Event Lighting M7W40RGBW User manual

1
WASH MOVING HEAD
M7W40RGBW
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

3
Product appearance, LUX chart, Dimensions
1. Project lens
2. Head
3. Arm
4. Base
5. Display
6. Foot stand
7. Operation button
8. Handel
9. Wireless indicator
10. Mic
11. Left button
12. Battery indicator
13. Up button
14. Down button
15. Enter button
16. Right button
17. Ethernet out
18. 5-pin DMX in
19. Ethernet in
20. 5-pin DMX out
21. Powercon in
22. Powercon out
23. Fuse

4

5
Menu operation
Description of icons in the menu
CONNECT LIGHT INFOMATION SET PROGRAM
Menu
Default setting shadowed. Mark with ①can be basic reloaded, ② be program reloaded, ③can be private reloaded.
CONNECT
DMX Address① XXX DMX address setting
Wireless① (Wireless Module) Wireless Enabled
Artnet① (Artnet Module) Artnet Enabled
LIGHT
Max Temperature① 80~139
℃
/ 176~282
℉
Lamp will switch off when
temperature continuously over max
temperature for 2 minutes
Lamp Adjust① PAN… Adjust value of channel
INFORMATION
Time Info. Current XXXX(Hours)
Fixture Life XXXX(Hours)
Lamp Life XXXX(Hours)
Fixture boot time
Fixture total run time
Total lamp run time
Temperature Near Lamp Temp (depends on fixture) Temperature Sensors
Fans Speed Near Lamp Fan (depends on fixture) Fan speed Sensors
Channel Value Display value of channel
Error Message Error channels
Fixture Model M7W40RGBW Display brand and model
Software Ver 1U01 V1.0.00 Version of each IC
SET
Reset All
Pan&Tilt
:
Reset all
Reset Pan&Tilt
:
Movement Pan Reverse①
Tilt Reverse①
Pan Degree①
Encoders①
Pan/Tilt Mode①
ON/OFF
ON/OFF
630°/540°
ON/OFF
Stand/Smooth
Pan Reverse
Tilt Reverse
Choose Pan Degree
Encoder wheel on/off
Choose pan/tilt mode
UI Set Mic Sens. ③
No Signal①
Temperature. C/F①
Fans Mode①
Hibernation①
Backlight①
Flip Display①
Display Bright③
Brand Show①
Key Lock①
Language①
0~99%,60%
Close/Hold/Auto/Music
Fahrenheit/Celsius
Auto Speed/High Speed
OFF, 01M~99M，15M
02~60m 02m
ON/OFF
00~31 10
ON/OFF
ON/OFF
En/Fr/Sp/简/繁
Sensitivity of Mic
Mode when no signal
Temperature at ℃/℉
Fans mode
Sleeping mode
Show backlight time
Display 180°reverse
Display Brightness
Show brand or not
Key lock on/off
Language Select
Fixture Set Theater Mode ON/OFF Theater Mode

