Event Lighting LM180 User manual

LM180
180W LED SPOT HEAD
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are
subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions.
Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

2
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent
surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity
may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher
temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing
(anticlockwise).

3
www.event-lighting.com.au
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

4
www.event-lighting.com.au
Product Installation
This device can be mounted in many orientations
provided each individual device is secured by the use of
correct mounting bracket.
Use a safety chain when mounting this device overhead.

5
www.event-lighting.com.au
Dimensions
Lux Chart
Lux Chart @ 16°
2.5m 5m 7.5m 10m 20m
Ø0.70 Ø1.41 Ø2.11 Ø2.81 Ø5.62
19,120 4,780 2,150 1,210 540

6
www.event-lighting.com.au
Colour Wheel
Red
Dark Blue
Green
Yellow
Magenta
Blue
Orange
Open

7
www.event-lighting.com.au
Static Gobo Wheel
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6
Position 7
Position 8

8
www.event-lighting.com.au
Rotating Gobo Wheel
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6

9
www.event-lighting.com.au
Menu operation
Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select / Move down a level.
Menu
MENU
DESCRIPTION
Function
Mode
DMX Address
A001~AXXX
DMX Address Setting
Channel Mode
CH14
14 Channel Mode
CH16
16 Channel Mode
Auto Run
Internal Program1~8
Internal Program
State: Master/Alone
Auto Run State
Auto Run (On/Off)
Toggle Auto Run
Music Control
Internal Program1~8
Internal Program
State: Master/Alone
Sound Control State
Music Run (On/Off)
Toggle Sound Control
Option
Reset Default
Yes/No
Reset to Default Setting
Signal Set
DMX
Wireless DMX
Wireless TX
Wired DMX
Wireless DMX Receiver
Wireless DMX Transceiver

10
www.event-lighting.com.au
Pan / Tilt
Reverse Pan (On/Off)
Reverse Tilt (On/Off)
Select Pan 630°/540°/360°
Select Tilt 270°/180°/90°
Limit Mode OFF/CEN./R/L
Reverse Pan
Reverse Tilt
Pan Degree(540°)
Tilt Degree(270°)
Select Edge or Corner Range
UI SET
Mic Sens. 0~99%
Hold on no DMX(On/Off)
Half Colour (On/Off)
Flip Display (On/Off)
Microphone Sensitivity Setting
Hold or no hold When no Signal
Select half Colour
Flip Display
Informati
on
Temperature
XXX℃/℉
Current Temperature
Software
Version
V1.0~V9.9
Current Software Version
Manual
Control
Reset
All
Pan/Tilt
Colour
Gobo
Others
Reset all Settings
Reset Pan/tilt Settings
Reset Colour Settings
Reset Gobo Settings
Reset Other Settings
Channel
PAN=XXX……
Manual Control Channel
ADVANC
ED
(Access
Code
088)
Calibration
PAN=XXX……
Calibration

11
www.event-lighting.com.au
DMX Chart
Mode/Channel
Value
Function
14CH
16CH
1
1
Pan
0..255
Pan movement
2
2
Pan Fine
0..255
Fine control of pan movement
3
3
Tilt
0..255
Tilt movement
4
4
Tilt Fine
0..255
Fine control of tilt movement
5
5
Colour
0..15
Open / white
16..31
Colour 1
32..47
Colour 2
48..63
Colour 3
64..79
Colour 4
80..95
Colour 5
96..111
Colour 6
112..127
Colour 7
128..189
Forward rainbow effect, fast to slow
190..193
Colour rotation stop
194..255
Reverse rainbow effect, slow to fast
6
6
Rotation Gobo
0..9
Open
10..19
Gobo 1
20..29
Gobo 2
30..39
Gobo 3
40..49
Gobo 4
50..59
Gobo 5
60..69
Gobo 6
70..89
Gobo 1 shake slow to fast
90..109
Gobo 2 shake slow to fast
110..129
Gobo 3 shake slow to fast
130..149
Gobo 4 shake slow to fast
150..169
Gobo 5 shake slow to fast
170..189
Gobo 6 shake slow to fast

