fantastic furniture COMO User manual

Assembly Instructions
DRESSER 6 DRW
COMO
VER 1.1

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Divider
(P4)
Rail
(P5)
Rail
(P5)
Rail
(P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
2 x Back
Panel
(P9)
(Tools not provided)
Flat Blade Screwdriver
Phillips Head Screwdriver
Mallet
31 x Dowels
(H1)
6 x Long
Dowels
(H16)
36 x Long
Screws
(H2)
88 x Small
Screws
(H5)
6 x CL Runner
Tracks
(H6)
6 x CR Runner
Tracks
(H7)
13 x Cam Bolts
(H3)
13 x Cam Nuts
(H4)
30 x Small
Cam Nuts
(H11)
6 x DL Runners
(H8)
6 x DR Runners
(H9)
30 x Small
Cam Bolts
(H10)
Please make sure you have all these parts before you start.
Left
Drawer Side
(P12)
Drawer Front
(P10,P11)
×6
Right Drawer
Side (P13)
Drawer Back
(P15)
Drawer
Base(P14)
Support
Rail
(P16)
4 x Long
Screws
(H15)
6 x Plastic
Glides
(H17)
1 x Screw
(H13)
1 x Safety Strap
(H12)
2 x Washers
(H14)
1x Safety Strap Set

H5
H5
H5
H5
H5
H5
H5
H1 H1
H1
H1
H1
H1
H1
H3
H3
H5
H7
H7
H7
H5
Page 4
Step 1
You will need:
H5
H5
H6
H6
H6
H5
H5
H5
H5
H5
H5
H5
Step 2
You will need:
Step 3
You will need:
3 x CL Runner
Tracks
(H6)
3 x CR Runner
Tracks
(H7)
18 x
Dowels
(H1)
6 x
Cam Bolts
(H3)
9 x Small
Screws
(H5)
9 x Small
Screws
(H5)
(P2)
(P3)
(P3)
(P2)
Attach 3 x CL Runner Tracks (H6) to Left Side Panel (P2) with 9 x Small Screws (H5).
Attach 3 x CR Runner Tracks (H7) to Right Side Panel (P3) with 9 x Small Screws (H5).
Insert 18 x Dowels (H1) into Side Panels (P2) and (P3).
Attach 6 x Cam Bolts (H3) into Side Panels (P2) and (P3) as shown.
H1 H1
H1
H1
H1
H1
H1
H1
H1
H1
H3
H3
H3
H1
H3
H6
CL
H5
H7
CR
H5

Page 5
Step 6
You will need:
1 x Dowel
(H1)
1 x
Cam Bolt
(H3)
Step 4
You will need:
3 x CL Runner
Tracks
(H6)
9 x Small
Screws
(H5)
Step 5
You will need:
3 x CR Runner
Tracks
(H7)
9 x Small
Screws
(H5)
(P4)
(P4)
Insert 1 x Cam Nut (H4) into the hole of Rail (P6).
Rotate the cam nut so the arrows point towards the incoming cam bolt.
Insert 1 x Dowel (H1) into Rail (P6). Attach 1 x Cam Bolt (H3) into Rail (P6) as shown.
Attach 3 x Rails (P5) and Rail (P6) to Right Side Panel (P3),
then tighten the cam nuts.
Attach 3 x CL Runner Tracks (H6) to Divider (P4) with 9 x Small Screws (H5).
H5
H5
H6
H6
H5
H5
H5
H5
H5
H5
H5
(P5)
(P5)
(P5)
(P6)
(P3)
H4
H5
H5
H5
H5
H5
H5
H5
H5
H7
H7
H7
H5
H1
H3
1 x Cam Nut
(H4)
Turn Divider (P4) over to the other side, and then attach
3 x CR Runner Tracks (H7) with 9 x Small Screws (H5).
H6
CL
H5
H7
CR
H5
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

