Ezviz CS-W2D User manual

www.ezvizlife.com

COPYRIGHT © 2019 Hangzhou EZVIZ Software Co., Ltd. ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou EZVIZ
Software Co., Ltd. (hereinafter referred to as “EZVIZ”). This user manual (hereinafter referred to as “the Manual”) cannot
be reproduced, changed, translated, or distributed, partially or wholly, by any means, without the prior written permission
of EZVIZ. Unless otherwise stipulated, EZVIZ does not make any warranties, guarantees or representations, express or
implied, regarding to the Manual.
About this Manual
The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information
hereinafter are for description and explanation only. The information contained in the Manual is subject to change,
without notice, due to firmware updates or other reasons. Please find the latest version in the ™ website
(http://www.ezvizlife.com).
Revision Record
New release – January, 2019
Trademarks Acknowledgement
™, ™, and other EZVIZ’s trademarks and logos are the properties of EZVIZ in various jurisdictions.
Other trademarks and logos mentioned below are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND EZVIZ MAKES NO WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL EZVIZ, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA
OR DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF EZVIZ HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL EZVIZ’S TOTAL LIABILITY FOR ALL
DAMAGES EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT.
EZVIZ DOES NOT UNDERTAKE ANY LIABILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE AS THE RESULT OF PRODUCT
INTERRUPTION OR SERVICE TERMINATION CAUSED BY: A) IMPROPER INSTALLATION OR USAGE OTHER THAN AS
REQUESTED; B) THE PROTECTION OF NATIONAL OR PUBLIC INTERESTS; C) FORCE MAJEURE; D) YOURSELF OR THE THIRD
PARTY, INCLUDING WITHOUT LIMITATION, USING ANY THIRD PARTY’S PRODUCTS, SOFTWARE, APPLICATIONS, AND AMONG
OTHERS.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.
EZVIZ SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES
RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,
EZVIZ WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS AND DATA PROTECTION LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS TO THE APPLICABLE LAW.
EZVIZ SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THE ABOVE AND THE APPLICABLE LAW, THE LATTER PREVAILS.
Regulatory Information
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This product generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radiocommunications.
However, there is no guarantee that interference will not occur in a particular installation. If this product does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Please take attention that changes or modification not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the Radio Equipment
Directive 2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

SAVE THIS MANUAL FOR FUTURE REFERENCE
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.
Гарантийный срок-1 год
Срок службы-3 года
Производитель:Ханджоу Хиквижн Диджитал Технолоджи(Китай)
Импортер-поставщик в России: ЗАО ''Хиквижн''
Импортер-поставщик в Республике Беларусь:ООО ''Торговый Дом ''АВАНТ-
ТЕХНО''
Сайт:www.ezviz.ru
EC DECLARATION OF CONFORMITY
Hereby, Hangzhou EZVIZ Software Co.,Ltd . declares that the radio equipment type [CS-W2D] is in compliance with Directive
2014/53/EU.
The full text of the EC DECLARATION OF CONFORMITY is available at the following web link:
http://www.ezvizlife.com/declaration-of-conformity.
Safety Instruction
Due to the product shape and dimension, the name and address of the importer/
manufacturer are printed on the package.
Customer Service
For more information, please visit www.ezvizlife.com.
Need help? Please visit “www.ezvizlife.com/inter/page/contact-us” for our local contact details.

1
Camera
Microphone
LED Indicator
Loudspeaker
SYNC Button
Lens
PIR
Photoresistor
Power Interface
SD Card Slot
Name Description
SYNC Button Hold for 5 seconds to get the camera ready for Wi-Fi configuration.
PIR With the PIR (Passive Infrared), the device can detect a human body to
determine when there is a possible break in and begins to record footage.
LED Indicator • Solid Red: Camera is starting up.
• Solid Blue: Video is being viewed in the EZVIZ app.
• Slow-Flashing Blue: Camera is working.
• Slow-Flashing Red: Camera is charging/Network exception.
• Fast-Flashing Blue: Camera is ready for Wi-Fi configuration.
• Fast-Flashing Red: Exception/Low battery.
Photoresistor
Detects the environment's light conditions to activate the Day/Night switch function.
SD Card • Recommended compatibility: Class 10, Max.128GB.
• Format the card in the EZVIZ app before using it.
Power Interface For charging the battery or powering up the camera.

2
Base Station
Power Button
Main Button/LED indicator
Network Interface/Network Indicator
Power Interface Reset
Button
Name Description
LED Indicator • Solid Green: The system works properly.
• Solid Blue: Device is not connected to internet.
• Flashing Blue: Device starting synchronization with the camera.
• Off: The base station is turned off.
Main Button Press to start synchronization with the camera (The synchronization lasts 2 mins).
Power Button Press to connect or cut off power.
Network Indicator • Solid Green: The network cable is connected.
• Flashing Green: Data transmission is working.
• Off: The network cable is disconnected.
Reset Button Hold for 7 seconds to to restart and reset all parameters to default.

