FAAC 770 COMPACT User manual

In-ground Swing Gate Operator
UL325 - UL991
770
FAAC International Inc.
Headquarter & East Coast Operations
3160 Murrell Road
Rockledge, FL 32955
Tel. [phone]
www.faacusa.com
FAAC International Inc.
West Coast Operations
357 South Acacia Avenue
Fullerton, CA 92831

2
IMPORTANT SAFETY INFORMATION 3
Important Safety Instructions 3
Important Installation Instructions 3
General Safety Precautions 4
UL325 Gate Operator Classifications 5
Installing the Warning Signs 5
1. DESCRIPTION & SPECIFICATIONS 6
1.1. Technical Specifications 6
1.2. Dimensions 6
1.3. Electrical Setup 6
2. INSTALLATION 7
2.1. Preliminary Checks 7
2.2. Installing the foundation box 7
2.3. Setting up the gate 7
2.4. Installing the Operator 8
3. POSITIVE STOPS 9
4. MANUAL OPERATION 9
4.1. Restoring Normal Operation 9
5. MAINTENANCE AND REPAIRS 9
6. SPARE PARTS DIAGRAM 10
E024U CONTROL BOARD 12
TABLE OF CONTENTS
770 Rev. B September 2016

3
1. Install the gate operator only when the following
conditions have been met:
• The operator is appropriate for the type and usage
class of the gate.
• All openings of a horizontal slide gate have been
guarded or screened from the bottom of the gate
to a minimum of 4 feet (1.25 m) above the ground
to prevent a 2.25 inch (55 mm) diameter sphere
from passing through openings anywhere in the
gate or through that portion of the adjacent fence
that the gate covers when in the open position.
• All exposed pinch points are eliminated or guarded.
• Guarding is supplied for exposed rollers.
2. The operator is intended for installation on gates used
by vehicles only. Pedestrians must be provided with a
separate access opening.
3. To reduce the risk of entrapment when opening and
closing, the gate must be installed in a location that
allows adequate clearance between the gate and
adjacent structures. Swinging gates shall not open
outward into public access areas.
4. Before installing the gate operator, ensure that the
gate has been properly installed and that it swings
freely in both directions. Do not over-tighten the
operator clutch or pressure relief valve to compensate
for a damaged gate.
5. User controls must be installed at least 6 feet (1.83 m)
away from any moving part of the gate and located
where the user is prevented from reaching over, under,
around or through the gate to operate the controls.
Controls located outdoors or those that are easily
accessible shall have security features to prevent
unauthorized use.
6. The Stop and/or Reset buttons must be located within
line-of-sight of the gate. Activation of the reset control
shall not cause the operator to start.
7. All warning signs and placards must be installed
and easily seen within visible proximity of the gate.
A minimum of one warning sign shall be installed on
each side of the gate.
8. For gate operators that utilize a non-contact sensor
(photo beam or the like):
• See instructions on the placement of non-contact
sensors for each type of application.
• Exercise care to reduce the risk of nuisance tripping,
such as when a vehicle trips the sensor while the
gate is still moving.
• Locate one or more non-contact sensors where
the risk of entrapment or obstruction exists, such as
at the reachable perimeter of a moving gate or
barrier.
• Use only “FAAC Photobeam” or “EMX IRB-RET” photo-
electric eyes to comply with UL325.
Important Installation Instructions
WARNING - TO REDUCE THE RISK OF SEVERE INJURY OR
DEATH:
• READ AND FOLLOW ALL INSTRUCTIONS.
• Never let children operate or play with the gate
controls. Keep remote controls away from children.
• Always keep people and objects away from the
gate. NO ONE SHOULD CROSS THE PATH OF A
MOVING GATE.
• Test the gate operator monthly. The gate MUST
reverse on contact with a rigid object or when an
object activates a non-contact sensor. If necessary,
adjust the force or the limit of travel and then retest
the gate operator. Failure to properly adjust and
retest the gate operator can increase the risk of injury
or death.
• Use the manual release mechanism only when the
gate is not moving.
• KEEP GATE PROPERLY MAINTAINED. Have a qualified
service person make repairs to gate hardware.
• The entrance is for vehicles only. Pedestrians must use
a separate entrance.
• SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INFORMATION
Important Safety Instructions