H4
H16
H16
H16
Page 6
Step 7
Step 8
Insert 1 x Cam Nut (H4) into the hole of Divider (P4).
Rotate the cam nut so the arrows point towards the incoming cam bolt.
Push Divider (P4) into place and tighten the cam nut.
Insert 6 x Long Dowels (H16) into 3 x Rails (P5) and Divider (P4).
You will need:
(P3)
(P4)
(P4)
(P6)
1 x Cam Nut
(H4)
(P5)
(P5)
(P5)
(P3)
You will need:
6 x Long Dowels
(H16)
Step 9
Insert 2 x Cam Nuts (H4) into the holes of Rails (P7) and (P8).
Rotate the cam nuts so the arrows point towards
the incoming cam bolts and tighten the cam nuts.
You will need:
2 x Cam Nuts
(H4)
(P4)
(P7)
(P8)
(P3)
H4
H4

(P1)
Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown.
You will need:
6 x Cam Bolts
(H3)
H3
H3
H3
H3
Step 11
Page 7
Step 10
You will need:
Insert 3 x Cam Nuts (H4) into the holes of Rails (P6,P7) and (P8).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Left Side Panel (P2) into place and tighten the cam nut.
Attach Rails (P7) and (P8) to Divider (P4) with 4 x Long Screws (H15).
Then hammer 6 x Plastic Glides (H17) on Side Panels (P2,P3) and Divider (P4).
3 x Cam Nuts
(H4)
(P6)
(P2)
(P3)
H4
H4
H4
H15 H15
H15
4 x Long
Screws
(H15)
H3
H3
6 x Plastic
Glides
(H17)
H17
H17
H17
H17
H17
H17
H17
20mm

H5
H5
6 x Dowels
(H1)
(P1)
(P2)
(P3)
H1
H1
Page 8
Step 12
You will need:
Insert 6 x Dowels (H1) into
Side Panels (P2,P3) and Divider (P4).
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2,P3) and Divider (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts.
CAREFULLY TURN
UNIT OVER
CAREFULLY LAY
UNIT ON FRONT
6 x Cam Nuts
(H4)
H1
H4
H4
H1
H4
Step 13
You will need:
28 x Small
Screws
(H5)
(P9)
(P9)
Put 2 x Back Panels (P9) into the groove on
the back of the chest ,screw them with
28 x Small Screws (H5). Holes are not pre-drilled so you need to
put some pressure with screwdriver to get started. Lift unit back up.

H10 H10
H11
H11
H11
H11
H11
1 x Dowel
(H1)
Page 9
Step 14
You will need:
5 x Small Cam
Bolts
(H10)
Step 15
Step 16
You will need:
(P10)
(P10)
(P10)
(P14)
(P12)
(P12)
(P13)
(P16)
(P13)
Insert 1 x Dowel (H1) into Drawer Front (P10).
Attach 5 x Small Cam Bolts (H10) as shown.
5 x Small Cam
Nuts
(H11)
Slide Drawer Base (P14) into the groove in Drawer Sides (P12,P13).
Insert 5 x Small Cam Nuts (H11) into the holes of
Drawer Sides (P12,P13) and Support Rail (P16).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Side (P12,P13) and Support Rail (P16) into place and tighten the cam nuts.
H10
H10
H10
H1
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

H2
H2 H2
Page 10
Step 17
You will need:
6 x Long Screws
(H2)
Step 18
You will need:
1 x DR Runner
(H9)
1 x DL Runner
(H8)
4 x Small
Screws
(H5)
Step 19
(P10)
(P14)
(P15)
(P12)
(P13)
H2
H2
H2
Attach 1 x DL Runner (H8) on the bottom of
Left Drawer Side (P12) and 1 x DR Runner (H9)
of Right Drawer Side (P13) with 4 x Small Screws (H5).
Repeat step13 to step17 to assemble other two drawers in the left side of dresser.
Replace Drawer Front (P10) with Drawer Front (P11) and repeat step13 to step 17
to assemble the three drawers in the right side of dresser.
Attach Drawer Back (P15) to Drawer Sides (P12,P13)
with 4 x Long Screws (H2), then attach Drawer Back (P15) to
Support Rail (P16) with 2 x Long Screws (H2).
Make sure that the groove lines up the whole way around the drawer.
(P13)
(P12)
H9
H8
H5
H5
H5
H9
H8
DR
DL
H5
H5
H5
H5