3
Setup
Step 1 Insert Battery into Camera
- Press the button as shown below to open battery cover.
- Insert the battery.
- Close the battery cover.
Please fully charge the battery before the first time use.
Step 2 Charge the Battery
- Connect the camera with power outlet via power adapter (5V 1A).
Power Outlet
Power Adapter
Use the exclusive charger to charge the battery.

4
Step 3 Power on the Base Station
- Wait until the LED indicator turns to solid blue. 5V 2A
Step 4 Connect Base Station to Internet via Network Cable
- Connect the base station to the LAN interface of your router with the network cable.
Make sure network indicator is on or flashing.
Step 5 Synchronize Base Station with Camera(s)
• Make sure the camera is within 2' to 3' (0.6 m to 1 m) of the base station.
• The synchronization process lasts about 2 minutes.
1. Press the Main Button on the base station. The circular LED indicator flashes Blue.

5
2. Press and hold the Sync button on the camera for 5 seconds. The LED indicator will slowly
flash blue. When flashing blue becomes more rapid and then stops, sync is confirmed.
Fast-Flashing Blue: Synchronization complete.
Fast-Flashing Red: Sync failed. Repeat the Sync Process.
You can sync up to 6 cameras to each base station at the same time.
Step 6 Add the Base Station to Your EZVIZ Account
1. Create an user account.
- Connect your mobile device to the Internet.
- Search “EZVIZ” in App Store or Google PlayTM to download.
- Launch the App and register an EZVIZ user account.
2. Add Base Station to EZVIZ.
- Log in the EZVIZ App.
- At the Home screen, tap “+” on the upper-right corner to go to the scanning QR code interface.

6
- Scan the QR Code on base station or manually enter the Serial Number to add base
station.
NetworkVideo Recorder
Model:xxxxx
IP:xxxxx
SN:xxxxx
MM/YYYY
VerificationCode:xxxxx
- Tap the “Add” button to finish setup. This will take approximately 1minute.
- Tap “View Camera” to start using and viewing your camera(s) in the mobile app.
Camera Installation
• Camera and base station should be within the distance of up to 300 feet (100 m). Stay away
from wireless device or barriers to avoid decreasing the communication distance.
• Your camera provides a 126-degree viewing angel. Position your cameras to make sure the
scene you want to video is in the cameras’ field of view.
• Your camera motion sensor is far more sensitive to side-to-side movement across their field
of view. The best area for motion detection is 5 feet to 25 feet (1.5 to 7.5 meters) from the
camera position.

7
Step 1 Pick a clean and flat surface, indoors or outdoors.
126°
Top View
Step 2 Secure the magnetic mount with the screw.
Step 3 Mount the camera to the magnetic mount or attach it directly to a magnetic surface.

8
Box Contents
Camera Battery Magnetic Mount
USB Cable Power Adapter Screw Kit
The number of the products above is subject to the actual ones you selected.
Base Station (x1) Network Cable (x1)
USB Cable (x1) Power Adaptor (x1) Quick Start Guide (x1)
For detailed information, please refer to www.ezvizlife.com.

9
Caméra
Microphone
Indicateur lumineux
Haut-parleur
Bouton SYNC
Lentille
PIR
Photorésistance
Port
d'alimentation
Emplacement
pour carte
mémoire SD
Nom Description
Bouton SYNC Patientez 5secondes pour que la caméra soit prête pour la configuration du Wi-Fi.
PIR La fonction PIR (infrarouge passif) permet à l’appareil de détecter une
présence humaine en cas d’intrusion et de démarrer l’enregistrement.
Indicateur lumineux • Rouge continu: la caméra est en cours de démarrage.
• Bleu continu: la vidéo est en cours de visionnage dans l’applicationEZVIZ.
• Clignotement lent en bleu: la caméra est en cours de fonctionnement.
• Clignotement lent en rouge: la caméra est en charge/problème de réseau.
• Clignotement rapide en bleu: la caméra est prête pour la configuration du Wi-Fi.
• Clignotement rapide en rouge: une erreur s’est produite/batterie faible.
Photorésistance
Cette fonction permet de détecter les conditions d’éclairage du milieu afin d’activer la
commutation Jour/nuit.
Carte mémoire SD • Compatibilité recommandée: carte microSD de classe10, 128Go max.
• Formatez la carte présente dans l’applicationEZVIZ avant de l’utiliser.
Port d'alimentation Permet de charger la batterie ou de mettre la caméra sous tension.