4
Gate Construction
Vehicular gates should be constructed and installed in
accordance with ASTM F2200: Standard Specification
for Automated Vehicular Gate Construction.
For more information, contact ASTM at: www.astm.org
Installation
• If you have any questions or concerns regarding the
safety of the gate operating system, do not install the
operator and consult the manufacturer.
• The condition of the gate structure itself directly
affects the reliability and safety of the gate operator.
• Only qualified personnel should install this equipment.
Failure to meet this requirement could cause severe
injury and/or death, for which the manufacturer
cannot be held responsible.
• The installer must provide a main power switch that
meets all applicable safety regulations.
• It is extremely unsafe to compensate for a damaged
gate by increasing hydraulic pressure.
• Install devices such as reversing edges and photo
beams to provide better protection for personal
property and pedestrians. Install reversing devices
that are appropriate to the gate design and
application.
• Before applying electrical power, ensure that voltage
requirements of the equipment correspond to the
supply voltage. Refer to the label on your gate
operator system.
Usage
• Use this equipment only in the capacity for which it
was designed. Any use other than that stated should
be considered improper and therefore dangerous.
• The manufacturer cannot be held responsible
for damage caused by improper, erroneous or
unreasonable use.
• If a gate system component malfunctions,
disconnect the main power before attempting to
repair it.
• Do not impede the movement of the gate, you
may injure yourself or damage the gate system as a
result.
• This equipment may reach high thermal
temperatures during normal operation, therefore use
caution when touching the external housing of the
gate operator.
• Use the manual release mechanism according to
the procedures presented in this manual.
• Before performing any cleaning or maintenance
operations, disconnect power to the equipment.
• All cleaning, maintenance or repair work must be
performed by qualified personnel.
General Safety Precautions
9. For gate operators that utilize a contact sensor (edge
sensor or similar):
• Locate one or more contact sensors where the risk
of entrapment or obstruction exists, such as at the
leading edge, trailing edge, and post mounted
both inside and outside of a vehicular horizontal
slide gate
• Locate one or more contact sensors at the bottom
edge of a vehicular vertical lift gate.
• Locate one or more contact sensors at the bottom
edge of a vertical barrier (arm).
• Locate one or more contact sensors at the pinch
point of a vehicular vertical pivot gate.
• Locate hard-wired contact sensors and wiring so
that communication between sensor and gate
operator is not subjected to mechanical damage.
• Locate wireless contact sensors, such as those
that transmit radio frequency (RF) signals, where
the transmission of signals are not obstructed or
impeded by building structures, natural land-
scaping or similar hindrances. Wireless contact
sensors shall function under their intended end-use
conditions.
• Use only FAAC MSE MO, CN60 or M60 edge sensors.
Important Installation Instructions (continued)

5
RESIDENTIAL VEHICULAR GATE OPERATOR CLASS I
A vehicular gate operator system intended for use in a single family dwelling, garage or associated parking area.
UL325 Gate Operator Classifications
COMMERCIAL / GENERAL ACCESS VEHICULAR GATE OPERATOR CLASS II
A vehicular gate operator system intended for use in commercial locations or buildings such as multi-family housing
units (five or more single family units), hotels, parking garages, retail stores or other buildings that service the general
public.
INDUSTRIAL / LIMITED ACCESS VEHICULAR GATE OPERATOR CLASS III
A vehicular gate operator system intended for use in industrial locations or buildings such as factories, loading docks
or other locations not intended to service the general public.
RESTRICTED ACCESS VEHICULAR GATE OPERATOR CLASS IV
A vehicular gate operator system intended for use in guarded industrial locations or buildings such as airport security
areas or other restricted access locations that do not service the general public, and in which unauthorized access
is prevented via supervision by security personnel.
This FAAC swing gate operator is supplied with two warning
signs to alert people that a possible hazard exists and that
appropriate actions should be taken to avoid the hazard
or to reduce exposure to it.
Permanently install one warning sign on each side of the
gate so they are fully visible to traffic and pedestrians.
Use appropriate hardware such as metal screws (not sup-
plied) to permanently install each warning sign.
Installing the Warning Signs

