Event Lighting SABER2 User manual

SABER2
3-in-1 Disco Effect Featuring Derby, UV and Strobe
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.
Product Installation
SABER2 can be mounted in many orientations, provided each individual device is secured by the
use of the correct mounting bracket. Use a safety chain when mounting SABER2 overhead.

www.event-lighting.com.au
2
Dimensions

www.event-lighting.com.au
3
Control Panel
Buttons
(1) MENU – Select program functions.
(2) ENTER – Confirm the selected function.
(3) UP – Increase parameters.
(4) DOWN – Decrease parameters.
Input and Output
(5) IEC power in.
(6) 3-pin DMX in.
(7) 3-pin DMX out.

www.event-lighting.com.au
4
Menu
Display
Function
Value/Description
Addr
DMX Address
A001-A512
SLAV
Master/Slave
No/Yes
A1-1 ~ A1-9
Derby effects
Red, 1-9 to adjust motor speed.
A2-1 ~ A2-9
Derby effects
Green, 1-9 to adjust motor speed.
A3-1 ~ A3-9
Derby effects
Blue, 1-9 to adjust motor speed.
A4-1 ~ A4-9
Derby effects
White, 1-9 to adjust motor speed.
A5-1 ~ A5-9
Derby auto mode
1-9 to adjust run speed.
A6-1 ~ A6-9
UV effects
No function. Manual UV control only allows one level.
A7-1 ~ A7-9
Strobe effects
1-9 to adjust strobe speed.
A8-1 ~ A8-9
Combined Auto mode
1-9 to adjust auto run speed.
S1-1 ~ S1-9
Sound mode 1
Derby effect, 1-9 to adjust the sound sensitivity.
S2-1 ~ S2-9
Sound mode 2
3-in-1 effect, Blackout when without sound,
1-9 to adjust the sound sensitivity.
S3-1 ~ S3-9
Sound mode 3
3-in-1 effect, Light up when without sound,
1-9 to adjust the sound sensitivity.
DMX Chart
CH
Function
Value
Description
1
Derby Motor rotation
000-127
Directional rotation
128-255
Rotate automatically, fast to slow
2
Derby Motor rotation range
000-255
0 to 340 degrees
3
Derby Master dimmer
000-255
Dimmer 0-100%
4
Derby Strobe
000-010
No Strobe
011-255
Strobe, slow to fast
5
Derby effect
000-255
Red dimmer, 0-100%
6
Derby effect
000-255
Green dimmer, 0-100%
7
Derby effect
000-255
Blue dimmer, 0-100%
8
Derby effect
000-255
White dimmer, 0-100%
9
Derby Auto mode
000-255
Derby Effect auto run
10
Derby Speed Adjust
000-255
Auto run speed, slow to fast
11
UV effect
000-255
UV dimmer, 0-100%
12
UV strobe
000-255
UV strobe, slow to fast
13
Strobe effect
000-255
White dimmer, 0-100%
14
Strobe Speed
000-010
No strobe
011-255
Strobe, slow to fast

www.event-lighting.com.au
5
15
Macros
000-050
Control with channels 1 to 14
051-100
Sound mode 1, derby effect
101-200
Sound mode 2, 3-in-1, blackout when no sound
201-255
Sound mode 3, 3-in-1 auto-run when no sound
Technical Specifications
Power
• Input Voltage: 100~240V AC, 50/60 Hz.
• Power Consumption: 42W.
• Connection: IEC in.
Photometrics
• Light Source:
o Derby: 2pcs 4-in-1 8W RGBW LEDs.
o Strobe: 2pcs 10W White LEDs.
o UV: 8pcs 3W UV LEDs
• LED Lifespan: 50,000 hours.
Effects
• Dimming: 0-100%, 8-bit.
• Strobe: 1-20 Hz.
Control
• Protocol: DMX512.
• DMX Channels: 15
• Interface: 3-pin DMX in/out.
• Operation modes: DMX, Manual, auto, sound active, master/slave
• Display: LED Display with 4-button control.
Housing
• Finishing: Matte Black.
• Net Weight: 2.15kg
• Dimensions: 260x260x250 mm (packaging).
Warranty
Please refer to your local dealer or contact Event Lighting.