Event Lighting PIXBAR6x12 User manual

PIXBAR6x12
6x 12W RGBWAU Pixel Control Bar
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: 3.2.0 (7 Oct 2020)

www.event-lighting.com.au
2
Contents
Safety Instructions
Product Installation
Diagrams
Control Board Operation
Special Chase Mode
DMX Chart
Technical Specifications
Warranty

www.event-lighting.com.au
3
Safety Instructions
Warning
• Do not open this device, there are no user-serviceable parts inside.
• Do not look at the light source when the device is on.
• This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inches (50 cm) from
adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or
connected to power.
• Do not operate this device outdoors or in any location where dust, excessive heat, water,
or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at
higher temperatures.
Power Input and Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz. Link up to the maximum of 8A. DO NOT exceed this amount.
Product Installation
• This device can be mounted in many orientations provided each individual device is
secured by the use of correct mounting bracket.
• Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine wire fuse of the device fuses, replace it with a fuse of the same type and rating. Before
replacing the fuse, unplug the mains lead. Procedure:
• Unscrew the fuse holder on the rear panel.
• Remove the old fuse from the fuse holder.
• Install the new fuse into the fuse holder.
• Replace the fuse holder in the housing and securely fix it.

www.event-lighting.com.au
4
Dimensions
Lux Chart
LUX @ 30°
1m
2m
3m
4m
5m
R
783
231
104
63
48
G
992
305
137
82
60
B
950
292
132
80
58
W
1352
422
189
115
81
A
482
157
73
47
35
UV
251
76
34
21
15
Full
4000
1280
575
347
235
LUX @ 55°
1m
2m
3m
4m
5m
R
435
130
59
37
28
G
551
171
78
48
35
B
502
155
75
46
33
W
752
235
110
65
46
A
268
100
42
27
20
UV
84
26
12
7
5
Full
2230
713
320
196
132
Menu Operation
1. Menu – Move up a level.
2. Up – Move selection up one item.
3. Down – Move selection down one item.
4. Enter – Select / Move down a level.

www.event-lighting.com.au
5
Control Panel Operation
Display
Options/Values
Description
01. DMX Address
<001> - <512>
Set the DMX address.
02. DMX Channel
<03> <04> <06> <08> <12>
<36> <38>
Set the DMX channel mode.
03. Dimmer Curve
<01> <02> <03> <04>
Set the dimmer curve.
04. Static Colour
R, G, B, W, A, U, GB, RG, …,
RGBWAU
Set a static colour.
05. Manual Colour
R<000> - <255>
G<000> - <255>
B<000> - <255>
W<000> - <255>
A<000> - <255>
U<000> - <255>
S<000> - <230>
Set the intensity of each colour
separately, and the strobe rate.
06. Manual WCT
WCT: <01> – <11>
DIM: <001> – <100>
Set the colour temperature WCT 01-
11 and adjust the brightness
07. Auto Program
<Pr: 01> – <Pr: 19>
<Sp: 000> – <Sp: 100>
<Dim: 000> – <Dim: 255>
Select an auto program, speed and
brightness.
08. Sound Mode
Sen: <000> – Sen:<100>
Select sound active mode and
sensitivity level.
09. Master/Slave
<M> <S>
Select master or slave mode.
10. Factory Set
<No> <Yes>
Reset to factory settings.
DMX Address
After selecting DMX Address, press Enter and use Up or Down to set the desired DMX address
then press Enter to confirm.
DMX Modes
After selecting DMX Channel, press Enter and use Up or Down to select the desired DMX
channel mode. Press Enter to confirm.
Dimming Mode
After selecting Dimmer Curve, press Enter and use Up or Down to select the desired dimming
mode, then press enter to confirm your selection.
Selecting Static Colours
After selecting Static Colour, use Up or Down to select the desired solid colour.
Value:
Function:
Static colour <R>
Red
Static colour <G>
Green
Static colour <B>
Blue
Static colour <W>
White
Static colour <A>
Amber
Static colour <U>
UV
Static colour <GB>
Green+Blue
Static colour <RG>
Red+Green
Static colour <RB>
Red+Blue
Static colour <RW>
Red+White
Static colour <GW>
Green+White