6
1 Support Box
2 Cover Fastening Holes
3 770 Operator
4 Gate Support Bracket
5 Locking Bracket
6 Release Device with Key
7 Operator Ground Connection
8 Articulate lever
9 Pinion
10 Hole for Power Cable
11 Hole for Drain Pipe
12 Operator Fastening Bolts
13 Lubrication Hole
Fig. 1
Fig. 2
1
2
345
8
6
7
9
10
11
12
13
 770 Operators
 Photocells
 Control Unit
 Pushbutton
 Receiver
Power Supply 24 Vdc
Power 70 W
Current 3 A
Maximum Torque 221 lbf.ft (300 Nm)
Temperature Range 4°F +131°F (-20 °C +55°C)
Use frequency 100%
Class of operation Residential
Angular speed 6°/sec
Operator Weight 26 lb (12 Kg)
Max Leaf Opening Angle 110° (140° and 180° with
optional kit)
Protection class IP 67
Operator dimensions 14 x 6 x 5.5 in
(360 x 150 x 140 mm)
Foundation box dimension See Fig. 3
Max Leaf Length 11.5 ft (3.5 m) - 110°
9.8 ft (3 m) - 180°
8.2 ft (2.5 m) - 140°
Max Leaf Weight 1100 lb (500 Kg)
2.1 Preliminary checks
To ensure a correctly operating automated system, the
structure of the existing gate or gate to be built must satisfy
the following requirements:
• Leaf dimensions are within the limits
• The gate swings level
• Smooth, uniform leaf movement, without any irregular
friction during the entire travel
• Existing hinges in good condition
• Positive stops are provided in the fully opened and closed
positions
• There is a minimum clearance between the bottom
edge of gate and ground. See Fig. 6a (where ‘S’ =
thickness of guide bracket)
The FAAC 770 is an electromechanical operator for swing
gates. It is designed for in-ground installation and therefore
does not alter the appearance of the gate.
The supplied support box allows you to setup the gate before
actually installing the operator.
The 770 electromechanical operator is not reversible, so it
ensures a mechanical stop and eliminates the need for an
electric lock.
The 770 Operator is designed and manufactured to au-
tomate vehicular swing gates. Do not use for any other
purpose.
Operator Cable Size
2x AWG 14 (max 30’)
AWG 12 (max 50’)
AWG 10 (max 100')
12⅛
17
6⅛
8½
Fig. 3
* Measurements in Inches
770 OPERATOR
1. DESCRIPTION AND SPECIFICATION
1.1 Technical Specifications
1.2 Electrical Setup
2. INSTALLATION
1.3 Dimensions
Always separate the connection cables of the low voltage
accessories from the high voltage power cables. Use separate
conduits to avoid interference.
The installer is responsible for grounding the gate and operator
systems, for providing the main power breaker switch, and for
making sure that the entire gate system meets all applicable
electrical codes.
Make sure to locate all controls that operate the gate system at
least 6 ft away from any moving parts.

7
min 10 "
2.3 Setting up the gate
Allow the concrete to set before starting this operation.
1. Assemble the release levers on the support bracket, and
fit the latter on the pivot in the foundation box, also inser-
ting the supplied ball (Fig. 8).
Note: grease both the pivot and the ball.
2. Prepare the guide bracket, as follows:
• Use a “U” profile with dimensions indicated in Fig. 9.
S
2½
6⅛
2¼
~12⅜
6⅛
~17⅜
Fig. 5
Fig. 6b
~17⅜
~12⅜
90°
Fig. 7
Ø 1⅜
Fig. 6a
* Measurements
in Inches
* Measurements in Inches
* Measurements in Inches
* Measurements
in Inches
2.2 Installing the foundation box
1. Dig a hole for the foundation box as shown in Fig. 5.
2. Place the foundation box in the hole, refer to the dimen-
sions provided in Figs. 6a and 6b.
The center of the pivot on the foundation box must be per-
fectly aligned with the leaf’s axis of rotation (Figs 6a and 6b).
3. Install a 1-3/8" Liquid Tight Conduit, it must be long
enough to reach from the box to the control unit (Fig. 7).
Install also a second conduit to drain water from the box
(also Fig. 7).
4. Secure the box in place with a concrete pour.
Depending on the nature of the ground, it may be neces-
sary to cast a bed of quick-setting concrete at the bottom
of the hole to avoid future subsidence.
Fig. 8
Fig. 9
min 1.5"

