Event Lighting ORBIT2 User manual

www.event-lighting.com.au
1
ORBIT2
3-in-1 Effect Light
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: 10 (6 May 2020)

www.event-lighting.com.au
2
Safety Instructions
Warning
• Do not open this device, there are no user-serviceable parts inside. The laser power
inside the housing can start fires or burn skin and will cause eye injury.
• Do not look at the light source when the device is on.
• This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from
adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or
connected to power.
• Do not operate this device outdoors or in any location where dust, excessive heat, water,
or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at
higher temperatures.
• Do not leave the product running unattended. Use the key to lock the laser to avoid
unauthorised use.
• Use aperture cover when the laser is not in use.
Laser Warning
Laser light can cause instant eye injury if the product is not set up and used correctly.
Avoid direct eye contact with the laser light. Never intentionally expose your eyes or others to
direct laser light. This laser product can potentially cause instant eye damage or blindness if
laser light directly strikes the eyes. The heat from a laser cannot be felt, but it can still injure or
blind people. This can occur even with very small amounts of exposure at a long distance.
This product contains a Class 3B Laser. It is critical to prevent the possibility of ANY direct eye
exposure.
• Do not operate the laser without reading and understanding the safety information
contained in this manual.
• Do not assume exposure to an individual laser beam is safe.
• Do not assume a moving laser light is safe. Eye injury can occur instantly.

www.event-lighting.com.au
3
• ORBIT2 must be installed at least 3 metres above ground level and at least 3 metres
horizontally from any person. See the Product Installation section for details.
• Do not point the laser at any person or animal.
• Do not point the laser towards any area where people could be exposed to it.
• Do not point the laser towards any reflective surfaces, such as windows, mirrors and
metals. Laser reflections can also cause injury.
• Do not point the laser towards any area where you or the operator do not know where it
is being directed.
• Do not point the laser into the sky or towards any aircraft.
• The legal requirements for operating laser products vary between jurisdictions. It is the
user’s responsibility to meet the legal requirements in the location/country of use.
Additional laser warning stickers (pictured above) are included with this user manual. Please
attach these to the power supply.
Power Input
This device has an auto-switching power supply work with input voltage range of 100~240 VAC,
50/60 Hz.
Product Installation
• This device can be mounted in many orientations provided each individual device is
secured by the use of correct mounting bracket.
• This device should be directed above the heads of people. Do not direct this device
towards the line of sight of anyone.
o Refer to the diagram below.
• A minimum of 3 meters vertical separation is required between the floor and the laser
device.
• A minimum of 3 metres horizontal separation is required between the laser light and any
person or public space.
• Use a safety chain when mounting this device overhead.

www.event-lighting.com.au
4
Laser Interlock
The use of the laser is controlled by an interlock and key located on the back of the unit. In order
for the laser to operate, the interlock must be inserted, and the key switched to the unlocked
position.
• If these conditions are not met, only the LEDs will be operational.
Overview
Dimensions

www.event-lighting.com.au
5
Menu Operation
1. Menu – Move up a level.
2. Up – Move selection up one item.
3. Down – Move selection down one item.
4. Enter – Select / Move down a level.
5. DMX Signal LED indicator. LED will flash when
DMX connected.
6. Master/Slave mode indicator. LED will flash when
in Slave mode.
Menu
Display
Function
Description
Addr
DMX Address
Change DMX Address (A001-
A512).
ChNd
DMX Channels
Change DMX Channel Mode
(2Ch / 11Ch).
SLNd
Master/Slave Mode
Change between Master
(NASt) and Slave (SL1/SL2)
mode.
In Slave Mode 1 (SL1), slave
fixtures will follow the Master
fixture when in Sound Active
Mode.
In Slave Mode 2 (SL2), each
slave fixture will use its own
microphone and behave
independently when in Sound
Active Mode.
When not in Sound Active
Mode, SL1 and SL2 function
identically.
Soun
Sound Mode and Sound
Sensitivity
Change between Sound
Active Modes (So0-So8) and
Sound Sensitivity (Se00-
Se99)
Auto
Auto-run Mode
Change between Auto-run
Modes (Aut0-Aut8) and Auto-
run Speed (SP1-SP9)
Led
Display backlight
Turn the display backlight on
or off.
diSP
Display normal/inverted.
Switch between normal or
inverted display mode.
Ver
Software Version
Display the current software
version.

