Event Lighting PRO PAR PAR12X8L User manual

PRO PAR
Model No. PAR12X8L
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

www.event-lighting.com.au
1
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Dimensions

www.event-lighting.com.au
2
Lux Chart
CONTROL BOARD OPERATION
Menu Map
-> - Select DMX address
-> or Select DMX channel mode (CH-1: 4ch / CH-2: 9ch)
-> - Set program speed
-> - Select built-in program
-> Select sound active mode
-> - Select static colour mode
(See static colour mode chart below)
-> - Set strobe speed (Hz)
-> - Set red colour intensity
-> - Set green colour intensity

www.event-lighting.com.au
3
-> - Set blue colour intensity
-> - Set white colour intensity
-> - Set dimmer speed
(nod0: fastest / nod4: slowest)
-> or Toggle LED display on / off
-> Long press “Enter” button to show current temperature
-> Show current software version
-> or Restore settings to factory default
Static colour mode
Value: Function:
C1 Red
C2 Green
C3 Blue
C4 White
C5 Red + White
C6 Green + White
C7 Blue + White
C8 Green + Blue
C9 Red + Blue
C10 Red + Green
C11 Red + Green + Blue
C12 Green + Blue + White
C13 Red + Blue + White
C14 Red + Green + White
C15 Red + Green + Blue + White
DMX Chart
4 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%

www.event-lighting.com.au
4
9 channels Mode
Channel Value Function Note
1 000-255 Master DIMMER 0% ~ 100%
2 000-255 Red: 0% ~ 100%
3 000-255 Green: 0% ~ 100%
4 000-255 Blue: 0% ~ 100%
5 000-255 White: 0% ~ 100%
6 000-012 Strobe OFF
013-255 Strobe (slow-fast)
7
000-009 No Function
010-019 Program 1
020-029 Program 2
030-039 Program 3
040-049 Program 4
050-059 Program 5
060-069 Program 6
070-079 Program 7
080-089 Program 8
090-099 Program 9
100-109 Program 10
110-119 Program 11
120-129 Program 12
130-139 Program 13
140-255 Sound active mode
8 000-255 Speed of auto programs (slow ~ fast) Ch7 must be set between 10-139
9 000-255 Colour fade time (jump ~ fade) Mode must be set to “nod0”
IR Remote
In order to use the IR remote, the fixture must be in DMX
mode without an active DMX connection. If a DMX signal is
received, the fixture will prioritise the DMX signal and ignore
the IR remote.
Use the “On” and “Off” buttons to turn the fixture on or off.
The current IR settings will be saved when the fixture is
powered off and will be automatically reloaded once the
fixture is turned on. To reset to the factory default blackout
mode, long press the “Off” button.
Press the “R”, “G” or “B” buttons to light up the LEDs in red,
green or blue respectively. There is also a selection of preset
colours underneath the “R”, “G” and “B” buttons, known as

www.event-lighting.com.au
5
the D area. Press a colour button in the D area to select that colour.
Use the “X” button to increase the intensity of the selected colour.
Use the “Y” button to decrease the intensity of the selected colour.
Use the “STROBE”, “FADE” or “FLASH” buttons to switch on or off the strobe, fade or step mode.
When a function is selected, the “X” and “Y” buttons will adjust the speed of the effect rather than
the intensity of colours.
Press the “SMOOTH” button, will clear all the remote control setting and fixture will black out.
Technical Specifications
Power
− Input Voltage: 100~240V AC, 50/60 Hz
− Power Consumption: 60W
− Connection: IEC in/out
− Fuse: 5A, 250V
Photometric
− Light Source: 12pcs 4-in-1 RGBW 8W LED
− Beam Angle: 40°
− PWM: 20,000 Hz
− LED Lifespan: 50,000 hours
Effects:
− Dimming: 0~100%
− Strobe: 1~20 Hz
Control
− Protocol: DMX512
− DMX Channels: 4 / 9
− Interface: 3-pin XLR in & out
− Built-in Programming: Yes
− IR Remote Control: Yes
− Display: 4-button & 4-digit LED display control panel
− Cooling: No fan
Housing
− Materials: Die-cast aluminium
− Finishing: Matte black
− IP rating: IP20
− Net Weight: 1.85kg
− Overall Size: 212 x 220 x 62 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.