8
Fig. 10a
Fig. 11
Fig. 10b
Fig. 13


Fig. 12
2.4 Installing the operator
1. Open the gate leaf.
2. Place the operator on the fastening bolts on the foun-
dation box, and secure it using the supplied nuts and
washers (Fig. 13).
Note: the exact position of the operator is shown in Fig. 12. In
any case, the operator pinion must be on the opposite side
of leaves opening direction.
3. Manually close the leaf and assemble the supplied driv-
ing levers, as shown in Fig. 13.
Note: grease the operator pinion and the pivots of the two
levers.
4. Install the second operator, if required, by repeating the
operations described above.
5. Install the electronic control unit. Refer to the relative
instructions.
6. Fasten the box cover using the supplied screws (Fig. 14).
• Determine the correct location of the leaf on the “U” profile
with reference to the axis of rotation (Fig. 10a and 10b);
• Close the “U” profile on the post side with a small plate, as
shown in Figs. 10a and 10b.
3. Carefully weld the guide bracket to the support bracket
(Fig. 11).
4. Fit the gate into the guide bracket and fix the top hinge
in place.
IMPORTANT: To ensure trouble-free operation, do NOT weld
the gate leaf to the guide bracket or to the support bracket.
5. Manually verify whether the gate opens and closes com-
pletely and smoothly, stopping at the mechanical travel
stops.

9
If the gate has to be operated manually in the event of a
power outage or fault of the operator, use the keyed release
device on the support bracket (Fig. 1 - Ref. 6). The operator
can be released from both the inside and the outside of the
gate.
Fig. 14
Optional mechanical positive stops can be installed in the
load bearing box as indicated in Fig. 15. They can be adjust-
ed to properly limit the gate leaf travel.
Fig. 15
3. POSITIVE STOPS (optional)
4. MANUAL OPERATION
1.
Fig. 16

 

To operate the leaf manually, proceed as follows:
1. Disconnect power to the system to avoid accidental gate
movement.
2. Open the cover of the lock (Fig. 16 - Ref. 1)
3. Insert the release key in the lock (Fig. 16 - Ref. 2).
4. Turn the key in the direction of the post, as far as it will go
(Fig. 16 - Ref. 3).
5. Pull the lever out (Fig. 16 - Ref. 4).
6. Operate the leaf manually.
Fig. 17



At regular intervals, check the structure of the gate and make
sure that the hinges are in perfect working order.
Periodically lubricate the pivot and ball in the support bracket,
through the lubricating hole shown in Fig. 1- Ref. 13. Make
sure that the pivots of the lever systems, the pinion and the
engagement of the lock on the locking bracket (Fig. 1 - Ref.
5) are always well lubricated, and check the efficiency of the
manual operation.
REPAIRS
For repairs, refer to an authorized FAAC service center.
5. MAINTENANCE
4.1 Restore Normal Operation
To restore normal operation, proceed as follows:
1. Push the lever back into its home position (Fig. 17 - Ref. 1).
2. Insert the release key into the lock and turn it as far as it will
turn in the direction opposite the post (Fig. 17 - Ref. 2).
3. Operate the leaf manually until the lock is engaged in the
locking bracket (Fig. 17 - Ref. 3).
4. Close the cover on the lock.
5. Restore power and test the system

10
1
4
3
2
5
67
6
8
9
Part Part Number Description
1 770770 770 24V Motor
2 716078 Gear Box
3 727158 Gear Box Cover
4 718075 Secondary Shaft
5 718076 Internal Shaft Group
6 719165 Slow Shaft
7 390451 Seal Kit
8 63000452 Cap
9 63000590 V-Ring Seal And Spacer
5. SPARE PARTS DIAGRAMS

11
1
2
3
4
5
6
6
Part Part Number Description
1 63000422 Release Levers Kit With Locks
2 63003015 Steel Ball
3 7271985 Cover Plug
4 727157 Box Cover
5 390477 Articulated Lever
6 424010 Manual Release Assembly

