evertz 7706LT Series User manual

7706LT Series
Extended L-Band Fiber Transmitter
USER MANUAL
© Copyright 2013 - 2016
EVERTZ MICROSYSTEMS LTD.
5292 John Lucas Drive
Burlington, Ontario
Canada L7L 5Z9
Phone: [phone]
Sales: [email protected] Fax: [phone]
Tech Support: [email protected] Fax: [phone]
Web Page: www.evertz.com
Version 1.1, September 2016
The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of
purchasers of the 7706LT series product. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the operation
of the 7706LT series product. Due to on going research and development, features and specifications in this manual are subject to change without
notice.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz Microsystems Ltd. Copies of
this manual can be ordered from your Evertz dealer or from Evertz Microsystems.

This page left intentionally blank

IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “Dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (Servicing) instructions
in the literature accompanying the product.
•Read these instructions
•Keep these instructions.
•Heed all warnings.
•Follow all instructions.
•Do not use this apparatus near water
•Clean only with dry cloth.
•Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
•Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
•Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than other. A grounding-type plug has two blades and a third grounding prong.
The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
•Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles and the point where they exit from the apparatus.
•Only use attachments/accessories specified by the manufacturer
•Unplug this apparatus during lightning storms or when unused for long periods of time.
•Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC –
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE
WARNING
DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING
AND ENSURE THAT NO
OBJECTS FILLED WITH LIQUIDS ARE PLACED ON THE EQUIPMENT
WARNING
TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE
POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE
WARNING
THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE

INFORMATION TO USERS IN EUROPE
NOTE
CISPR 22 CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to the European Union EMC directive. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
INFORMATION TO USERS IN THE U.S.A.
NOTE
FCC CLASS A DIGITAL DEVICE OR PERIPHERAL
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
WARNING
Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s
authority to operate the equipment.
Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables
with the shield connected to the chassis ground of the device must be used.
EN60065
Safety
EN504192 2005
Waste electrical products should not be
disposed of with household waste. Contact
your Local Authority for recycling advice
EN55103-1: 1996
Emission
EN55103-2: 1996
Immunity

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - i
TABLE OF CONTENTS
1. OVERVIEW...................................................................................................................................1
2. INSTALLATION............................................................................................................................3
2.1. 7706LT CONNECTIONS ......................................................................................................4
2.2. CARE AND HANDLING OF OPTICAL FIBER .....................................................................4
2.2.1. Safety........................................................................................................................4
2.2.2. Assembly...................................................................................................................5
2.2.3. Labelling....................................................................................................................5
2.2.4. Handling and Connecting Fibers................................................................................6
3. SPECIFICATIONS.........................................................................................................................7
3.1. RF INPUT .............................................................................................................................7
3.2. RF MONITOR OUTPUT........................................................................................................7
3.3. OPTICAL OUTPUT ..............................................................................................................7
3.4. RF SYSTEM PERFORMANCE 7706LT+7706LRA PAIR.....................................................7
3.5. ELECTRICAL.......................................................................................................................7
3.6. PHYSICAL (NUMBER OF SLOTS) ......................................................................................7
3.7. COMPLIANCE......................................................................................................................8
4. STATUS INDICATORS.................................................................................................................9
5. JUMPER POSITIONS.................................................................................................................11
5.1. 7706LT JUMPERS AND LEDS ..........................................................................................11
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED BY THE GLOBAL
FRAME STATUS................................................................................................................11
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES ........................................12
5.4. FACTORY AND BDM JUMPERS.......................................................................................12
6. DOT-MATRIX DISPLAY..............................................................................................................13
6.1. 7706LT CONTROLLED PARAMETERS............................................................................16
6.1.1. Adjusting the RF Input Power Alarm........................................................................16
6.1.2. Selecting the Input Gain Mode ................................................................................16
6.1.3. Enabling/Disabling Squelch Mode...........................................................................17
6.1.4. Adjusting the Squelch Mode Threshold ...................................................................17
6.1.5. Adjusting the RF Gain .............................................................................................17
6.1.6. Adjusting the AGC Target Level ..............................................................................18
6.1.7. Setting the Passcode (DWDM versions only) ..........................................................18
6.1.8. Setting the LNB Voltage Level.................................................................................18
6.1.9. Configuring the 22KHz Tone ...................................................................................19
6.1.10. Setting the LNB Current Threshold Level ................................................................19
6.1.11. Default Card-Edge Display......................................................................................19

