Honeywell Home TUXEDOW User manual

TuxedoW Home Automation
and Security System
User Guide
800-25177B 4/19 Rev. B

NOTE: This device is a Security Enabled Z Wave Controller

Table of Contents
INTRODUCTION ........................................................................................................................................................................................1
About this guide...................................................................................................................................................................................1
Features ..............................................................................................................................................................................................1
NAVIGATING THE TUXEDOW INTERFACE ............................................................................................................................................2
On the Home screen ...........................................................................................................................................................................2
System Information..............................................................................................................................................................................2
Weather Forecast................................................................................................................................................................................2
Wi-Fi Cameras.....................................................................................................................................................................................2
Icons and Their Meanings ...................................................................................................................................................................3
System Trouble Icons..........................................................................................................................................................................4
User Codes..........................................................................................................................................................................................5
Status LED ..........................................................................................................................................................................................5
Safe Mode ...........................................................................................................................................................................................5
OPERATING YOUR SECURITY SYSTEM ................................................................................................................................................6
Arming Modes .....................................................................................................................................................................................6
Arming the System ..............................................................................................................................................................................7
How to Bypass Zones..........................................................................................................................................................................8
Disarming the System .........................................................................................................................................................................9
FIRE AND CARBON MONOXIDE ALARM OPERATION .......................................................................................................................11
In Case of Fire Alarm.........................................................................................................................................................................11
Silencing and Clearing a Fire/Carbon Monoxide Alarm.....................................................................................................................11
MORE CHOICES......................................................................................................................................................................................12
How to Clear/Hide a Control Panel Message ....................................................................................................................................12
Advanced System Features...............................................................................................................................................................12
How to View the Event Log ...............................................................................................................................................................13
HOW TO SEND EMERGENCY MESSAGES...........................................................................................................................................13
SETUP......................................................................................................................................................................................................14
System Information............................................................................................................................................................................14
System Setup ....................................................................................................................................................................................14
System Wi-Fi .....................................................................................................................................................................................15
Account .............................................................................................................................................................................................15
DISPLAY & AUDIO ..................................................................................................................................................................................16
Brightness and Volume Controls .......................................................................................................................................................17

MULTIMEDIA APPLICATION..................................................................................................................................................................17
Slideshow Setup................................................................................................................................................................................18
Video Setup.......................................................................................................................................................................................19
TIME/DATE SETUP .................................................................................................................................................................................20
Daylight Savings Time.......................................................................................................................................................................20
CS SETUP................................................................................................................................................................................................21
USER SETUP...........................................................................................................................................................................................21
Authority Levels.................................................................................................................................................................................21
How to Add a User ............................................................................................................................................................................22
How to Add an Existing User to a Second Keypad............................................................................................................................22
How to Delete a User ........................................................................................................................................................................22
How to Edit a User.............................................................................................................................................................................22
ADVANCED SETUP ................................................................................................................................................................................23
Power Mode Setup............................................................................................................................................................................23
Night Setup........................................................................................................................................................................................23
Keypad Reset....................................................................................................................................................................................23
End-User License..............................................................................................................................................................................24
Factory Default ..................................................................................................................................................................................24
Safe Mode .........................................................................................................................................................................................24
Tuxedo Sync......................................................................................................................................................................................26
User Profile........................................................................................................................................................................................26
Quick Programming...........................................................................................................................................................................27
Controller Initial..................................................................................................................................................................................27
AUTOMATION .........................................................................................................................................................................................28
Z-Wave Icons ....................................................................................................................................................................................28
Including (Adding) Z-Wave Devices in Your System .........................................................................................................................29
Including a Z-Wave Door Lock ..........................................................................................................................................................30
Wi-Fi Thermostat Programming.........................................................................................................................................................31
EXCLUDING (REMOVING) Z-WAVE DEVICES IN YOUR SYSTEM ......................................................................................................32
Excluding a Light, Switch or Outlet Module .......................................................................................................................................32
Excluding a Resideo Thermostat.......................................................................................................................................................32
Excluding a Door Lock.......................................................................................................................................................................33
i

