fantastic furniture HAVANA Tallboy 5 Drawer User manual

Version 1.0
HAVANA
Tallboy 5 Drawer
www.fantasticfurniture.com.au

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1)
Right Side
Panel
(P3)
Left Side
Panel
(P2)
Rail
(P5)
Back Panel
(P11)
30 x Cam
Bolts
(H3)
30 x Cam
Nuts
(H4)
Parts list
Box 1:Top Panel (P1);
Rail (P5); Rail (P6);
LF Leg (P7); RF Leg (P8);
LR Leg (P9); RR Leg (P10);
Box 2: Left Side Panel (P2);
Right Side Panel (P3);
2 x Rails (P4);
Back Panel (P11);
5 x Drawer Fronts (P12);
5 x Left Drawer Sides (P13);
5 x Right Drawer Sides (P14);
5 x Drawer Bases (P15);
5 x Drawer Backs (P16);
5 x Drawer Supports (P17);
Connect Stick (P18)
www.fantasticfurniture.com.au PAGE 4
52 x Small
Screws
(H5)
Rail
(P4) Rail
(P4)
25 x Small
Cam Nuts
(H11)
25 x Small
Cam Bolts
(H10)
Left
Drawer Side
(P13)
Right
Drawer Side
(P14)
Drawer Back
(P16)
Drawer
Base
(P15)
Drawer Front
(P12)
5 x CL Runner
Tracks
(H6)
4 x Plastic
Glides
(H17)
20 x Round
Head Bolts
(H14)
5 x CR Runner
Tracks
(H7)
10 x Handles
(H13)
5 x DR
Runners
(H9)
5 x DL
Runners
(H8)
LR
Leg
(P9)
RR Leg
(P10)
RF
Leg
(P8)
LF
Leg
(P7)
LF : Left Front LR : Left Rear
RF : Right Front RR : Right Rear
×5
Hardware pack
Rail
(P6)
4 x Wedges
(H15) 4 x Screws (H16)
Drawer
Support
(P17)
What you need
to assemble the product
Additional Tools Required
Flat head screwdriver;
Phillips head screwdriver;
Hammer
DO NOT USE
1 x Safety
Strap
(H18)
2 x Washers
(H20)
4 x Dowels
(H1) 29 x Small Dowels
(H2)
30 x Long
Screws (L25mm)
(H12)
1 x Screw
(L25mm)
(H19)

PAGE 5
(P3)
(P10)
(P8)
Insert 12 x Small Dowels (H2) into the holes of Side Panels (P2, P3).
Insert 16 x Cam Nuts (H4) into the holes of Side Panels (P2, P3).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P7, P9) to Left Side Panel (P2) and Legs (P8, P10) to Right Side Panel (P3).
Tighten the cam nuts using a Flat head screwdriver.
H4
(P2)
(P7)
(P9)
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H4
H2
H2
www.fantasticfurniture.com.au PAGE 5
Attach 16 x Cam Bolts (H3) into Legs (P7, P8, P9, P10).
You will need
Step 1
You will need
Step 2
16 x Cam Bolts
(H3) Phillips head
screwdriver
16 x Cam Nuts
(H4)
Flat head
screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
(P7)
(P9)
(P10)
(P8)
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
12 x Small
Dowels (H2)

(P3)
www.fantasticfurniture.com.au PAGE 6
Attach 8 x Cam Bolts (H3) into Side Panels (P2, P3) and Legs (P7, P8, P9, P10).
Attach 5 x CL Runner Tracks (H6) to Left Side Panel (P2) with 15 x Small Screws (H5).
Attach 5 x CR Runner Tracks (H7) to Right Side Panel (P3) with 15 x Small Screws (H5).
H7
CR
H5
Step 5
You will need
8 x Cam Bolts
(H3) Phillips head screwdriver
5 x CL Runner
Track (H6)
You will need
Step 3
15 x Small
Screws (H5)
Phillips head
screwdriver
You will need
Step 4
15 x Small
Screws (H5)
Phillips head
screwdriver
5 x CR Runner
Track (H7)
H6
CL
H5
H6
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5 H5 H5
H7
(P3)
(P10)
(P10)
(P8)
(P8)
H5 H5 H5
H5 H5 H5
H5 H5 H5
H5 H5
H5
(P2)
(P2)
(P7)
(P9)
(P7) (P9)
H3
H3 H3
H3 H3
H3
H3
H3
H6
H6
H6
H6
H7
H7
H7
H7