7706LT
Extended L-Band RF Fiber Transmitter
Page - ii Revision 1.1
6.1.12. Setting the Display Orientation................................................................................19
6.1.13. Displaying the RF Threshold ...................................................................................20
6.1.14. Displaying the Gain Mode .......................................................................................20
6.1.15. Displaying the Gain Level........................................................................................20
6.1.16. Displaying the Squelch Status.................................................................................20
6.1.17. Displaying the Laser Status.....................................................................................21
6.1.18. Displaying the LNB Voltage Level ...........................................................................21
6.1.19. 22KHz Tone Status .................................................................................................21
6.1.20. Displaying the LNB Current.....................................................................................21
6.1.21. Displaying the LNB Current Threshold Level...........................................................21
6.1.22. Displaying the Firmware Version.............................................................................22
FIGURES
Figure 1-1: 7706LT Block Diagram...................................................................................................................1
Figure 2-1: 7706LT Module ..............................................................................................................................3
Figure 2-2 Reproduction of 7706LT Certification and Identification Label for Models that are Class 1 Laser
Products............................................................................................................................................................5
Figure 2-3 Reproduction of 7706LT Certification and Identification Label for Models that are Class 1M Laser
Products............................................................................................................................................................6
Figure 5-1: Location of 7706LT Jumpers and LEDs.......................................................................................11
TABLES
Table 4-1: LED Status Indicators....................................................................................................................10
Table 6-1: Card Edge Menu Structure............................................................................................................15

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - iii
REVISION HISTORY
REVISION DESCRIPTION DATE
1.0 First Release Mar 2013
1.1 Updates throughout Sep 2016
Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor
for the rights of third parties, which may be affected in any way by the use thereof. Any representations in this document concerning
performance of Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The
only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order
confirmation form.
Although every attempt has been made to accurately describe the features, installation and operation of this product in this manual, no
warranty is granted nor liability assumed in relation to any errors or omissions unless specifically undertaken in the Evertz sales contract or
order confirmation. Information contained in this manual is periodically updated and changes will be incorporated into subsequent editions. If
you encounter an error, please notify Evertz Customer Service department. Evertz reserves the right, without notice or liability, to make
changes in equipment design or specifications.

7706LT
Extended L-Band RF Fiber Transmitter
Page - iv Revision 1.1
This page left intentionally blank

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 1
1. OVERVIEW
The 7706LT is a fiber optic transmitter for RF signals in the extended L-Band or wider frequency range.
It accepts a single RF input on coaxial cable and provides a single output for optical transmission. An
RF monitor provides a convenient means of obtaining peak satellite signal strength, or additional signal
distribution.
Gain may be adjusted manually or managed automatically via AGC. 13/17V DC adjustable LNB power
with 22kHz tone is also provided.
Features:
•Extended frequency response for L-Band signals
•Protocol independent design - transports all modulation formats
•LNB power with selectable 13/17V DC
•LNB current limit & short circuit protection
•22kHz tone on/off for LNB local oscillator control
•RF monitor output for signal peaking and signal distribution
•Manual gain and AGC modes for tuning optimal CNR performance
•Fiber link provides electrical isolation between antenna and facility, mitigating ground loop and
lightning issues
The 7706LT occupies one card slot and can be housed in a 1RU frame that will hold up to three
modules, a 350FR that will hold up to seven modules or a standalone enclosure which holds one
module.
Figure 1-1: 7706LT Block Diagram

7706LT
Extended L-Band RF Fiber Transmitter
Page - 2 Revision 1.1
This page left intentionally blank

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 3
2. INSTALLATION
The 7706LT comes with a companion rear plate appropriate for a 1RU, 3RU or standalone enclosure
as specified at the time of order. SC/UPC, SC/APC, ST/UPC, FC/UPC, FC/APC or ST/UPC optical
connectors are available and the type specified at the time of order will be installed. For information on
mounting the rear plate and inserting the module into the frame, see the 7700FR manual for detailed
instructions.
Figure 2-1: 7706LT Module

7706LT
Extended L-Band RF Fiber Transmitter
Page - 4 Revision 1.1
2.1. 7706LT CONNECTIONS
FIBER OUTPUT: SC/UPC, SC/APC, FC/UPC, FC/APC or ST/UPC female connector with the
optical output from the 7706LT. This connector should be connected to the
FIBER IN connector of an appropriate Evertz companion receiver model at the
destination end with a suitable fiber optic cable. The 7706LT may transmit
1310nm, CWDM or DWDM wavelengths as indicated by the part number on the
card ejector. The standard connector type is UPC. This connector type is
compatible with standard PC connectors, but for optimal return loss performance,
Evertz recommends the use of UPC fiber terminations throughout the system.
The optional APC connectors provide further enhanced return loss performance,
and when specified, should be used throughout the system.
RF IN: Input connector for RF signals. This connector can also provide LNB power and
22 kHz tone back to the LNB.
RF OUT: Output connector provides a buffered copy of the incoming RF signal for
monitoring purposes (signal peaking, etc.) or coaxial distribution. Although not
essential, if this connector is to remain unused, it is recommended that it be
terminated with an appropriate 75 Ohm or 50 Ohm load.
The RF input is protected to the same degree as other professional RF
devices, and will withstand a degree of ESD from handling, etc. Regardless,
proper precautions should be taken during handling, such as the use of static
bags and wrist straps.
The input is not protected against lightning or other
coupling of large energy spikes. If the installation is such that the RF input
may be susceptible to spikes (e.g. direct connection to the antenna/LNB) then
appropriate supplemental surge protection should be installed (e.g.
Polyphaser).
2.2. CARE AND HANDLING OF OPTICAL FIBER
2.2.1. Safety
2.2.1.1. 7706LT 1310nm FP and CWDM Versions
!
CLASS 1 LASER PRODUCT
Background colour: yellow
Triangular band: black
Symbol: black