ABORT A Z-WAVE ACTION ...................................................................................................................................................................33
Remove Failed Devices.....................................................................................................................................................................33
Device Setup .....................................................................................................................................................................................34
Replace Failed Device.......................................................................................................................................................................34
Default the Z-Wave Controller ...........................................................................................................................................................35
SCENE SETUP ........................................................................................................................................................................................36
Scene Rules ......................................................................................................................................................................................36
Sample Scene ...................................................................................................................................................................................37
Critical Events....................................................................................................................................................................................37
Scene Setup Options.........................................................................................................................................................................37
CREATE A ROOM ...................................................................................................................................................................................40
SETTING A SECONDARY (KEYPAD) CONTROLLER...........................................................................................................................40
Updating Controllers (Keypads) with New or Removed devices........................................................................................................41
Removing a Secondary Controller (Keypad) .....................................................................................................................................41
Z-WAVE TROUBLESHOOTING ..............................................................................................................................................................41
TOTAL CONNECT ...................................................................................................................................................................................42
Total Connect Setup..........................................................................................................................................................................42
Controlling Automation (Z-Wave) Devices Remotely.........................................................................................................................43
Creating Scenes with Total Connect .................................................................................................................................................43
Enabling Devices for Total Connect ..................................................................................................................................................43
Total Connect Server Screen for Troubleshooting.............................................................................................................................44
NOTES ON Z-WAVE DEVICES AND TUXEDOW ...................................................................................................................................44
COMPATIBLE DEVICES .........................................................................................................................................................................45
WIRELESS RANGE .................................................................................................................................................................................46
ROUTINE CARE ......................................................................................................................................................................................46
TWO YEAR LIMITED WARRANTY .........................................................................................................................................................47

TuxedoW Home Automation and Security System User Guide
1
Introduction
Congratulations on your purchase of a TuxedoW touchscreen-controlled security system. TuxedoW is a touchscreen keypad that
controls your Vista security system. The clear, simple controls are easy to learn and easy to use. Press in the lower right corner of
the screen to see videos with step-by-step tutorials on setting up and customizing your system.
About this guide
•TuxedoW is occasionally referred to simply as 'Tuxedo' throughout
•The term system refers to the entire Vista-based security system
•The terms 'user code' and 'authorized code' are used interchangeably
•The illustrations in this guide may differ slightly from what you see on your touchscreen
Features
TuxedoW offers burglary protection and options for fire/carbon monoxide protection as well as programmable Panic buttons for other
types of emergency. (Panic buttons must be initially set up by your installer.)
Typically, your system is set up to automatically transmit alarms or status messages to a central alarm monitoring station.
TuxedoW can also control compatible devices such as wireless light switches and dimmer modules, door locks, thermostats, water
valve monitoring devices and cameras.
In addition to the TuxedoW touchscreen, your system may include:
•One or more additional touchscreen keypads
•Window and door sensors for burglary protection
•Smoke, carbon monoxide or combustion detectors
•Lighting controls and other home automation devices
The system monitors all the sensors in your home, displaying alerts and other status information on the touchscreen(s). The sensors
are grouped into zones to provide concise, useful information in an emergency. See Introduction to Security System Operation on
page 6for more about the zones on your premises.
Total Connect
TuxedoW supports the Total Connect remote service for controlling Z-Wave devices and Scenes. For more information, see page 42.

TuxedoW Home Automation and Security System User Guide
2
Navigating the TuxedoW interface
Working with TuxedoW typically begins on the Home screen. This is the default display you'll see once system setup is complete. By
default, the Home screen is displayed at most times; it can be customized via the Multimedia application.
On
the Home screen
•Arm and disarm the Security system. See page 6for
more information.
•Manage Multimedia features including display of
videos and pictures on the touchscreen. See page 17
.
•Control home Automation Devices such as lights,
locks and thermostats. See page 28.
System
Information
For the current
software and software versions and other
system
information, touch at lower right on the Home
screen
.See page 14.
Weather Forecast
The weather forecast is displayed in the upper right corner of the Home screen. Touch the Weather graphic to set the forecast for your
location. On the weather settings screen, touch the Region dropdown to set the country where you live. Touch the Zip Code/Postal
Code field to enter the code for your location. Touch at lower left on the Weather screen to update the forecast.
Note that your system must be connected to the Internet to receive weather information.
Wi-Fi Cameras
TuxedoW is compatible with camera models iPCAM-PT, iPCAM-PT2, iPCAM-PT2A, iPCAM-WI2 and iPCAM-WI2B.
Ready To Arm7:00 AM
tuxedow-001-V1

