fantastic furniture Bridge User manual

Bridge
Ent Unit Large 2 Drawer

Recommended weight capacity: 80kgs

r
3

4

Top Panel (P1)
Bottom Panel (P2)
Right Panel (P3)
Left Panel (P4)
Middle Right Panel (P5)
Middle Left Panel (P6)
3x Support Rails (P7)
2x Shelves (P8)
2x Back Panels (P9)
Middle Back Panel (P10)
Right Door (P11)
Left Door (P12)
Drawer Front (P13)
2x Drawer Backs (P15)
2x Left Drawer Side (P16)
2x Right Drawer Side (P17)
2x Drawer Base (P18)
2x Drawer Support (P19)
2x Legs (P20)
Drawer Front (P14)
Hardware Pack
36 x Cam Bolts
(H1)
36 x Cam Nuts
(H2)
24 x Dowels
(H3) 4 x Hinges
(H5)
56 x Short Screws
(H6)
12 x Washers
(H7)
12 x Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
16 x Wedges
(H11)
2 x Middle Screws
(H12) 2 x Support Legs
(H13)
4 x Short Bolts
(H14)
4 x Washers
(H17)
2 x Wall Strap
(H18)
Right Panel
(P3)
Left Panel
(P4)
Middle Left Panel
(P6)
(P7)
Shelf
(P8)
Back Panel
(P9)
Right Door
(P11)
Middle Right Panel
(P5)
(P7)
(P7)
Shelf
(P8)
Back Panel
(P9)
Left Door
(P12)
(P15) (P17)
(P16)
(P18)
(P19)
6 x Long Dowels
(H4)
2 x Left Runner
Track
(H15-1)
12 x Long Screws
(H16)
2 x Right Runner
Track
(H -2)15
2 x Left
Runner
(H -3)15
2 x Right
Runner
(H -4)15
Legs
(P20)
Top Panel
(P1)
Bottom Panel
(P2)
Midd le
Back P anel
(P10 )
Drawer Front
(P13)
Drawer Front
(P14)
5

4 x Short Bolts
(H14)
1 x Allen Key
(H9)
2 x Support Legs
(H13)
9
12 x Washers
(H7)
12 x Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
H 8 P20
H 7
H 9
Using 4x Short Bolts (H14), secure 2x Support Legs (H13) to the Bottom Panel (P2) by tightening with the Allen Key (H9).
Use 12x Bolts (H8) and 12x Washers (H7) to secure 2x Legs (P20) to the underside of the Bottom Panel (P2).
Tighten with the Allen Key (H9).
Screw in 4x Levelling Feet (H10) to the bottom of the Legs (P20).
Ensure they are secure, and adjust accordingly if required.
Note: We strongly recommend assembling this entertainment unit on a soft
surface to minimise the risk of damaging the unit.
6

8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
(P2)
(P3)
(P4)
2 x Cam Bolts
(H1)
6 x Dowels
(H3)
Phillips Head
Screwdriver
(H3)
(H3)
(H1)
With assistance, carefully turn the Bottom Panel upright.
Insert 8x Dowels (H3) into the Bottom Panel (P2).
Secure 8x Cam Bolts (H1) to the Bottom Panel (P2), tightening with the Phillips Heads Screwdriver.
Insert 2x Dowels (H3) into the Right Panel (P3).
Insert 4x Dowels (H3) into the Left Panel (P4) and secure 2x Cam Bolts (H1) to the Left Panel (P4),
tightening with the Phillips Heads Screwdriver.
TWO PEOPLE
REQUIRED
7

(P6)
(P5)
(H4)
(H1)
(H4)
(H1)
6 x Cam Bolts
(H1)
2 x Dowels
(H3)
Phillips Head
Screwdriver
(P6) (H1)
6 x Long Dowels
(H4)
(H3)
(H4)
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver (P8)
(P7)
(P4)
(P6)
(H2)
Insert 2 x Long Dowels(H4) into Middle Right Panel(P5) as shown,
Insert 2 x Dowels(H3) into Middle Right Panel(P5) and secure 2 x Cam Bolts(H1) to Middle Right Panel(P5) as shown.
Insert 4 x Long Dowels(H4) into Middle Left Panel(P6) and secure 2 x Cam Bolts(H1) to Middle Left Panel(P6) by tightening with the
Phillips Head Screwdriver,turn over,then secure 2 x Cam Bolts(H1) to other side of Middle Left Panel(P6) by tightening with the Phillips
Head Screwdriver as shown.
Attach 1x Shelf (P8) and 1x Support Rail (P7) to the Left Side Panel (P4) and Middle Left Panel (P6) as shown.
Once in place, insert 4x Cam Nuts (H2) into the Shelf (P8) as shown. Rotate the Cam Nuts (H2) so the arrows point towards the incoming Cam
Bolts. Secure the Left Side Panel (P4) and the Middle Left Panel (P6) to the Shelf (P8) by tightening the Cam Nuts (H2) with the Phillips Head
Screwdriver.
TWO PEOPLE
REQUIRED
Ensure the grooves on the Left Side
Panel (P4) and the Middle Left Panel (P6)
are located at the back of the unit.
8

(P5)
Page 9
7
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver
8
Attach 1 x Shelf(P8) and 1 x Support(P7) to Middle Right Panel(P5) and Middle Left Panel(P6) as shown.
Insert 4 x Cam Nuts(H2) into Shelf(P8) as shown.
Rotate the Cam Nuts (H2) so the arrows point towards the incoming Cam Bolts. Secure the Middle Right Panel (P5) and
Middle Left Panel (P6) to the Shelf (P8) by tightening the Cam Nuts (H2) with the Phillips Head Screwdriver.
(P8)
(P7)
P4
P6
P5
6 x Cam Nuts
(H2)
Phillips Head
Screwdriver
TWO PEOPLE
REQUIRED
TWO PEOPLE
REQUIRED
Ensure the grooves on the Middle Right
Panel (P5) are located at the back of the unit.
(P6)
(H2)
Insert 6x Cam Nuts (H2) into the Left Panel (P4), Middle Left Panel (P6) and Middle Right Panel (P5) as shown. Rotate the Cam Nuts (H2) so
the arrows point towards the incoming Cam Bolts.
With assistance, attach the the Bottom Panel (P2) to the Left Panel (P4), Middle Left Panel (P6) and Middle Right Panel (P5) by tightening
the Cam Nuts (H2) with the Phillips Head Screwdriver.

Page 10
9
10
(P5)
(P6)
(P4)
(P3)
(P5)
(P6)
(P4)
Attach 1x Support Rail (P7) to the Right Panel (P3) and Middle Right Panel (P5).
Insert 2x Cam Nuts (H2) into the Right Panel (P3) as shown.
Rotate the Cam Nuts (H2) so the arrows point towards the incoming Cam Bolts.
Secure the Right Panel (P3) to the Bottom Panel (P2) by tightening the Cam Nuts (H2) with the Phillips Head Screwdriver.
(P7)
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
TWO PEOPLE
REQUIRED
With assistance, carefully turn the partially assembled unit upright.
TWO PEOPLE
REQUIRED
(H2)