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 5
2.2.1.2. 7706LT DWDM Versions
!
INVISIBLE LASER RADIATION
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
Background colour: yellow
Triangular band: black
Symbol: black
2.2.2. Assembly
Assembly or repair of the laser sub-module is to be done only at the Evertz facility and performed only
by Evertz technical personnel.
2.2.3. Labelling
Certification and Identification labels are combined into one label. As there is inadequate space on the
product to place the label, it is reproduced here in the manuals.
•There is no date of manufacture on this label as it can be traced by bar code label placed on the
PCB of each Evertz plug-in product
•Class 1 Laser Products: Model number is one of 7706LT or 7706LTxx (xx = 27, 29, 31, 33, 35, 37,
43, 45, 47, 49, 51, 53, 55, 57, 59, 61)
•Class 1M Laser Products: Model number is one of 7706LTDxxx (Dxxx represents ITU Grid
Channel: D200, D210, D220, D230, D240, D250, D260, D270, D280, D290, D300, D310, D320,
D330, D340, D350, D360, D370, D380, D390, D400, D410, D420, D430, D440, D450, D460, D470,
D480, D490, D500, D510, D520, D530, D540, D550, D570, D580, D590, D600)
Figure 2-2 Reproduction of 7706LT Certification and Identification Label for
Models that are Class 1 Laser Products

7706LT
Extended L-Band RF Fiber Transmitter
Page - 6 Revision 1.1
Figure 2-3 Reproduction of 7706LT Certification and Identification Label for
Models that are Class 1M Laser Products
2.2.4. Handling and Connecting Fibers

Never touch the end face of an optical fiber. Always keep dust caps on optical fiber
connectors when not connected and always remember to properly clean the optical
end facet of a connector before making a connection.
The transmission characteristics of the fiber are dependent on the shape of the optical core and
therefore care must be taken to prevent fiber damage due to heavy objects or abrupt fiber bending.
Evertz recommends that the user maintain a minimum bending radius of 5 cm to avoid fiber-bending
loss that will decrease the maximum attainable distance of the fiber cable. Evertz fiber optic modules
are equipped with lockout devices that prevent the user from damaging the fiber connector by installing
a module into a slot in the frame that does not have a suitable rear plate installed.

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 7
3. SPECIFICATIONS
3.1. RF INPUT
Number of Inputs: 1
Connector: BNC per IEC 61169-8 Annex A (F-Type and SMA Optional)
Input Impedance: 75Ω (50Ω Optional)
Return Loss: > 15dB (>10dB for 50Ω)
Frequency Range: 850MHz-2250MHz
Input Power Range: -10dBm to -60dBm
AGC Gain Range: -10 to +30dB
Input IP3: +10dBm
LNB Power
Voltage: 13V DC, 17V DC, off (selectable)
Current: 400mA
Protection: Short Circuit, current limited
LO Control: 22kHz on/off (selectable)
3.2. RF MONITOR OUTPUT
Number of Outputs: 1
Connector: BNC per IEC 61169-8 Annex A (F-Type and SMA Optional)
Output Impedance: 75Ω (50Ω Optional)
Return Loss: > 15dB (>10dB for 50Ω)
Frequency Range: 850MHz to 2250MHz
Output Level: within -2.0dB of input signal
3.3. OPTICAL OUTPUT
Number of Outputs: 1
Connector: Female FC/UPC, ST/UPC, FC/UPC, SC/APC, FC/APC
Operating Wavelength
Standard: 1310nm DFB
Output Power:+2dBm
3.4. RF SYSTEM PERFORMANCE 7706LT+7706LRA PAIR
Frequency Range: 850MHz-2250MHz
Flatness: ±1.5dB
3.5. ELECTRICAL
Voltage: +12V DC
Power: 6W max excluding LNB Power
3.6. PHYSICAL (NUMBER OF SLOTS)
350FR: 1
7700FR-C: 1
7800FR: 1