TuxedoW Home Automation and Security System User Guide
3
Icons and Their Meanings
ICON FUNCTION ICON FUNCTION
Home: Returns display to the Home screen.
Authorized Code:
Use to enter 4-digit user code.
Security: When green, arms the system in one
of three arming modes. When red,
touch to disarm the system.
Multimedia:
Controls slideshow and video features
Panic: Displays Emergency functions (as
programmed by the installer).
Note: This icon is displayed and
active on all screens except while in
the Clean Screen mode.
Keypad Reset:
Press to reset the Touchscreen.
Setup: Accesses setup screens for System
Info, System Setup, System Wi-Fi,
Account, Display & Audio Setup and
Brightness / Volume.
Adjusts display brightness and notifications
volume.
Apply: Press to accept changes.
More Choices:
Access to Event Logs, Console Mode
and Show Zones
Wi-Fi: Accesses Wi-Fi setup screens. Used
to connect to Wi-Fi networks (if
installed and programmed by your
installer).
Disp & Audio Setup:
Accesses setup screens for voice
notifications, screen backlighting,
Homepage configuration, temperature
display and other personalization
options.
Control Panel Message:
Alerts user to a control panel
message.
Voice Status Sounder:
Press to hear system status verbally.
Micro SD card loaded

TuxedoW Home Automation and Security System User Guide
4
System Trouble Icons
The Security screen displays one or more of these icons if system troubles occur. If a Trouble icon appears, contact your security
professional.
ICON
FUNCTION
AC Loss – The system is not receiving AC power.
Bell Failure – The system bell or siren has a problem. Note: This icon appears only in residential systems.
Expander Failure – There is a failure in an expansion module. If this notification appears, contact your security professional.
Low Battery – The battery that powers the system during an AC power loss is low.
LRR Supervision Failure – The communication device used to communicate with the central station has a supervision failure.
Max Attempts Exceeded – The system has exceeded the maximum number of attempts to communicate with the Central Station.
Pager Failure – The system cannot communicate with an assigned pager.
Telco-1 Cut – The system is not able to communicate with the central monitoring station over the primary phone line.
Telco-2 Cut – The system is not able to communicate with the central monitoring station over the secondary phone line.
Wireless Failure – The system is not able to communicate with its wireless devices.

TuxedoW Home Automation and Security System User Guide
5
User Codes
When users are added to the system, each is assigned a 4-digit user code. This code enables the user's access to features and
functions which she or he is authorized to use. For more information about assigning codes and defining each user's privileges, see
page 22.
Extended Functionality
Extended functions are those that can be accessed through a standard alpha keypad or through the Console Emulation Mode on the
TuxedoW Touchscreen. Refer to the alarm system's user guide for more information on these features.
Status LED
The LED to the left of the touchscreen shows different colors to indicate status:
To reset the system, press and hold the side power/reset button for 3 seconds and then touch the Press Here to Reset message on
the screen to begin the reset process. The system can also be reset by pressing and holding the power/reset button for approximately
15 seconds, until the system resets automatically.
Safe Mode
In the rare event your TuxedoW cannot successfully communicate in its graphic mode with the rest of the system, Safe Mode offers a
backup method to ensure that you can operate the system. See Safe Mode on page 24 for more information.