SETTING
+
J24
DL19 DL20 DL21 DL22DL14 DL15 DL16 DL17 DL18
Main power supply 115 V~ 60 Hz
Secondary power
supply
24 Vdc - 16 A max.
(min. 20 Vdc. - max. 36 Vdc.)
Power consumption stand-by = 4W max. = 400 W
Max load per motor 7 A
Accessory power 24 Vdc - 500 mA
Battery charge current 150 mA
Operating temperature -4 °F +131 °F (-20 °C +55 °C)
Protection fuses All self-resetting
Main power fuse 6.3 A Timed
Operating Logics E, A, S, EP, AP, SP, B, C
Operating time out 10 min.
Pause time Programmable (0 to 4 min)
Motor force, speed, ob-
stacle sensitivity, closing
delay
Programmable with
dedicated trimmer
Connector inputs Power supply, Battery,
Radio receiver, USB
Terminal strip inputs Encoder, Open A, Open B, Stop,
Open safety photocell, Closing
safety photocell, Limit switches
Terminal strip outputs Audio Alarm, Lock, Motors,
Accessory power supply
Programming With trimmers,
dipswitches
and pushbutton
RADIO Connector for the radio receiver
BATTERY Connector for the backup battery
J24 Jumper to disable battery charging
(With the jumper present the battery
charger is enabled)
POWER SUPPLY DC Power supply input
TR1 to TR6 Programming Trimmers
+24 LED DC power indicator
SW1 - SETUP Pushbutton for automatic setup
DS1 - DS2 Programming dipswitches
LED ERROR Troubleshooting indicator
USB A USB connection for software upgrade
On the radio connector it’s possible to plug in receivers RP
and RP2. With a single channel radio RP it will be possible to
activate only the OPEN A input, with a dual channel radio RP2
it will be possible to activate both OPEN A and OPEN B inputs.
Plug in the radio board with the component side towards the
internal part of the board.
Make sure you insert or disconnect the board
ONLY with the power off.
1.1 TECHNICAL SPECIFICATIONS 1.2 LAYOUT AND COMPONENTS
1.3 RADIO CONNECTION
Fig. A1
1. E024U CONTROL BOARD DESCRIPTION & CHARACTERISTICS
This manual refers to board version 1D
12

A B STP CL OP
OPEN FSW
24 VDC
Maglock
Encoder
Fig. A2
MOT DL1 DL2
1 ON ON
2 ON OFF
PIN LABEL FUNCTION
2 EASY 2 EASY 2easy BUS input for encoders (S800H and S450H only), XIB and loop detector boards
1 OPEN A N.O. Contact for total opening command
2OPEN B /
CLOSE
OPEN B: N.O. Contact for opening of leaf 1 only
(with only one leaf the opening stops at 50% of traveling)
CLOSE (LOGIC B-C): N.O. Contact for closing command
3 STOP N.C. Contact for stop command
4 FSW CL N.C. Contact for closing safety
5 FSW OP N.C. Contact for opening safety
6 GND (-) 24 Vdc negative
7 GND (-) 24 Vdc negative
8 + 24 24 Vdc positive
9 OUT (-) 24 Vdc negative for safety TX photocell (monitored)
10 FCA 1 Open limit switch Motor 1
11 GND (-) 24 Vdc negative
12 FCC 1 Close limit switch Motor 1
13 FCA 2 Open limit switch Motor 2
14 GND (-) 24 Vdc negative
15 FCC2 Close limit switch Motor 2
LAMP LAMP Audio Alarm output
LOCK LOCK Output for electrical lock, max 5A pulse (DS2 - SW 4=OFF) 12 Vac / 24Vdc
Always ON (maglock): max 1 A (DS2 - SW 4=ON) 24 Vdc
MOT1 MOT 1 Motor 1 output ( first moving motor )
MOT2 MOT 2 Motor 2 output ( second moving motor )
USB A USB Firmware upgrade input
2. INPUT / OUTPUT DESCRIPTION
13