7706LT
Extended L-Band RF Fiber Transmitter
Page - 8 Revision 1.1
3.7. COMPLIANCE
Laser Safety: Class 1 laser product
Complies with 24 CFR 1040.10 and 1040.11 IEC 60825-1
EMI/RFI: Complies with FCC Part 15, Class A
EU EMC directive

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 9
4. STATUS INDICATORS
The 7706LT has eight LED status indicators on the front card edge to show operational status of the
card at a glance. See Figure 5-1 for LED locations.
Two large LEDs on the front of the board indicate the general health of the module:
LOCAL FAULT: This red LED will be on during the absence of a valid RF input signal (too
low, too high or out of AGC range), an LNB short/overload, or if a local
internal power fault exists (i.e.: a blown fuse). Whether or not this LOCAL
FAULT indication is reported to the frame may be selected by the FRAME
STATUS jumper (see section 5.1).
MODULE OK: This green LED will be on when the RF input signal is within range, LNB
power conditions are normal and the board power is good.
There are six small LEDs that indicate the status of the input RF signal, LNB, and AGC mode signals.
RF HIGH: This red LED will be on when the input RF signal is higher than the RF
high threshold setting.
RF OK: This green LED will be on when the input RF signal is within threshold
settings.
RF LOW: This yellow LED will be on when the input RF signal is lower than the RF
low threshold setting.
GAIN MODE: This LED is on when AGC mode is enabled and off when Manual mode is
enabled. It will be green when power levels are within the AGC hold
range and a constant RF output level is being maintained. It will be red if
power levels are either above or below the power levels required for the
AGC circuit to be able to maintain a constant level.
LNB MODE: This LED is on when LNB power is ON. It will green when LNB is active
and OK (no short). It will be red when an LNB short or overload is
detected (fault present).
SQUELCH MODE: This LED is on when squelch is enabled. It will be green when squelch is
enabled but not active. It will be red when squelch mode is enabled and
the output signal is squelched.

7706LT
Extended L-Band RF Fiber Transmitter
Page - 10 Revision 1.1
LED #
Colour
Function
LOCAL /
FAULT
RED
LED 1 is red or LED 2 is off or LED 3 is yellow or LED 4 is red or LED 5 is red.
GREEN
LED 1 is off and LED 2 is green and LED 3 is off and LED 4 is green or off
and LED 5 is green or off.
1
RED
RF Input Power is greater then or equal to the upper threshold setting.
OFF
RF Input Power is less then the upper threshold setting.
2 GREEN
RF Input Power is less the upper threshold setting and greater then the lower
threshold setting.
OFF
RF Input Power is less then the lower threshold setting or greater then the
upper threshold setting.
3
YELLOW
RF Input Power less then or equal to the lower threshold setting.
OFF
RF Input Power greater then the lower threshold setting.
4
RED
AGC is on but unable to maintain output power setting.
GREEN
AGC is on and can maintain output power setting.
OFF
AGC is off (manual mode)
5
RED
LNB Short/Overload
GREEN
LNB power on and OK
OFF
LNB power OFF
6
RED
Squelch active
GREEN
Squelch on but not active
OFF
Squelch off
Table 4-1: LED Status Indicators

7706LT
Extended L-Band RF Fiber Transmitter
Revision 1.1 Page - 11
5. JUMPER POSITIONS
5.1. 7706LT JUMPERS AND LEDS
/ MODULE OK
LOCAL FAULT
AGC Status
Squelch Status
DOT MATRIX DISPLAY
RF High
RF OK
RF Low
RUN/UPGRADE
FRAME
STATUS
OFF/ON
J6
Serial Upgrade Port
Pushbutton
Toggle
Switch
BDM
FACTORY
LNB Power Status
Figure 5-1: Location of 7706LT Jumpers and LEDs
5.2. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS
The FRAME STATUS jumper J3 determines whether local faults (as shown by the Local Fault indicator)
will be connected to the 7700FR frame's global status bus.
FRAME STATUS: To monitor faults on this module with the frame status indicators (on the Power
Supply FRAME STATUS LEDs and on the Frame's Fault Tally output) install this
jumper in the ON position (default).
When this jumper is installed in the Off position local faults on this module will not
be monitored.

7706LT
Extended L-Band RF Fiber Transmitter
Page - 12 Revision 1.1
5.3. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES
UPGRADE: The UPGRADE jumper J5 is used when firmware upgrades are being done to the
module. For normal operation it should be installed in the RUN position. See the
Upgrading Firmware section of this manual for more information.
5.4. FACTORY AND BDM JUMPERS
When shipped from the Evertz facility, the FACTORY and BDM jumpers will not be installed. These
jumpers should not be installed for any reason. If jumpers are on these positions they should be
removed.