Event Lighting SURF640 User manual

www.event-lighting.com.au
1
SURF640
6X40W TILT BAR WITH ZOOM
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: 3.0 (06 May 2020)

www.event-lighting.com.au
2
Safety Instructions
Warning
•Do not open this device, there are no user-serviceable parts inside. Risk of electric
shock.
•Do not look at the light source when the device is on.
Caution: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from
adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or
connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water,
or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at
higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing
(anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au
3
Product Installation
•This device can be mounted in many orientations provided each individual device is
secured by the use of correct mounting bracket.
•Use a safety chain when mounting this device overhead.

www.event-lighting.com.au
4
Dimensions
Lux Chart
Lux @ 4°
Distance (m)
1
3
5
8
10
Diameter (m)
Ø 0.06
Ø 0.2
Ø 0.33
Ø 0.55
Ø 0.68
R
11,200
2,450
1,670
790
595
G
16,700
5,300
2,550
1,210
905
B
7,200
2,160
1,070
550
360
W
23,000
7,350
3,550
1,735
1,300
Full
46,000
13,900
8,450
3,980
2,500

www.event-lighting.com.au
5
Lux @ 38°
Distance (m)
1
3
5
8
10
Diameter (m)
Ø 0.7
Ø 2.2
Ø 2.5
Ø 5.6
Ø 6.8
R
2,110
302
114
48
35
G
3,180
459
175
74
54
B
1,310
180
80
13
8
W
4,580
646
244
105
76
Full
9,200
1,268
480
210
148
Menu Operation
Menu – Move up a level.
Up – Move selection up one item.
Down – Move selection down one item.
Enter – Select / Move down a level
Menu
MENU
DESCRIPTION
Function Mode
DMX Address
A001-AXXX
DMX Address setting
DMX Channels
8 CH
8 channel mode
16 CH
16 channel mode
46 CH
46 channel mode
Manual
Preset
Manual mode setting. Straw,
WarmW, White, CoolW, Blue,
Magent, Red, Orange, Yellow,
Green, Teal, Cyan, Blue
Finetune
Finetune the preset (++/--)
Dimmer
0-100
Auto Program
Program 1..8
Wait
Time between 2 colours. 0.1s-
20min
Fade
Fade time between 2 colours. 0.1s-
60s
Dimmer
0-100
Movement
Tilt (0-255)
Tilt between 0°-220°, applied to
Manual & Auto Program
Zoom (0-255)
Zoom between 3.5°-38°, applied to
Manual & Auto Program
Options
Master/Slave
Master/Slave
Off, Master, Slave:1-12
Setting
Lost DMX
Hold/blackout when DMX lost
Tilt Reverse
Reverse tilt (on/off)
Zoom Reverse
Reverse zoom (on/off)

www.event-lighting.com.au
6
Pixel Reverse
Reverse pixel DMX addressing
(on/off)
LCD Reverse
Reverse LCD (on/off). Can also be
changed by pressing the UP and
DOWN buttons simultaneously.
Pixel Frequen
Pixel refresh rate. 1.2K, 2.4K, 3.6K,
4.8K, 6K, 7.2K, 8.4K, 9.6K, 10.8K,
12K, 13.2K, 14,4K, 15.6K, 16.8K,
18K, 19.2K, 20.4K, 21.6K, 22.8K,
24K.
Fan Speed
Auto/Low/High
KeyLock
Enable/Disable keylock. In the
locked state, keys will automatically
lock after 15s of inactivity. Press
and hold MENU for 2s to unlock.
When unlocked, the keys will not
automatically lock
Calibrat
Tilt Movement
If two fixtures are placed on the
same horizontal line and the emitted
light is not on the same horizontal
line, change this value to adjust the
tilt movement.
Zoom Movement
If the angle of the beams emitted by
two fixtures is not the same, change
this value to adjust the beam angle.
LEDs
If the colour temperature of one of
the six LEDs is inconsistent with the
others, change this value to adjust
the colour temperature.
Reset
Reset (no/yes)
Reset to factory settings.
Update
Update (no/yes)
Perform software update.
Info
Temperature
Temperature XX C
Temperature of the LEDs PCB.
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used
to receive instructions from the external controller. For independent control, each fixture must be
assigned its unique address control channels. For example, this device has three channel
modes: 8/16/46, if we set the mode to standard 8 channels mode, and there are several models
that need to be independently controlled, we just simply address first fixture at 1, and second
fixture at 9, third one at 17, etc.
•If the devices have the same address, they will behave synchronically.
•Display is flashing when no DMX signal is received.
8 Channel Mode
Channel
Value
Function

www.event-lighting.com.au
7
1
0-255
Red
2
0-255
Green
3
0-255
Blue
4
0-255
White
5
0-255
Brightness
6
0-7
Shutter Closed (No Light)
Aug-15
No function (Shutter On)
16-119
Strobe effect Slow to Fast
120-127
No function (Shutter On)
128-183
Strobe Random Slow to Fast (All pixels)
184-191
No function (Shutter On)
192-247
Strobe Random Slow to Fast (Random pixels)
248-255
No function (Shutter On)
7
0-255
Tilt
8
0-255
Zoom
16 Channel Mode
Channel
Value
Function
1
0-255
Tilt Coarse
2
0-255
Tilt Fine
3
0-7
Shutter Closed (No Light)
8-15
No function (Shutter On)
16-119
Strobe effect Slow to Fast
120-127
No function (Shutter On)
128-183
Strobe Random Slow to Fast (All pixels)
184-191
No function (Shutter On)
192-247
Strobe Random Slow to Fast (Random pixels)
248-255
No function (Shutter On)
4
0-255
Max Intensity
5
0-255
CTC (Warm white to cold white)
6
0-255
Zoom
7
0-31
Dimmer Curve 1
32-63
Dimmer Curve 2
64-95
Dimmer Curve 3
96-127
Reserved
128-159
Reserved
160-191
Reserved
192-223
Reserved
224-255
Reserved
8
0-255
Tilt Speed Fast to Slow
9
0-15
No Function
16-95
Blackout by Movement Up and Down
96-175
Blackout by Movement Up
176-255
Blackout by Movement Down
10
0-85
Fan Speed (Auto)