6
Users User Mode① Standard
Extended
Basic-8bit
Basic-16bit
User
Standard mode (22 Ch)
Extended mode (51 Ch)
Basic mode-8bit (19 Ch)
Basic mode-16bit (21 Ch)
User program mode
Edit User③ Max Channel = XX
PAN = CH01
:
Edit users mode
Calibration③ -Password-
Color
:
=XXX
=XXX
:
Password: 050
Calibrate channel value
Fixture ID③ Name
-Password-
PID Code
Name
Password: 050
Set PID of RDM
Wireless Set①
(Wireless Module)
DMX On Cable
Reset Connect
ON/OFF
ON/OFF
DMX Send Out
Reset Connect
Ethernet Set③ IP Address
IP Mask
Universe
DMX on Cable
2.X.X.X
255.0.0.0
0
ON/OFF
Ethernet Set
Reload Default Basic Reload(①)
Program Reload(②)
---Password---
Private Reload(③)
All Reload
Update Fixture
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
ON/OFF
Basic Reload
Program Reload
Password: 050
Private Reload
All Reload
Software Upgarde
PROGRAM
Play① DMX Receive
Slave Receive
Sequence
Music
Slave Receive 1,2,3
Master / Alone
Master / Alone
DMX Receive
Choose Slave Position
Run Sequence
Sound Active Mode
Select Chase② Chase Part 1
Chase Part 2
Chase Part 3
Chase 1 ~ 8 Chase 1
Chase 1 ~ 8 Chase 2
Chase 1 ~ 8 Chase 3
Select and run auto program
Edit Chase② Chase 1
:
:
Chase 8
Chase Test
Step 01
:
Step 64
=SCxxx
:
=SCxxx
Test
Beginning scene
:
Ending scene
Edit Scenes② Edit Scene 001
~ Edit Scene 250
Pan,Tilt,……
Fade Time--
Secne Time--
DMX Input
=xxx
=xxx
=xxx
Input manual scene
Modify manually fading time
Modify manually scene time
Input scene from exterior controller
Scenes Record ScXX=>ScXX Auto Input scenes
Reload explanation:
“Basic Reload” will reload all function marked with ①
“Program Reload” will reload all function marked with ②
“Private Reload” will reload all function marked with ③
“All Reload” reload functions marked with ①②③

7
DMX Chart
Channel name function Min
DMX
Max
DMX
St Ex Ba1 Ba2
1 1 1 1 Pan Pan Coarse 0 255
2
2
2 Pan fine Pan Fine 0 255
3 3 2 3 Tilt Tilt Coarse 0 255
4
4
4 Tilt fine Tilt Fine 0 255
5 5 3 5 Movement
Speed fastest to Slowest 0 255
6
Movement
Function
Normal 0 15
Movement With Blackout 16 31
TBD 32 255
6 7
Shutter
Function
Normal Shutter Functions 0 15
Pulse-effect Forward 16 31
Pulse-effect Reverse 32 47
Random Strobe 48 63
TBD 64 255
7 8
Shutter
Normal Shutter Functions
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Forward
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Pulse-effect Reverse
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
Random Strobe
Close 0 31
Strobe Rate (slow to fast) 32 223
Open 224 255
4 6 Shutter
Shutter closed 0 31
No function (shutter open) 32 63
Strobe effect slow to fast 64 95
No function (shutter open) 96 127
Pulse-effect in sequences 128 159
No function (shutter open) 160 191
Random strobe effect slow to fast 192 223
No function (shutter open) 224 255
8 9 5 7 Dimmer Dimmer (0->100%) 0 255

8
9 10 6 8
Virtual
Color
Function
On Function 0 15
CTC Function 16 31
Forward Spin 32 47
Reverse Spin 48 63
Continuous 64 79
Color Bounce 80 111
TBD 112 255
10 11 7 9 Virtual
Color1
CTC Function
Colour Temperature Correction
2000K->2700K 0 223
White 3200K 224 231
White 4200K 232 239
White 5600K 240 247
White 8000K 248 255
Forward Spin
Rainbow Effect (Slow->Fast) 0 255
Reverse Spin
Rainbow Effect (Slow->Fast) 0 255
Continuous & Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
White 4 4
Red=0, Green->up, Blue=full, White=0 5 46
Red=0, Green=full, Blue-> down, White=0 47 88
Red->up, Green=full, Blue=0,White=0 89 130
Red=full, Green->down, Blue=0,White=0 131 172
Red=full, Green=0,Blue->up, White=0 173 214
Red->down, Green=0,Blue=full, White=0 215 255
11 12 8 10
Virtual
Color2
(Only On
Color
Bounce)
Color Bounce
Black 0 0
Red 1 1
Green 2 2
Blue 3 3
White 4 4
Red=0, Green->up, Blue=full, White=0 5 46
Red=0, Green=full, Blue->down, White=0 47 88
Red->up, Green=full, Blue=0,White=0 89 130
Red=full, Green->down, Blue=0,White=0 131 172
Red=full, Green=0, Blue->up, White=0 173 214
Red->down, Green=0, Blue=full, White=0 215 255
12 13 9 11 Red-All Red 0->100% 0 255
13 14 10 12 Green-All Green 0->100% 0 255
14 15 11 13 Blue-All Blue 0->100% 0 255