www.event-lighting.com.au
6
IR Remote
Button
Description
Black Out
Turn on/off
Auto
Autoplay
Sound
Sound Active mode
Strobe
Strobe mode
Fade/ Jump
No Function
Sensitivity
Adjust sound sensitivity
R/G/B/W/A/UV/W
No Function
+
Increase parameter (strobe
speed, sound sensitivity, auto
speed)
-
Decrease parameter (strobe
speed, sound sensitivity, auto
speed)
0-8
Switch between functions in
Auto Mode and Sound Active
Mode
9
No Function
DMX Chart
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used
to receive instructions from the external controller. For independent control, each fixture must be
assigned its unique address control channels. For example, this device has three channel
modes: 2/11, if we set the mode to standard 2 channels mode, and there are several models that
need to be independently controlled, we just simply address first fixture at 1, and second fixture
at 3, third one at 5, etc.
• If the devices have the same address, they will behave synchronically.
• Display is flashing when no DMX signal is received.

www.event-lighting.com.au
7
2 Channel Mode
Channel
Value
Function
1
5-20
Auto 0 (combined effect)
21-35
Auto 1 (Derby effect 1)
36-50
Auto 2 (Derby effect 2)
51-65
Auto 3 (Laser + strobe)
66-80
Auto 4 (Derby + strobe)
81-95
Auto 5 (Laser + Derby 1)
96-110
Auto 6 (Laser + Derby 2)
111-125
Auto 7 (Laser effect)
126-130
Auto 8 (Strobe effect)
131-144
Sound 0 (Combined effect)
145-159
Sound 1 (Derby effect 1)
160-174
Sound 2 (Derby effect 2)
175-189
Sound 3 (Laser + strobe)
190-204
Sound 4 (Derby + strobe)
205-219
Sound 5 (Laser + Derby 1)
220-234
Sound 6 (Laser + Derby 2)
235-249
Sound 7 (Laser effect)
250-255
Sound 8 (Strobe effect)
2
0-255
Run speed and sound sensitivity adjust

www.event-lighting.com.au
8
11 Channel Mode
Channel
Value
Description
Function
1
0-13
Derby 1
None
14-27
Red
28-41
Green
42-55
Blue
56-69
White
70-83
Red + Green
84-97
Red + Blue
98-111
Red + White
112-125
Green + Blue
126-139
Green + White
140-153
Blue + White
154-167
Red + Green + Blue
168-181
Red + Green + White
182-195
Red + Blue + White
196-209
Green + Blue + White
210-223
Red + Green + Blue + White
224-237
Jump change with Derby effect 1
238-255
Jump change with Derby effect 2
2
0-250
Derby 1 Strobe Effect
Speed from slow to fast
251-255
Sound strobe
3
0-13
Derby 2
None
14-27
Red
28-41
Green
42-55
Blue
56-69
White
70-83
Red + Green
84-97
Red + Blue
98-111
Red + White
112-125
Green + Blue
126-139
Green + White
140-153
Blue + White
154-167
Red + Green + Blue
168-181
Red + Green + White
182-195
Red + Blue + White
196-209
Green + Blue + White
210-223
Red + Green + Blue + White
224-237
Jump change with Derby effect 1
238-255
Jump change with Derby effect 2
4
0-250
Derby 2 Strobe Effect
Speed from slow to fast
251-255
Sound strobe
5
0-7
Laser effect
None
8-47
Red
48-87
Green
88-127
Red + Green
128-167
Red + Green Strobe
168-207
Green + Red strobe
208-255
Alternate strobe

www.event-lighting.com.au
9
6
0-250
Laser Strobe effect
Speed from slow to fast
251-255
Sound activated
7
0-7
Laser rotation
No rotation
8-87
Backwards rotation, slow to fast
88-167
Forwards rotation, fast to slow
168-255
Random rotation
8
0-7
Strobe mode
(centre, can add
effects on top)
No function
8-36
No Strobe
37-66
Strobe effect 1
67-96
Strobe effect 2
97-126
Strobe effect 3
127-156
Strobe effect 4
157-186
Strobe effect 5
187-216
Strobe effect 6
217-246
Strobe effect 7
246-255
Strobe effect 8
9
0-255
Strobe effect speed
Ch. 8 effect speed, slow to fast
10
0-7
Strobe effect
No Strobe
8-240
Strobe speed, slow to fast
241-255
Sound activated
11
0-9
Derby Rotation
None
10-255
Motor rotation, slow to fast
Technical Specifications
• Power supply: 100-240V AC, 50/60Hz
• Power consumption: 45W
• Light Source:
o Derby: 2pcs 12W RGBW LEDs
o Strobe: 24pcs 0.2w SMD White LEDs
o Laser: 532nm/30mW (Green) laser diode, 650nm/100mW (red) laser diode
• Lifetime: 50,000 hours
• Control Panel: 4 digital LED display figures
• Control Mode: Sound activated, Auto, Master/Slave, DMX512, IR Remote
• DMX Channels: 2 / 11
• Dimensions: 320x320x320 (package)
• Weight: 3.35kg
Warranty
Please refer to your local dealer or contact Event Lighting Pty Ltd.