TuxedoW Home Automation and Security System User Guide
6
Operating Your Security System
Arming Modes
You can enable protection in any of these three arming modes: Away, Stay and Night.
Mode Function Exit
Delay Entry Delay Perimeter
Armed
Interior
Armed
AWAY
Press to arm when no one is staying on the
premises. When armed in AWAY mode, the
system sounds an alarm if a protected door or
window is opened, or if any movement is
detected inside the premises.
Yes Yes Yes Yes
STAY
Press to arm when you are staying home but
might expect someone to use the entrance
door later.
When armed in STAY mode, the system
sounds an alarm if a protected door or
window is opened, but movement within the
premises is not monitored.
Yes Yes Yes No
NIGHT
Press to arm when you are staying home and
do not expect anyone to use the entrance
door. Your installer may have configured
NIGHT Mode differently than the default
settings; have the installer explain the specific
settings of NIGHT Mode.
Yes
Yes (set for Away or
Stay Mode)
No (set for Instant or
Maximum Mode)
Yes
Yes (set for Away or
Maximum Mode)
No (set for Stay or
Instant Mode)
See Night Mode note below
NOTES: On commercial systems, Away Auto Stay mode is displayed as Away (with all zones monitored). However, some
interior zones may not be armed.
On residential systems only, Night Mode arms all perimeter zones plus all zones listed in your system's Zone List 5.
Refer to the system's documentation for more information on Zone Lists.
The Voice Status Sounder icon indicates the Voice feature. Touch the Voice Status Sounder icon to hear system status. Wait
3 seconds and press again to hear Zone Faults or Trouble conditions. Voice status will annunciate even if Voice mode and Chime
mode are disabled. Note that the Voice feature must be enabled (by the installer) for this icon to function correctly during an alarm
condition.
There is a communicator delay of 30 seconds. This delay will prevent a report to the central station if the system is disarmed within
30 seconds after an intrusion alarm is triggered. This delay can be removed, or it can be increased up to 45 seconds at the option
of the user by consulting with the installer. Note that emergency, carbon monoxide, and fire-type alarms are normally reported
without delay.

TuxedoW Home Automation and Security System User Guide
7
Arming the System
Note: Close all protected exterior ("perimeter") windows and doors before arming. To arm the system:
ICON ACTION NOTES
1. From the Home screen, touch the Security icon.
2. Press the selected arming icon.
•A text message appears stating which
zones types are arming and whether or not
there is an entry delay
•The screen changes to display the
remaining exit delay time, and…
•The exit delay time continues counting
down to 1.
NOTE:If Quick Arm is not enabled in your system, a prompt to
enter your User Code is displayed.
When the system is armed for Stay, Night Stay and Instant
mode, the touchscreen beeps 3 times.
When the system is armed for Away and Maximum mode, you
will hear steady beeps then rapid beeping during the last 10
seconds of Exit Delay.
When exit delay time expires, the screen automatically changes
to indicate the system is "Armed".
How to Display Faults
The Display Faults function is used when you see a Not Ready Fault message and want to determine where the fault is and what type
of fault it is. To display faults, do the following:
ICON ACTION NOTES
1. Touch the following icons:
Security → More Choices →Show Zones.
Select the down arrow to view faults.
You can also press the icon to display
faults.
2. If the fault cannot be corrected, you may
choose to bypass a zone by selecting it,
highlighting it and then touching the Bypass
Selected icon.
The drop-down menu displays a listing of fault types. Select the fault
type to view and current status is displayed on the screen.
Take corrective action as needed, such as closing windows or doors to
correct the fault.
Distressed Zones Icons
Alarm Troubles Faults Bypass
Low
Battery
All

