fantastic furniture VENTURA User manual

Version 1.0
VENTURA
Gaming Chair

your Fantastic!
Looks like you’ve found
Caution:
Do not stand on, or use this chair as a step ladder.
Use this product for seating one person at a time.
This product should be checked perioically to ensure
all components are secure and all hardware is tight.
Recommended weight capacity: 120kg
We’re thrilled you’ve chosen Fantastic Furniture
to hdlp create a home you’ll love!
Love it ?Share it!
Fantas tic buy!Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Assembly checklist
Useful information
Read through the instructionscarefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.

to assemble the product
DO NOT USE
Seat (P10)
Seat Plate (P11)
Gas Lift (P13)
Star Base (P14)
Castors (P15)
Part list
What you need
Gas Lift Cover (P12)
Backrest (P1)
Left Arm (P8)
Right Arm (P9)
Allen Key
(H4)
8 x Long
Bolts (H1)
12 x Short
Bolts (H2)
6 x Small
Bolts (H3)
Headrest Pillow (P2)
Lumbar Pillow (P7)
Left Angle
Adjuster (P3)
Left Angle
Adjuster
Cover (P4)
Right Angle
Adjuster (P5)
Right Angle
Adjuster Cover (P6)
Backrest (P1) x 1;
Headrest Pillow (P2) x 1;
Left Angle Adjuster (P3) x 1;
Left Angle Adjuster Cover (P4) x 1;
Right Angle Adjuster (P5) x 1;
Right Angle Adjuster Cover (P6) x 1;
Lumbar Pillow (P7) x 1 ;
Left Arm (P8) x 1;
Right Arm (P9) x 1 ;
Seat (P10) x 1;
Seat Plate (P11) x 1;
Gas Lift Cover (P12) x 1;
Gas Lift (P13) x 1;
Star Base (P14) x 1;
Castors (P15) x 5;

Step 1
Insert 5 x Castors (P15) into the Star Base (P14) as shown.Push down firmly on each castor to ensure they
are fixed in position. Insert the Gas Lift (P13) into the top of Star Base (P14).Place the Gas Lift Cover (P12 )
over the top of the Gas Lift (P13) as shown.
Gas Lift (P13)
Star Base (P14)
Castors (P15)
Note the front facing orientation of the Seat Plate (P11) and align the holes on the Seat Plate (P11) with the
bottom of the Seat (P10) as shown. Secure the Seat Plate (P11) to the Seat (P10) with 4
x Short Bolts (H2) by
tightening with the Allen Key (H4).
Step 2
You will need
4 x Short
Bolts (H2)
Allen Key
(H4) Seat Plate
(P11)
Seat
(P10)
(H4)
Gas Lift Cover (P12)
(H2) (H2) (H2)
(H2)

Step 3
t
Step 4
t
Position the center hole of the Seat Plate (P11) over the top of Gas Lift (P13). Carefully lower the Seat
(P10) onto the Gas Lift (P13).Press seat down firmly. Check the connection is secure before sitting in the
chair.
You will need
8 x Long
Bolts(H1)
Allen Key
(H4)
Attach the Left & Right Arms (P8&P9) to each side of the Seat (P10) as shown with 8 x Long Bolts (H1) by
tightening with the Allen Key (H4). Ensure each arm is firmly secured.
(H1)
(H1)
(H1)
(H1)
(H4)
Left Arm (P8)
Seat (P10)
Right Arm (P9)
Seat Plate (P11) Gas Lift (P13)
(H1) (H1)
(H1) (H1)

7
Step 5
Attach Backrest (P1) to Seat (P10) by aligning the holes as shown and securing the Right Angle Adjuster
(P5) with 4 x Short Bolts (H2) by tightening with the Allen Key (H4).
Step 6
You will need
4 x Short
Bolts(H2)
Allen Key
(H4)
Backrest(P1)
Attach Backrest (P1) to Seat (P10) by aligning the holes as shown and securing the Left Angle Adjuster
(P3) with 4 x Short Bolts (H2) by tightening with the Allen Key (H4).
You will need
4 x Short
Bolts(H2)
Allen Key
(H4)
Backrest(P1)
(H2)
(H2) (H4)
Right Angle Adjuster(P5)
(H2)
(H2)
(H4)
Left Angle Adjuster(P3)
Seat(P10)
Seat(P10)
(H2)
(H2)
(H2)
(H2)

8
Step 7
Attach Right Angle Adjuster Cover (P6) to Right Angle Adjuster (P5) by aligning the holes and securing
with 4 x Small Bolts (H3) by tightening with the Allen Key (H4).
Step 8
You will need
4 x Small
Bolts (H3)
Allen Key
(H4)
Attach Left Angle Adjuster Cover (P4) to Left Angle Adjuster (P3) by aligning the holes and securing
with 2 x Small Bolts (H3) by tightening with the Allen Key (H4)
You will need
2 x Small
Bolts (H3)
Allen Key
(H4)
Backrest (P1)
(H3)
Right Angle Adjuster Cover (P6)
(H3)
Backrest (P1)
(H3)
(H3)
Left Angle Adjuster Cover (P4)
Seat (P10)
Seat (P10)
Right Angle Adjuster (P5)
Left Angle Adjuster (P3)
(H4)
(H4)
(H3)
(H3)

9
Step 9
Attach the Lumbar Pillow (P7) to the chair as shown by threading the longer end of the elastic bands on
the Lumbar Pillow (P7) between the bottom of the Backrest (P1) and Seat (P10), through to the back of the
chair. Then thread the shorter end of the elastic through the cut-outs at the top of the Backrest (P1) and
secure by clipping each end together at the back of the chair. Attach the Headrest Pillow (P2) to the chair
as shown by threading each end of the elastic band on the Headrest Pillow (P2) through the cut-outs at the
top of the Backrest (P1) and secure by clipping each end together at the back of the chair.
Job Complete!
Backrest (P1) Backrest (P1)
Lumbar Pillow (P7)
Headrest Pillow (P2)