CLOSE SAFETY
OPEN SAFETY
CL OP
FSW
TX
TX
RX
RX
Connection of One Pair of Monitored Opening
Photocells and One Pair of Monitored Closing
Photocells
CLOSE SAFETY
CL OP
FSW
RX TX
Fig. A6
RX= Receiver Photocell
TX= Transmitter Ptotocell
3. SAFETY DEVICE CONNECTIONS
Fig. A7
Entrapment protection
To comply with the UL325 standard for gate operators every
entrapment zone, as defined in ASTMF2200, must be pro-
tected by two independent entrapment protection devices.
One of the devices is inherent in the E024U control boards
design, the other can be external, like a photocell or an
edge sensor.
See this picture for the photocells positioning:
Fig. A3 Closing Safety Devices Opening Safety
Devices
Opening Safety Devices:
Are active only during the gate opening movement, and
are suitable for protecting the area between the opening
leaves and fixed obstacles (walls, etc) against the risk of
entrapment
Closing Safety Devices:
Are active only during the gate closing movement, and are
suitable for protecting the closing area against the risk of
entrapment.
Monitored Devices:
Additionaly the UL325 standard requires that every external
entrapment protection device must be monitored for
presence and correct operation. To comply with this
requirement the E024U control board uses the FAILSAFE
function. This function tests the photocells before each
movement of the operator. In case the test fails the
movement is inhibited. This function is enabled by default
on the Closing Safety Input and can be enabled on the
Opening Safety Input using dip-switch 12 of DS1 ON.
The power supply negative of the transmitter must be
connected to the OUT pin (No.9).
See Fig. A6, A7, A8, A10 for wiring examples.
Connection of One Pair of Monitored Closing Photocells
RX= Receiver Photocell
TX= Transmitter Ptotocell
16” or less
DS1
DS1
14

Only one monitored photocell can be connected to the
Closing or Opening safety inputs. More than one photocell
or other device can be connected to the safety inputs, but
they will not be monitored.
Other devices connected to the safety inputs must have
normally closed contacts and wired in series with the main
monitored sensor.
See the following example of one closing safety monitored
photocell and one non monitored one.
Closing Safety Devices Opening Safety
Devices
Opening/Closing
Safety Devices
Opening/Closing Safety Devices:
They operate during the gate opening and closing move-
ments and are suitable to protect the opening and closing
areas against the risk of impact. Typically these photocells
work in combination with other monitored photocell pro-
tecting closing or opening entrapment zones. In that case
they can’t be monitored so they can only protect against
potential impact on vehicles.
CLOSE SAFETY MONITORED
CL OP
FSW
OPEN / CLOSE SAFETY NOT MONITORED
RX TX
RX TX
OPEN SAFETY MONITORED
RX TX
Connection of Two Pairs of Closing Photocells, One
Monitored and One non Monitored
Fig. A8
Connection of One Pair of Closing Photocells
(monitored), One Pair of Opening Photocells
(monitored) and One pair of Opening/Closing
Photocells (non monitored)
Fig. A10
Fig. A9
CLOSE SAFETY NOT MONITORED
CL OP
FSW
CLOSE SAFETY MONITORED
RX TX
RX TX
RX= Receiver Photocell
TX= Transmitter Ptotocell RX= Receiver Photocell
TX= Transmitter Ptotocell
16” or less
DS1
DS1
15

OPERATING LOGIC
DS 1: SW 1 - SW 2 - SW 3
LOGIC SW 1 SW 2 SW 3 PAUSE
TIME DESCRIPTION
E (default)
Semiautomatic OFF OFF OFF NO One command opens, the next one closes. A command
during opening stops the gate
A
Automatic ON ON ON 0 - 4
min
One command opens, waits for the pause time an then
closes automatically
S
Security OFF OFF ON 0-4
min
One command opens, waits for the pause time and then
closes automatically. If the closing safety is activated or
another command is given during the pause time it closes.
A maintained open command will not hold the gate open
EP
Semiautomatic
step by step
OFF ON OFF NO One command opens, the next one closes. During the mo-
vement a command stops the gate
AP
Automatic
step by step
OFF ON ON 0-4
min
One command opens, waits for the pause time and then
closes automatically. A command during the pause time
holds the gate open
SP
Security
step by step
ON OFF OFF 0-4
min
One command opens, waits for the pause time and then
closes automatically. If the closing safety is activated during
pause time the gate closes in 5 s. A command during pau-
se time holds open the gate
B
Manned Pulsed ON OFF ON NO An open A command opens the gate, an open B com-
mand closes the gate
C
Manned Constant ON ON OFF NO Holding open A active opens the gate, holding Open B acti-
ve closes the gate
For more details on the operating logics please refer to Chapter 11 - Function Logics
4.1 DIP SWITCH DS1 SETTINGS FOR OPERATING LOGIC
4. PROGRAMMING
16