TuxedoW Home Automation and Security System User Guide
8
How to Bypass Zones
The Bypass function is used when you want to arm the system with one or more zones left open. Bypassed zones are unprotected and
do not cause an alarm when violated while the system is armed.
•Residential systems do not allow bypassing fire, carbon monoxide or emergency zones. On commercial fire
systems, a
specified user may be allowed to bypass fire, carbon monoxide and system zones, but that user must be enabled to do
so by the system installer.
•There are limits on the number of zones that can be bypassed at one time. On residential systems, ten (10) zones can
be bypassed at once; on commercial systems, the limit is five (5).
To bypass zones, do the following:
ICON
ACTION
NOTES
1. From the Home screen, touch the Security
and More Choices icons. Note: If any zones are bypassed or faulted, a Display Faults icon is also
displayed on this screen.
2. Press the Show Zones icon. While the touchscreen is requesting and receiving the zone data from the
system, the screen displays Please Wait! Then the zones and their current
status are displayed.
3. Highlight the zone(s) to be bypassed and
touch the Bypass Selected icon.
4. Enter the 4-digit user code.
Note: If zones have already been bypassed, the top of this screen says
Ready Bypass and To Bypass Zones, Enter Code.
5. Touch the Refresh Data icon. The More Choices screen is displayed showing the system status
Ready-Bypass.
How to Clear Bypassed Zones
Bypassed zones are automatically un-bypassed when the system is disarmed. To un-bypass a zone manually, take these steps:
SCREEN
ACTION
NOTES
1. Touch the SHOW ZONES icon.
2. Touch the CLEAR BYPASSES icon.
3. Enter your 4-digit user code. The More
Choices screen is displayed showing the
system as Ready to Arm.
While the touchscreen is requesting and receiving zone data from
the system, the screen displays Please Wait! Then the zones and
their current status are displayed.
NOTE: If the system is armed, un-bypassing a zone will disarm
the system. If zones are still faulted (not ready) the system
will show the status
Not Ready Fault
.

TuxedoW Home Automation and Security System User Guide
9
Disarming the System
IMPORTANT: If you return to your home or business and the main burglary alarm is sounding, DO NOT enter the premises, but call
the police from a safe location nearby. If you return to your home or business after an alarm has occurred and the main sounder has
shut itself off, the keypad beeps rapidly upon entering, indicating that an alarm has occurred during your absence.LEAVE
IMMEDIATELY and CONTACT THE POLICE
from a safe location nearby.
The system may be disarmed using either of two methods. One method is employed when you enter the premises and the other is
when you have been in the premises with the system armed (i.e., Stay and Night arming modes).
To disarm the system when entering the premises:
The touchscreen automatically displays Entry Delay Active when you enter the premises.
ICON ACTION NOTES
Enter your 4-digit user code.
The partition is disarmed and the Arming screen displays Ready
to Arm. (See page 10 for more about Partitions.)
NOTE:If you have a commercial system and a time window has
been defined for when you may disarm the system, the system
does not disarm if you are outside that time window.
To disarm the system when you're on the premises:
ICON ACTION
1. Press the Disarm button
2. Enter your 4-digit user code.
To disarm Multi-Partitions:
ICON ACTION NOTES
1. Touch the Security icon.
2. Touch the Arm Multi-Partition icon.
3. Touch the Disarm icon.
4. Enter your 4-digit user code.
5. Highlight the partition(s) to disarm and press
OK
or press
ALL
to disarm all partitions.
All selected partitions should be disarmed, user can enter multi-
partition list to check the status of partitions.

TuxedoW Home Automation and Security System User Guide
10
How to Check the Status of Other Partitions
This system supports between one and eight Partitions (depending on the system.) Partitioning enables a single physical alarm system
to control up to eight areas of protection (partitions) depending on the system you have purchased. Each Touchscreen is assigned a
default partition for display purposes and shows only that partition's information.
NOTE:A letter “H” following the partition name or number indicates that this is the default partition for the touchscreen. For example, if
your physical site is a four-apartment housing unit, your alarm system may be configured with four partitions. Each apartment’s
zones (door, windows, smoke detectors, etc.) are assigned to separate partitions, giving each apartment independent
arming/disarming control of its own partition (area). A landlord or manager may be granted access to all partitions, so he/she can
control the entire system.
If a user is so authorized, a touchscreen or other touchscreen in one partition can be used to perform system functions in another partition.
(Note that only those partitions authorized and programmed by the installer can be accessed in this manner.)
To check the status of other partitions, perform the following:
ICON
ACTION
NOTES
1. Touch the Security icon.
2. Select the Current Partition icon; in this
case it displays P1 H unless changed by
the installer).
3. Enter the code authorized to access other
partition(s).
If the code is accepted, the system displays
the partitions that user has access to.
This screen displays the available partitions and their current status.
The current partition is shown at the top of the display (P1). To
change this assignment, select the appropriate icon (e.g., press P2
to switch control to Partition 2).
NOTE: After leaving this screen when using a residential system,
the selected partition in the touchscreen automatically reverts back
to the touchscreen’s home partition after two minutes. When using
commercial systems, you must select the touchscreen’s home
partition to return to it.
NOTE: A code may have access to some or all of the available
partitions.

