF EVELO ATLAS
Install Handlebars
7
Place handlebars in cradle, aligned with center and grips level. Replace faceplate and tighten screws on
top of handlebars
6
Loosen bolts along stem and align handlebars. Double-check that spacers do not rotate and tighten stem
top bolt as needed. Re-tighten bolts on sides of stem.
7Loosen bolts along stem and align handlebars. Double-check that spacers do not rotate and tighten stem
top bolt as needed. Re-tighten bolts on sides of stem.

8ASSEMBLY OF EVELO ATLAS
Install Pedals
Screw pedals into crank arms securely. Installation of the pedals requires a 15 mm wrench.
There is an L and an R stamped into the end of each pedal for reference.
1
It is important to note that the pedals are threaded differently. The right pedal screws in
clockwise and the le pedal screws in counter-clockwise.
2

9ASSEMBLY OF EVELO ATLAS
Use of Battery
Two copies of the key come attached to
the handlebars.
1
The battery is heavy, please be careful. When reinstalling, push the battery into
place firmly.
3
Power up the bike and you’re ready to ride!
5
Use the key to unlock the battery, the battery
releases downward.
2

10ASSEMBLY OF EVELO ATLAS
Serial Number Location
To register your bike on our website, you will
need to record the serial number. It is located
on the headtube of your bike, just above the
front fork.

There is considerable additional information in your “User Guide”.
Of course, if you ever have questions, our team is ready to help!
Our Team is here to help 7 days a week!
[e-mail] | 877-991-7272
Feel Free to reach out!