12
www.event-lighting.com.au
190..255
Forward wheel spin,slow to fast
7
7
Rotation Gobo
0..3
TBD
4..127
Forward gobo rotation, fast to slow
128..131
Gobo rotation stop
132..255
Reverse gobo rotation, slow to fast
8
8
Static Gobo
0..14
Open
15..29
Gobo 1
30..44
Gobo 2
45..39
Gobo 3
60..74
Gobo 4
75..89
Gobo 5
90..104
Gobo 6
105..119
Gobo 7
120..134
Gobo 8
135..144
Gobo 1 shake slow to fast
145..154
Gobo 2 shake slow to fast
155..164
Gobo 3 shake slow to fast
165..174
Gobo 4 shake slow to fast
175..184
Gobo 5 shake slow to fast
185..194
Gobo 6 shake slow to fast
195..204
Gobo 7 shake slow to fast
205..214
Gobo 8 shake slow to fast
215..255
Forward wheel spin, slow to fast
9
9
Shutter
0..31
Shutter closed
32..63
Shutter open
64..95
Strobe effect slow to fast
96..127
Shutter open
128..159
Pulse effect, slow to fast
160..191
Shutter open
192..223
Random strobe effect, slow to fast
224..255
Shutter open
10
10
Dimmer
0..255
Dimmer 0%...100%
11
11
Focus
0..255
In(near) to out(far)
12
12
Rotating prism, Prism
0..5
OFF
6..127
ON

13
www.event-lighting.com.au
128..189
Forward rotation, fast to slow
190..193
Prism rotation stop
194..255
Reverse rotation, fast to slow
13
13
Speed pan/tilt
0..225
Pan/tilt speed, fast to slow
226..235
Blackout during pan/tilt functions
236..245
Blackout when colour and gobo switching
246..255
TBD
14
14
Special Function
0..19
TBD
20..29
TBD
30..39
TBD
40..79
TBD
80..84
Reset all
85..87
Reset scan
88..90
Reset colour
91..93
Reset gobo
94..96
TBD
97..99
Reset other motor
100..109
Internal program 1
110..119
Internal program 2
120..129
Internal program 3
130..139
Internal program 4
140..149
Internal program 5
150..159
Internal program 6
160..169
Internal program 7
170..179
Internal program 8
180..189
Internal sound program 1
190..199
Internal sound program 2
200..209
Internal sound program 3
210..219
Internal sound program 4
220..229
Internal sound program 5
230..239
Internal sound program 6
240..249
Internal sound program 7
250..255
Internal sound program 8
Vector
Mode
Value
Function
15
Colour Time
0..255
Colour speed, fast to slow
16
Gobo Time

14
www.event-lighting.com.au
0..255
Gobo speed, fast to slow
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to
receive instructions from the external controller. For independent control, each fixture must be
assigned its unique address control channels. For example, this device has two channel modes:
14/16, if we set the mode at standard 16 channels mode, and there are several models need to be
independently controlled, we just simply address first fixture at 1, and second fixture at 17, third one at
33, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.

15
www.event-lighting.com.au
More Functions
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be
upgraded simply via a software upgrade box, without the need to change any mechanical parts.
The upgrade box is not included in the package, if you need any further assistance please contact
your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX
signal to save power and will wake immediately when the DMX signal is sent or received again.
Technical Specifications
Power
• Input Voltage: 90~260V AC, 50/60Hz
• Power Consumption: 225W
• Connection: PowerCon in/out
• Fuse: F4A, 250V
Photometric
• Light Source: 180W White LED 7,500K
• Beam Angle: 16°
• Output: 19,120lux @ 2.5M
• PWM: 1,000Hz
• LED Lifespan: 50,000hours
Colour
• 1 colour wheel (7 Colours + Open)
Gobo
• Fixed: 1 x (8 + open) fixed gobo wheel
• Rotating: 1 x (6 + open) interchangeable rotating gobo wheel (outside ø24mm, inside
ø17mm).
Effects
• Prism: 3-facet
• Dimming: 0~100%
• Strobe: 1.2~17Hz
• Focus: 2.5~30m linear via DMX

16
www.event-lighting.com.au
Movement
• 8/16 – bit, auto-reposition
• Pan: 360°/540°/630°
• Tilt: 90°/180°/270°
• Limit mode: Centre/Corner/Edge
Control
• Protocol: DMX512
• DMX Channels: 14/16
• Interface: 3-pin XLR in/out
• Built-in Programming: Yes
• Sound Active: Yes
• Display: 4-button 2.4inch TFT LCD display control panel
Housing
• Materials: Metal & flame retardant ABS
• Finishing: Matte black
• IP rating: IP20
• Cooling: Fan
• Net Weight: 10.5kg
• Rigging: 2pcs omega brackets with 1/4-turn quick locks
WARRANTY
Please refer to your local dealer or contact Event Lighting Pty Ltd.