TuxedoW Home Automation and Security System User Guide
11
Fire and Carbon Monoxide Alarm Operation
Your fire alarm system and carbon monoxide detector (if installed) is on 24 hours a day, providing continuous protection. In the event
of an emergency, the installed smoke, heat, carbon monoxide detectors automatically send signals to your Control/Communicator,
triggering a loud interrupted sound from the touchscreen. An interrupted sound is also produced by optional exterior sounders.
EVACUATE ALL OCCUPANTS FROM THE PREMISES IMMEDIATELY. Notify your Central Station/Security Company immediately
and wait for further instructions.
In Case of Fire Alarm
A FIRE message appears at your touchscreen and remains on until you silence the alarm.
•Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest touchscreen and
manually initiate an alarm by pressing the panic key assigned as FIRE emergency (if programmed by the installer) and hold
down for at least 2 seconds.
•Evacuate all occupants from the premises.
•If flames and/or smoke are present, leave the premises and notify your local Fire Department immediately.
Silencing and Clearing a Fire/Carbon Monoxide Alarm
1. Silence, acknowledge, and clear the alarm by:
a. For Residential Systems: Press Touch here to Silence on the display to silence the alarm.
For Commercial Systems: Enter your code; this action silences the alarm and acknowledges disarming the system (if it was
armed at the time of the alert).
b. For Residential Systems: Press the CLEAR icon followed by your code. This acknowledges the alarm and the disarming of
the system (if armed).
For Commercial Systems: Press the CLEAR icon followed by your code. The system attempts to clear the alarm from
memory. If NOT successful (i.e., smoke in the detector) the Security screen is displayed and the Display Faults icon displays a
“Not Ready Fault”.
c. Press the DISPLAY FAULTS icon on the Arming screen. The faulted fire/carbon monoxide zone is displayed.
d. Press the CLEAR icon and then enter your code. This clears the Fire Alarm/CO Alarm from the system.
2. If the touchscreen does not indicate a READY condition after the second sequence, press the DISPLAY FAULTS key on the
Arming screen to display the zone(s) that are faulted. Be sure to check that smoke detectors/carbon monoxide detectors are not
responding to smoke, heat, or gas producing objects in their vicinity. In this case, eliminate the source of heat, smoke or leak.
3. If this does not remedy the problem, there may still be smoke/gas in the detector. Clear it by fanning the detector for about 30
seconds.
4. When the problem has been corrected, clear the display by entering the DISPLAY FAULTS icon on the Arming screen, selecting
the fire or carbon monoxide zone, pressing the CLEAR icon and then entering your user code.
Note: Contact your Central Station/Security Company for servicing if you have further problems with your system.