6
TR 3 – SPEED ADJUSTMENT FOR MOTOR1 AND MOTOR 2
Turn clockwise to increase the opening and closing speed
TR 4 – SENSITIVITY ADJUSTEMENT FOR OBSTACLE DETECTION FOR MOTOR 1 AND MOTOR 2
Turn clockwise to increase the sensitivity for obstacle detection.
See Par. 6.3 for more details about the obstacle detection feature
TR 5 – PAUSE TIME ADJUSTMENT ( 0 - 4 min. )
Turn clockwise to increase the pause time.
TR6 - CLOSING DELAY OF LEAF 1 OVER LEAF 2 ADJUSTMENT ( 0 - 15 sec )
Turn clockwise to increase the delay
TR1 – FORCE ADJUSTMENT MOTOR 1
Turn clockwise to increase the opening and closing force
1 min
2 min
3 min
4 min0 sec
30 sec
TR 2 – FORCE ADJUSTEMENT MOTOR 2
Turn clockwise to increase the opening and closing force
4.2 ADJUSTING TRIMMERS
Dip switches DS1: 1 to 3 need
to be set for an operating
mode with PAUSE time for this
adjustment to have any effect
17

BOARD SETUP
DS 1: SW 4 to SW 12
OPENING DELAY SW 4 The opening of leaf 2 is delayed after the opening of leaf 1. This is to avoid
the gate leafs interfering with each other during the initial part of the move-
ment. In case there is only one leaf it has no effect.
0 sec (default) OFF
2 sec ON
REVERSE AND LAST STROKE SW 5 If active, before opening, while the gate is closed, the motors thrust to clo-
se for 2 s to facilitate the release of the electric lock. At closing the motors
are activated for a final stroke after slowdown to facilitate locking of the
electric lock.
inactive (default) OFF
active ON
MAX THRUST AT STARTUP SW 6 With this fuction active the motors work at maximum force at startup (re-
gardless of the force setting) during the initial phase of the movement. Useful
for heavy leaves
inactive (default) OFF
active for 3 sec ON
AUTOMATIC OPENING IN CASE OF
POWER FAILURE
SW 7 If active and with the optional backup battery installed, the board will open
the gate after one minute from the power failure and keep it open.
Within the minute wait it’s always possible to open and close the gate with
a command. If the logic used has a pause time the board will close the
gate when the power comes back.
inactive (default) OFF
active ON
CLOSING SAFETY LOGIC SW 8 With this function you can choose the behavior of the closing safety. With SW8
OFF the gate movement will be reversed as soon as the safety is active, with
SW8 ON the gate will stop when the safety is active and it will reverse only when
the safety is deactivated.
immediate reverse (default) OFF
reverse when cleared ON
SHADOW LOOP CONFIGURATION SW 9 Selects the behavior of the shadow loop function of the XIB accessory
OFF: The shadow loop input is active only before a closing command,
ignored in any other conditions
ON: The shadow loop input is active before a closing and before an opening
command. If an open command is given and the shadow loop input is
engaged the open command will be ignored even after the shadow loop
input goes inactive.
NOTE: On the first power up of the board an open command will be always
executed (even if the shadow loop is engaged), but at reduced speed.
active only on closing (default) OFF
active on closing and opening ON
EXTRA SENSITIVITY TO
OBSTACLE DETECTION
SW 10 If active this function allows to have an immediate reverse in case the gate
hits a rigid obstacle. This function increases the safety of the gate operator,
however it can generate unwanted obstacle detections.
inactive (default) OFF
active ON
24V ACCESSORY VOLTAGE SW 11 Selects the behavior of the 24V accessory voltage during battery mode:
OFF: The accessory voltage and BUS input are turned off in battery
backup mode
ON: The accessory voltage and BUS input are always active even in bat-
tery backup mode
24V OFF in Battery Mode OFF
24V ON in Battery Mode ON
FAIL SAFE MODE SW 12 Selects the behavior of the Fail Safe (monitoring) mode:
OFF: Fail Safe is active on the closing safety photocell input (FSW CL) only
ON: Fail Safe is active on both closing safety photocell input (FSW CL) and
opening safety photocell input (FSW OP)
NOTE: if using the XIB interface the opening safety on it is also monitored.
Refers to the XIB manual for further details.
Closing Safety OFF
Closing and Opening Safety ON
4.3 DIP SWITCH DS1 SETTINGS FOR BOARD SETUP
18