10
Station de base
Touche d'alimentation
Bouton principal/
Indicateur lumineux
Interface réseau/Indicateur réseau
Port d'alimentation Boutonde
réinitialisation
Nom Description
Indicateur lumineux • Vert continu: le système fonctionne correctement.
• Bleu continu: l’appareil n’est pas connecté à Internet.
• Clignotement en bleu: L’appareil démarre la synchronisation avec la caméra.
• Désactivé: La station de base est désactivée.
Bouton principal Permet de démarrer la synchronisation avec la caméra (l’opération dure 2min).
Touche
d'alimentation
Permet de mettre sous ou hors tension.
Indicateur réseau • Vert continu: Le câble réseau est connecté.
• Clignotement en vert: la transmission des données est en cours.
• Désactivé: Le câble réseau est déconnecté.
Bouton de
réinitialisation
Maintenez-le enfoncé pendant 7secondes pour redémarrer et restaurer tous
les paramètres aux valeurs par défaut.

11
Configuration
Étape1 Installer la batterie dans la caméra
- Appuyez sur le bouton indiqué ci-dessous pour ouvrir le couvercle du compartiment à batterie.
- Insérez la batterie.
- Remettez en place le couvercle du compartiment à batterie.
Chargez entièrement la batterie lors de sa toute première utilisation.
Étape2 Charger la batterie
- À l’aide de l’adaptateur d’alimentation (5V/1A), branchez la caméra sur la prise d’alimentation.
Prise électrique
Adaptateur d’alimentation
Utilisez le chargeur exclusif pour recharger la batterie.

12
Étape3 Mettre sous tension la station de base
- Patientez jusqu’à ce que le témoin LED passe au bleu fixe.
5V 2A
Étape4 Connecter la station de base à Internet via le câble réseau
- Connectez la station de base à l’interface LAN de votre routeur à l’aide d’un câble réseau.
Assurez-vous que l’indicateur réseau est allumé ou clignote.
Étape5 Synchroniser la station de base avec la(les) caméra(s)
• Assurez-vous que la caméra est située à une distance de 0,6m à 1m de la station de base.
• La synchronisation dure environ 2minutes.
1. Appuyez sur «Main Button» (Bouton principal) de la station de base. Le voyant LED
circulaire clignote en bleu.

13
2. Appuyez pendant 5secondes sur le bouton SYNC de la caméra. Le voyant LED clignote
lentement en bleu. Lorsque le clignotement s’accélère et s’arrête, cela signifie que la
synchronisation s’est déroulée avec succès.
Clignotement rapide en bleu: la synchronisation s’est déroulée avec succès.
Clignotement rapide en rouge: la synchronisation a échoué. Recommencer la synchronisation.
Vous pouvez synchroniser simultanément jusqu’à 6caméras à chaque station de base.
Étape6 Ajouter la station de base sur votre compte EZVIZ
1. Créer un compte utilisateur.
- Connectez votre appareil mobile à Internet.
- Dans App Store ou Google PlayTM, recherchez et téléchargez l’application EZVIZ.
- Lancez l’application et créez un compte utilisateur EZVIZ.
2. Ajoutez la station de base à EZVIZ.
- Connectez-vous dans l’application EZVIZ.
- Touchez le signe + situé dans le coin supérieur droit de la page Home (Accueil) pour accéder
à l’interface de lecture du code QR.

14
- Scannez le QR code sur la station de base ou saisissez manuellement le numéro de série
pour ajouter la station de base.
NetworkVideo Recorder
Model:xxxxx
IP:xxxxx
SN:xxxxx
MM/YYYY
VerificationCode:xxxxx
- Cliquez sur «Add» (Ajouter) pour terminer la configuration. L’opération dure environ
1minute.
- Appuyez sur «View Camera» (Visionner la caméra) pour commencer à utiliser la ou les
caméra(s) et à en visionner les images sur l’application mobile.
Installation de la caméra
• La caméra et la station de base doivent être installées à une distance pouvant atteindre
300pieds (100m). Éloignez-vous de l’appareil sans fil ou des barrières pour éviter de réduire
la distance de communication.
• Votre caméra possède un angle de vue de 126degrés. Positionnez vos caméras de sorte que
la scène que vous souhaitez filmer apparaisse dans le champ de vision des caméras.
• Le détecteur de mouvement de votre caméra est beaucoup plus sensible aux mouvements
latéraux captés dans le champ de vision. La meilleure zone de détection de mouvement est
de 5pieds à 25pieds (1,5 à 7,5mètres) à partir de la position de la caméra.

15
Étape1 Choisissez une surface plane et propre à l’intérieur ou à l’extérieur.
126°
Vue de dessus
Étape2 À l’aide de la vis, fixez le support magnétique sur la surface choisie.
Étape3 Fixez la caméra sur le support magnétique. Vous pouvez aussi la fixer directement sur une
surface magnétique.