www.event-lighting.com.au
6
Static colour <BW>
Blue+White
Static colour <WA>
White+Amber
Static colour <RA>
Red+Amber
Static colour <GA>
Green+Amber
Static colour <BA>
Blue+Amber
Static colour <RGB>
Red+Green+Blue
Static colour <RGW>
Red+Green+White
Static colour <GBW>
Green+Blue+White
Static colour <GBA>
Green+Blue+Amber
Static colour <BWA>
Blue+White+Amber
Static colour <RGA>
Red+Green+Amber
Static colour <GWA>
Green+White+Amber
Static colour <RWA>
Red+White+Amber
Static colour <RGBA>
Red+Green+Blue+Amber
Static colour <GBWA>
Green+Blue+White+Amber
Static colour <RGBW>
Red+Green+Blue+White
Static colour <RBWA>
Red+Blue+White+Amber
Static colour <RGWA>
Red+Green+White+Amber
Static colour <RGBWA>
Red+Green+Blue+White+Amber
Static colour <RU>
Red + Green
Static colour <GU>
Red + Green + Blue
Static colour <AU>
Red + White
Static colour <RAU>
Green + White
Static colour
<RGBWAU>
Red + Green + Blue + White + Amber + UV
Manual Colour
This allows you to manually set the intensity of R, G, B, W, A and UV channels separately, as
well at set the strobe speed, without a DMX controller.
Use Up or Down to select R/G/B/W/A/UV to adjust colour intensity or S to adjust strobe speed,
then use Up or Down to set colour intensity values between 0 and 255 or strobe speed between
0 (slowest) and 100 (fastest). Press Enter to confirm.
Manual WCT
Select the colour temperature to be changed from <WT01> - <WT11> then use Up or Down to
select intensity between 1 – 100
Automatic Mode
PR01
4 colours switching
PR02
36 colours switching
PR03
6 colours fading (slow in slow out)
PR04
36 colours fading (slow in slow out)
PR05
6 colours fading (slow in fast out)
PR06
36 colours fading (slow in fast out)
PR07
6 colours fading (fast in slow out)
PR08
36 colours fading (fast in slow out)
PR09
Colour macros
PR10
Auto chasing 1
PR11
Auto chasing 2
PR12
Auto chasing 3
PR13
Auto chasing 4

www.event-lighting.com.au
7
PR14
Auto chasing 5
PR15
Auto chasing 6
PR16
Auto chasing 7
PR17
Auto chasing 8
PR18
Auto chasing 9
PR19
Multi fixture chasing
Set Auto Run PR01 – PR18
Enter "Auto Program" mode, use “Up” and “Down” button to select the built-in programs. Press
“Enter" and use “Up” and “Down” button to select auto run speed from <Sp000> to <Sp100>.
Press “Enter" and use “Up” and “Down” button to select dimmer of “Auto Program” from
<dim000> – <dim255>. Press “Enter" to save new setting.
Set Multi Fixture Chases PR19
Before starting, go to each fixture and reset the menu to factory defaults.
1. On the master unit, setup the DMX address to the total number of fixtures in the string.
For example, if you have a total of 20 PIXBARs including the master, set the DMX
address to 20.
2. On the master unit, go to Master/Slave menu setting and set it to Master.
3. On the master unit, set the unit to Auto Mode PR19.
4. On each slave unit, set the DMX address to the position of the fixture in the string. For
example, if the unit is the 2nd unit in the string, including the master, set the DMX address
to 2. It is possible to double up fixture positions.
5. On each slave unit, go to Master/Slave menu setting and set it to Slave.
Sound Mode
After selecting Sound Mode, use Up and Down to set the sound sensitivity Sen 000 – Sen 100,
press Enter to confirm.
Master/Slave Operation
1. Set the master fixture to one of the standalone operating modes: Auto, Sound, Static
colour, or manual colour.
2. Set the slave fixtures to Slave mode and press Enter.
Factory Set
To restore factory settings, select Factory Set and press Enter, then use Up and Down to select
Yes. Press Enter to confirm.

www.event-lighting.com.au
8
DMX Chart
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used
to receive instructions from the external controller. For independent control, each fixture must be
assigned its unique address control channels. For example, this device has seven channel
modes: 3/4/6/8/12/36/38, if we set the mode to 3 channel mode, and there are several models
that need to be independently controlled, we just simply address first fixture at 1, and second
fixture at 4, third one at 7, etc.
• If the devices have the same address, they will behave synchronically.
• Display is flashing when no DMX signal is received.
Channel
Value
Function
3
Ch
4
Ch
6
Ch
8
Ch
12
Ch
36
Ch
38
Ch
1
1
1
1
1
0-255
Red: 0 - 100%
2
2
2
2
2
0-255
Green: 0 - 100%
3
3
3
3
3
0-255
Blue: 0 - 100%
4
4
4
4
0-255
White: 0 - 100%
5
5
5
0-255
Amber: 0 - 100%
6
6
6
0-255
UV: 0 - 100%
7
7
0-255
Master Dimmer 0 - 100%
8
8
0-9
No Function
10-255
Strobe, slow to fast (1-30Hz)
9
0-9
No Function
10-31
Colour Temperature 1 (warmest)
32-54
Colour Temperature 2
55-77
Colour Temperature 3
78-100
Colour Temperature 4
101-123
Colour Temperature 5
124-146
Colour Temperature 6
147-169
Colour Temperature 7
170-192
Colour Temperature 8
193-215
Colour Temperature 9
216-238
Colour Temperature 10
239-255
Colour Temperature 11 (coolest)
10
0-9
No Function
10-21
RGBWAU colours switching
22-34
36 colours switching
35-47
RGBWAU colours fading (slow in slow out)
48-60
36 colours fading (slow in slow out)
61-73
RGBWAU colours fading (slow in fast out)
74-86
36 colours fading (slow in fast out)
87-99
RGBWAU colours fading (fast in slow out)
100-112
36 colours fading (fast in slow out)
113-125
Colour Macros
126-138
Auto chase 1 (Auto Pr10)
139-151
Auto chase 2 (Auto Pr11)
152-164
Auto chase 3 (Auto Pr12)

