Ezviz DP1 User manual

www.ezvizlife.com

1
Attention
•Do not expose the camera to the harsh environment like high temperature, humid,
salt mist, or rain, otherwise, the device may be damaged.
•Do not press the sensor or lens of the camera, otherwise, the device may be
damaged.
•Do not pull the wire of the camera hardly, and protect yourself from being cut by
the wire. Damage to the wire due to inappropriate operation is not included in the
warranty.
•Use the exclusively power adapter to charge the panel, otherwise, the system may
be damaged.
Box Content
Camera (x1) Panel (x1) Mounting Base (x1)
Screws (x3) Base Buckle (x1) Wire Buckle (x1)
Cable (x1) Power Adapter (x1) Quick Start Guide (x1)

2
Overview
Power on/off Touch Screen
Micro SD Card Slot
Wakeup Button Sensor Power Interface
LoudspeakerCamera Interface
Sensor
Bell
Sensor
Lens
Panel
Camera
Do not block the sensors.

3
Panel Interface
Mounting Hole
Hook
Camera Interface
Installation
•If you used to install the peephole, remove it and install the device in the same place. If
not, please drill a hole of diameter about 16.5 to 30mm and about 145cm distance from
the ground to have a good viewing effect.
Measure the door's thickness and select
the appropriate screw.
Thickness Screw
35 to 60mm
60 to 85mm
85 to 100mm
Mounting Base
For hanging portable charger.

4
Turn the screw into the back of camera. Tear off the release paper.
Pass screw and wire through the door.
You can roll up the paper to help.
Adjust camera's position and
push it close to the door gently.
Connect the mounting base
with the camera's wire.
Insert the buckle and
press it tightly to fix it.

5
Adjust the mounting base's
position and tighten the screw.
Put the wires in the groove
and insert the buckle.
Slide the panel into the mounting base. Hold the power button to power on the panel.
Power on
Hold the power button for 3 to 5 seconds
to power up the panel.

6
Album
Record
Set
Tap to set detailed parameters as
you desired such as Display, Monitoring,
Date, and etc.
Connect to Wi-Fi
1 2
Display Monitoring Bell Setting Date
Firmware InfoStorageRestore Wi-Fi
Settings
3
t
Wi-Fi
Manual Connect Mobile Setup
4
xxxxx
yyyyy
Manual Connect
Select your Wi-Fi and enter password.

7
Add to EZVIZ App
1Create an user account.
-Connect your mobile phone to Wi-Fi.
-Download and install the EZVIZ app by searching “EZVIZ” in App Store and Google
PlayTM.
-Launch the app and register an EZVIZ user account following the start-up
wizard.
2Add a camera to EZVIZ.
-Log in the EZVIZ app.
-On the Home screen, tap “+” on the upper-right corner to go to the scan QR
code page.
-Scan the QR code.
XXXX
XXXX
XXXX
XXXX
Firmware Info
Tap Firmware Info to view the QR code.

8
Charge the Panel
Connect the panel with the power outlet via power adapter.
Power Outlet
Power Adapter
•Recommended Charging Time: 5 to 6 hours.
•You can also charge the panel via portable charger and hang it on the hook.

9
Achtung
•Setzen Sie die Kamera keinen widrigen Umgebungsbedingungen wie hohen
Temperaturen, Feuchtigkeit, Salznebel oder Regen aus, da das Gerät dadurch
beschädigt werden kann.
•Quetschen Sie nicht den Sensor oder das Kameraobjektiv, da das Gerät dadurch
beschädigt werden kann.
•Ziehen Sie nicht am Kamerakabel und vermeiden Sie Abrisse. Schäden am Kabel
aufgrund unsachgemäßen Gebrauchs sind von der Garantie nicht abgedeckt.
•Verwenden Sie zum Laden des Bildschirms nur das mitgelieferte Netzteil, da sonst das
System beschädigt werden kann.
Inhalt
1x Kamera Bildschirm (x1) Montagefuß (x1)
Schrauben (x3) Fußschnalle (x1) Kabelschließe (x1)
Kabel (x1) Netzteil (x 1) Kurzanleitung (x1)