DS2
SETTING
+
J24
1
2
34
5
6
78 9 10
DL19 DL20 DL21 DL22
DL14 DL15 DL16 DL17 DL18
Reserved
DS 2
OPERATOR SELECTION
OPERATOR TYPE SW 1 SW 2 SW 3
S450H, S800H OFF OFF OFF
S418 OFF OFF ON
415, 390, 770 ON OFF OFF
DS 2
LOCK OUTPUT MODE
OUTPUT MODE SW 4
Active only for 3 sec. after an open impulse
(from gate closed) OFF
Active always except 3 sec. before an opening ON
SETTING
+
DL 1 DL 2 DL 3 DL 4 DL 5
J24
IMPORTANT
4.4 DIP SWITCH DS2 SETTINGS FOR OPERATOR TYPE AND LOCK MODE
5. LED DIAGNOSTICS
19

L
E
D
DESCRIPTION
LED STATUS
In BOLD the normal state with gate closed and working
ON STEADY OFF BLINKING
1LED BATTERY Board working on AC
power
Board working on
battery power or ext supply Battery charging
2LED +24 Main power present Main power OFF
3LED SET-UP Normal operation
SLOW BLINK
(1 sec. ON - 1 sec. OFF)
SET-UP needed
FAST BLINK
(0.5 sec. ON - 0.5 sec OFF)
SET UP in in progress
4LED ERROR
Board malfunction.
See possible causes
below
No errors Error conditions.
See LED ERROR DISPLAY table
5LED BUS_MON Communication on
Bus “2easy” OK
Communication bus
“2Easy” inactive. Verify
encoders for shorts
“2Easy” bus devices with the
Same address. Verify
encoder LEDs
6LED USB2 Software update done
or USB key not present
USB key inserted and software
Update in progress
(DON’T Remove the USB key)
7LED USB1 Normal operation
Number of flashes show version at
power up:
No Flashes=1C | One flash =1D
8
LED DL 14
OPEN A INPUT (N.O.) OPEN A active OPEN A not active
LED DL 15
OPEN B INPUT (N.O.) OPEN B active OPEN B not active
LED DL 16
STOP INPUT (N.C.) STOP non active STOP active or wiring error
LED DL 17
FSW CL INPUT (N.C.)
Closing safety
devices clear
Closing safety devices
triggered or wiring error
LED DL 18
FSW OP INPUT (N.C.)
Opening safety
devices clear
Opening safety devices
triggered or wiring error
9
LED DL 19 FCA1: OPEN
LIMIT SWITCH MOT1 (N.C.)
Limit switch
OFF or not used Limit Switch activated
LED DL 20 FCC1: CLOSE
LIMIT SWITCH MOT1 (N.C.)
Limit switch
OFF or not used Limit Switch activated
10
LED DL 21 FCA2: CLOSE
LIMIT SWITCH MOT2 (N.C.)
Limit switch
OFF or not used Limit Switch activated
LED DL 22 FCC2: CLOSE
LIMIT SWITCH MOT2 (N.C.)
Limit switch
OFF or not used Limit Switch activated
BOARD MALFUNCTION ERROR POSSIBLE CAUSES SOLUTIONS
There were two consecutive obstacle detections (the audio alarm also should sound) Remove obstructions
One of the motor driver components has failed The board needs to be repaired
24V accessory power missing The board needs to be repaired
The idle current in one of the motors is out of range Check the motors
Both limit switches are active at the same time Check the limit switches
Input voltage from the power supply is out of range Check DC input voltage
20