www.event-lighting.com.au
9
165-177
Auto chase 4 (Auto Pr13)
178-190
Auto chase 5 (Auto Pr14)
191-203
Auto chase 6 (Auto Pr15)
204-216
Auto chase 7 (Auto Pr16)
217-229
Auto chase 8 (Auto Pr17)
230-242
Auto chase 9 (Loop Auto Pr10-Pr17)
243-255
Sound Active
11
0-255
Speed of Auto Programs (slow to fast)
12
0-9
Use the dimmer control board setting
10-70
Dimmer curve 1
71-132
Dimmer curve 2
133-194
Dimmer curve 3
195-255
Dimmer curve 4
1
1
0-255
LED 1 Red 0-100%
2
2
0-255
LED 1 Green 0-100%
3
3
0-255
LED 1 Blue 0-100%
4
4
0-255
LED 1 White 0-100%
5
5
0-255
LED 1 Amber 0-100%
6
6
0-255
LED 1 UV 0-100%
7
7
0-255
LED 2 Red 0-100%
8
8
0-255
LED 2 Green 0-100%
9
9
0-255
LED 2 Blue 0-100%
10
10
0-255
LED 2 White 0-100%
11
11
0-255
LED 2 Amber 0-100%
12
12
0-255
LED 2 UV 0-100%
13
13
0-255
LED 3 Red 0-100%
14
14
0-255
LED 3 Green 0-100%
15
15
0-255
LED 3 Blue 0-100%
16
16
0-255
LED 3 White 0-100%
17
17
0-255
LED 3 Amber 0-100%
18
18
0-255
LED 3 UV 0-100%
19
19
0-255
LED 4 Red 0-100%
20
20
0-255
LED 4 Green 0-100%
21
21
0-255
LED 4 Blue 0-100%
22
22
0-255
LED 4 White 0-100%
23
23
0-255
LED 4 Amber 0-100%
24
24
0-255
LED 4 UV 0-100%
25
25
0-255
LED 5 Red 0-100%
26
26
0-255
LED 5 Green 0-100%
27
27
0-255
LED 5 Blue 0-100%
28
28
0-255
LED 5 White 0-100%
29
29
0-255
LED 5 Amber 0-100%
30
30
0-255
LED 5 UV 0-100%
31
31
0-255
LED 6 Red 0-100%
32
32
0-255
LED 6 Green 0-100%

www.event-lighting.com.au
10
33
33
0-255
LED 6 Blue 0-100%
34
34
0-255
LED 6 White 0-100%
35
35
0-255
LED 6 Amber 0-100%
36
36
0-255
LED 6 UV 0-100%
37
0-255
Master Dimmer 0 - 100%
38
0-9
No Function
10-255
Strobe, slow to fast (1-30Hz)
Technical Specifications
Power
• Input Voltages: 100V~240V AC,50/60Hz
• Power Consumption: 60W
• Power Connection: Neutrik® Powercon Input & Output Connection
Photometrics
• Light Source: 6pcs 12W RGBWAU 6-in-1 LEDs
• Beam Angle: 30° (Optional 55°)
• Output: 1,280 lux @2.0 M RGBWAU full on
• PWM: 12,000 Hz
• LED Life: 50,000 hours
Effects
• Dimming: 4 Dimming Curves
• Strobe: 1 - 30 Hz
Control
• Operational Modes: DMX, Auto, Manual, Sound Active, Master/Slave
• DMX Protocol: DMX512
• DMX Channel Mode: 3 / 4 / 6 / 8 / 12 / 36 / 38
• DMX Interface: 3-Pin (Optional 5-Pin XLR)
• Display: 4-button LCD Display Control Panel
• Software Upgrade via DMX: Yes
Housing
• Housing Materials: Aluminium Housing
• Housing finish: Matte Black
• Cooling: Fanless Cooling
• Dimension: 568 x 165 x 80 mm
• Net Weight: 2.6 kg
Warranty
Please refer to your local dealer or contact Event Lighting Pty Ltd.