TuxedoW Home Automation and Security System User Guide
12
More Choices
How to Clear/Hide a Control Panel Message
The icon alerts the user to a control panel message. When a Control Panel Message is displayed, the user has two options. The
user can clear the message immediately or minimize the window and clear it at a later time.
To Clear/Hide the Control Panel Message, do the following:
ICON
ACTION
NOTES
1. To clear, press CLEAR.
2. Enter your 4-digit user code or:
3. To hide, press HIDE to clear the Control
Panel Message later.
Once your user code is accepted, the Control Panel Message is cleared.
If the alarm is still present, press CLEAR again and then enter your user
code again.
Press the HIDE icon to address the condition later.
Advanced System Features
While most of the commonly used security functions are available from the touchscreen’s advanced user interface, there are some less
used, advanced features that can either be accessed through Console Emulation mode on the touchscreen or a standard alpha
keypad. To use features not supported by the touchscreen, refer to the system's user guide.
Console Emulation Mode
Console Emulation Mode allows you to use a touchscreen interface just as you would a regular system touchscreen. All commands
shown in Console Emulation mode can also be executed from a standard alpha keypad.
Notes:
•Using Console Emulation Mode to enter GOTO commands is not recommended. Unsatisfactory operation may result from issuing
GOTO commands in Console Emulation mode.
•Two-icon Panics (1 &*, 3 &# and * &#) do not function in Console Emulation Mode. The A, B, C, and D icons do function if
programmed as Panic keys. Check with your system installer for details.
•On commercial systems with alphanumeric keypads ONLY:
oPressing a key for 5 seconds calls up Help information about functions associated with that key.
oPressing the *key for 5 seconds displays information on zone descriptors.
How to Initiate Console Emulation Mode
ICON ACTION NOTES
1. From the Home screen, touch the Security
icon.
2. Touch the More Choices icon
3. Touch the Console Mode icon.
Perform functions as you would from a standard alpha keypad.

TuxedoW Home Automation and Security System User Guide
13
How to View the Event Log
Your system records events in its operation in a log; each event is logged with the time and date of its occurrence. Logging must be set
up by your installer. To view the Event Log, do the following:
ICON ACTION NOTES
1. From the Home screen, touch the Security icon
and then the More Choices icon.
2. From the Event Logs menu, select the Events
drop-down arrow to view the logged history of
events. Your choices are: All Events, System,
Alarms, Troubles, Bypasses, and
Open/Close.
3. Select the Partitions drop-down arrow to open
and view the partitions list.
NOTE: While keypad is requesting and receiving the event log
data from the system, the "Event Log" screen displays "Please
Wait!"
The Next>> and <<Previous icons are shown for commercial
systems only when 100 or more events are in the log. They are
not shown for residential systems.
When more than 100 events exist, pressing All Partitions or
All Events displays the Next >> and << Previous icons,
indicating the previous 100 events or the next 100 events.
How to Send Emergency Messages
Fire, police or medical emergency messages can be sent to the central monitoring station from the Emergency screen.
Press the PANIC icon at lower left on the screen to open the Emergency screen.
Take these steps to send an emergency message:
ICON ACTION NOTES
PANIC
1. Press the PANIC icon and hold it for at least
2 seconds
2. Press the FIRE,POLICE,Silent Panic or
MEDICAL icon.
The screen from which you pressed the
PANIC icon reappears.
•The Emergency screen cannot be accessed while the
touchscreen is in Clean Screen mode.
•Emergency messages are optional and might not be included
with your account. Ask your security professional if emergency
messages are configured and available on your system.
Emergency Icons
Fire Police Silent Panic Medical

TuxedoW Home Automation and Security System User Guide
14
Setup
The Setup screen is used to set your preferences and configure other details of the system's operation. Setup provides access to
System Info, System Setup, System Wi-Fi, Account, Display & Audio Setup, Brightness and Volume.
Some of these settings may require that you enter your user code.
On the Home screen, touch the circled gear icon in the lower right corner. The Setup screen appears.
On each screen, press in the upper left corner to return to the previous screen. Press to return to the Home screen.
System Information
ICON
ACTION
On the Setup screen, touch System Info for details on your system's software and firmware and the keypad's internet
connection.
oSelect the Enable Remote Upgrade checkbox to allow over-the-air firmware and software updates
o
Touch SYNC IP TO SERVER to confirm Tuxedo's connection to the internet.
System Setup
ICON ACTION
On the Setup screen, touch System Setup to access these functions and features:
Time/Date Setup page 20
C/S Setup page 21
User Setup page 21
Advanced Setup page 23
Tuxedo Sync page 26
User Profile page 26
Quick Programming page 27
Controller Initial page 27