9
15 16 12 14 White-All White 0->100% 0 255
16 17 13 15 Zoom 36°-> 4° 0 255
17 18 14 16 Foreground No Function 0 15
Foreground Color 16 255
18 19 15 17 Background No Function 0 15
Background color 16 255
19 20 16 18 Pattern
On Pattern 0 15
Pattern control 16 31
Pattern Effect 1~14 32 255
20 21 17 19 Pattern
Speed
Pattern control
Picture Effect 1-250 3 252
Pattern Effect
Slow-> Fast 0 255
21 22 18 20 Master
Dimmer Fade 0->100% 0 255
23 Red 1 Red 0->100% 0 255
24 Green 1 Green 0->100% 0 255
25 Blue 1 Blue 0->100% 0 255
26 White 1 White 0->100% 0 255
: : : : :
47 Red 7 Red 0->100% 0 255
48 Green 7 Green 0->100% 0 255
49 Blue 7 Blue 0->100% 0 255
50 White 7 White 0->100% 0 255
22 51 19 21 Control
Normal 0 7
Reset All 8 15
Pan & Tilt Reset 16 23
TBD 24 47
Other Reset 48 55
Display Off 56 63
Display On 64 71
TBD 72 79
TBD 80 87
Hibernation 88 95
TBD 96 255
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions
from the external controller. For independent control, each fixture must be assigned its unique address control channels.
For example, this device has four channel modes: 22/51/19/21, if we set the mode at standard 22 channels mode, and
there are several models need to be independently controlled, we just simply address first fixture at 1, and second
fixture at 23, third one at 45, etc.
If the devices have the same address, they will behave synchronically.
Display is flashing when no DMX signal is received.

10
More functions
- RDM. RDM stands for “Remote Device Management”, with this function, users can realize remote control of the
device, such as remotely changing DMX address, reverse pan/tilt setting, check a lot of useful information such as
temperature, power consumption, fan speed. Etc. Every single device has a unique RDM code programmed at
manufacture to distinguish from each other. It is not recommended for users to change this code.
- Software upgrade via DMX cable. If there is any new firmware for this device, it can be upgraded simply via a
software upgrade box, no need to change any mechanical parts. The upgrade box is not included in the package, if
need any further assistance please just contact your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX signal to save the
power consumption, and will return immediately as soon as the DMX signal is sent again.
- Display back-up communication IC. There is a back-up communication IC installed in the display PCB, so users
could replace at once if the original one is broken.
- Display flip. By press up and down button for more than 3 seconds, the display will flip automatically, this function is
useful to read menu conveniently when device is hanged.

11
Technical Specifications
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Consumption: 265W
Connection: Neutrik® Powercon – In / Out
Fuse: T3.15A, 250V
Photometric
Light Source: 7 pcs Osram® 40W RGBW LED
Beam Angle: 4° - 36°
Output: 7000lumen 43000lux @ 3M RGBW at 4°
PWM: 1200Hz
LED Lifespan: 60,000 hours
Effects
Dimming: 0 ~ 100%
Pixel Dimming: Yes
Strobe: 0.5 ~26 Hz
Zoom: 4° - 36°
Movement 8 / 16 – bit
Pan: 630° (1.56 sec) / 540° (1.3 sec)
Tilt: 265° (0.85 sec)
Control
Protocol: DMX512 (W-DMX™ Optional)
DMX Channels: 22/51/19/21
Interface: 5-pin XLR / Artnet interfaces
RDM: Yes
Software Upgrade via DMX: Yes
Built-in Programming: Yes
Sound Active: Yes
Display: 2.4″ Colour LCD with battery
Cooling: Multi Sensor Thermostat Controlled Variable Speed Fan
MISC
Road Case: Optional
Rigging: 2pcs Omega Brackets with 1/4-turn Quick Locks
Housing
Materials: ABS & Steel
Finishing: Matte black
IP rating: IP20
Net Weight: 12 kg
Overall Size: 324 x 250 x 456 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.