www.event-lighting.com.au
8
86-171
Fan Speed (Low)
172-255
Fan Speed (High)
11
0-255
Red
12
0-255
Green
13
0-255
Blue
14
0-255
White
15
0-255
Dim Coarse
16
0-255
Dim Fine
46 Channel Mode
Channel
Value
Function
Applies To
Normal
Reverse
1
0-255
Tilt Coarse
Whole Fixture
2
0-255
Tilt Fine
3
0-7
Shutter Closed (No Light)
8-15
No function (Shutter On)
16-119
Strobe effect Slow to Fast
120-127
No function (Shutter On)
128-183
Strobe Random Slow to Fast (All pixels)
184-191
No function (Shutter On)
192-247
Strobe Random Slow to Fast (Random
pixels)
248-255
No function (Shutter On)
4
0-255
Max Intensity
5
0-255
CTC (Warm white to cold white)
6
0-255
Zoom
7
0-31
Dimmer Curve 1
32-63
Dimmer Curve 2
64-95
Dimmer Curve 3
96-127
Reserved
128-159
Reserved
160-191
Reserved
192-223
Reserved
224-255
Reserved
8
0-255
Tilt Speed Fast to Slow
9
0-15
No Function
16-95
Blackout by Movement Up and Down
96-175
Blackout by Movement Up
176-255
Blackout by Movement Down
10
0-85
Fan Speed (Auto)
86-171
Fan Speed (Low)
172-255
Fan Speed (High)
11
0-255
Red
Pixel 1 Pixel 6
12
0-255
Green

www.event-lighting.com.au
9
13
0-255
Blue
14
0-255
White
15
0-255
Dim Coarse
16
0-255
Dim Fine
17
0-255
Red
Pixel 2 Pixel 5
18
0-255
Green
19
0-255
Blue
20
0-255
White
21
0-255
Dim Coarse
22
0-255
Dim Fine
23
0-255
Red
Pixel 3 Pixel 4
24
0-255
Green
25
0-255
Blue
26
0-255
White
27
0-255
Dim Coarse
28
0-255
Dim Fine
29
0-255
Red
Pixel 4 Pixel 3
30
0-255
Green
31
0-255
Blue
32
0-255
White
33
0-255
Dim Coarse
34
0-255
Dim Fine
35
0-255
Red
Pixel 5 Pixel 2
36
0-255
Green
37
0-255
Blue
38
0-255
White
39
0-255
Dim Coarse
40
0-255
Dim Fine
41
0-255
Red
Pixel 6 Pixel 1
42
0-255
Green
43
0-255
Blue
44
0-255
White
45
0-255
Dim Coarse
46
0-255
Dim Fine

www.event-lighting.com.au
10
More Functions
•Remote Device Management (RDM) which allows users to remotely control the device.
Users can use RDM to remotely change the DMX address and the DMX settings. Each
device has a unique RDM code programmed during manufacture to facilitate this
function. It is not recommended for users to change this code.
•Software upgrade function via DMX cable. If there is any new firmware for this device, it
can be upgraded simply via a software upgrade box, without the need to change any
mechanical parts. The upgrade box is not included in the package, if you need any
further assistance please contact your authorized dealer.
•Software upgrade can also be performed by connecting to another fixture by following
these steps. This will update the software on Fixture A:
oOn Fixture A, go to Menu > Update > Y > Start.
oConnect Fixture A to Fixture B with a DMX cable.
oPower on Fixture B.
oWhen the LCD displays “Waiting for file”, press Enter on Fixture A.
oUpgrade will be complete. Press Menu to return to the Main Menu.
•Hibernation. The device will enter sleep mode if activated after a period of disconnecting
DMX signal to save power and will wake immediately when the DMX signal is sent or
received again.
Technical Specifications
Power
•Input Voltages: 100V~240V AC, 50/60Hz
•Power Consumption: 300W
•Power Connection: Neutrik Powercon TRUE1 in/out
•Power Linking: 2 units at 110V, 6 units at 240V
•Fuse: T6.3A, 250V
Photometrics
•Light Source: 6 pcs 40W RGBW LEDs
•Beam Angle: 4° to 38°
•Field Angle 10° to 42°
•Output: 1,268 lux @ 3m @ 38°
•PWM: 1,200 - 24,000 Hz
Effects
•Dimming: 0-100%
•Strobe: 1.2 - 24 Hz
Control
•Operational Modes: DMX512, Master / Slave, Sound Active, Manual
•RDM: Change DMX mode, change DMX address.
•Display: Reversible LCD Display
•DMX Protocol: DMX512
•DMX Channel Mode: 8 / 16 / 46 (Normal) / 46 (Reverse)

www.event-lighting.com.au
11
•DMX Interface: 3- or 5-pin XLR in/out
Housing
•Housing Materials: Die-cast Aluminium and Iron Housing
•Housing finish: Matte Black
•Cooling: 4-fan cooling system
•Overall size: 498 x 193 x 304 mm
•Net Weight: 11.5 kg
•Rigging: 2x Omega brackets with ¼ turn quick locks
•Optional Roadcase: SURF640RC
Warranty
Please refer to your local dealer or contact Event Lighting Pty Ltd.