www.fantasticfurniture.com.au PAGE 7
Insert 4 x Small Dowels (H2) into Left Side Panel (P2) and Legs (P7, P9).
Insert 4 x Cam Nuts (H4) into the holes of Rails (P4, P5, P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Rails (P4, P5, P6) to the left frame, then tighten the cam nuts using a Flat head screwdriver.
Insert 4 x Small Dowels (H2) into Right Side Panel (P3) and Leg (P10).
Insert 4 x Cam Nuts (H4) into the holes of Rails (P4, P5, P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push the right frame into place, then tighten the cam nuts using a Flat head screwdriver.
Hammer 4 x Plastic Glides (H2) on Legs (P7, P8, P9, P10) as shown.
4 x Cam Nuts
(H4)
Flat head
screwdriver
You will need
Step 6
4 x Cam Nuts
(H4)
You will need
Flat head
screwdriver
Step 7
4 x Plastic
Glides (H2)
Hammer
(P3)
(P10)
(P8)
(P2)
(P7)
(P9)
(P6)
(P4)
(P4)
(P5)
(P6)
(P4)
(P4)
(P5)
H4
Back Panel Slot
H4
H4
H4
H2
H2 H2
H2
H2
H2
H2
H4
H4
H4
H4
H2
H2
H2
H2
H2
4 x Small
Dowels (H2)
4 x Small
Dowels (H2)

www.fantasticfurniture.com.au PAGE 8
Insert 4 x Small Dowels (H2) into Side Panels (P2, P3) as shown.
Carefully turn the tallboy over to an upright position.
Slide Back Panels (P11) into the grooves in Legs (P9, P10) and Rail (P6).
Insert 4 x Dowels (H1) into Legs (P7, P8, P9, P10) as shown.
You will need
Step 9
You will need
Step 8
(P3)
H2 H2
H2 H2
(P2)
(P9)
(P7)
(P6)
(P8)
(P10)
(P11)
H1
H1
H1
H1
4 x Dowels
(H1)
4 x Small
Dowels (H2)
make sure the arrow label
is facing top when slide
in the back panel

Attach 6 x Cam Bolts (H3) into Top Panel (P1) as shown.
6 x Cam Bolts
(H3) Phillips head
screwdriver
You will need
6 x Cam Nuts
(H4)
You will need
Step 11
Flat head
screwdriver
www.fantasticfurniture.com.au PAGE 9
Insert 6 x Cam Nuts (H4) into the holes of Side Panels (P2, P3) and Legs (P7, P8, P9, P10).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) into place, and then tighten the cam nuts.
Step 10
(P1)
H3
H3 H3
H3
H3
H3
H4
H4
(P9)
(P7)
(P1)
(P2)
(P8)
H4
H4
H4

Phillips head
screwdriver
(P12)
H10
H10
H10
H10
H10
Screw 5 x Small Cam Bolts (H10) into Drawer Front (P12) with a Phillips head screwdriver.
Phillips head
screwdriver
5 x Small Cam
Bolts (H10)
You will need
Step 13
2 x Small
Screws (H5)
www.fantasticfurniture.com.au PAGE 10
You will need
Step 12
4 x Wedges
(H15) 4 x Screws (H16)
Make sure Wedge (H15) is facing
to the bottom of Top Panel (P1).
Secure Back Panel (P11) in place with 4 x Wedges (H15) using 4 x Screws (H16).
Use 2 x Small Screws (H5) to fix Back Panel (P11) onto Rail (P4).
Tighten the screws with a Phillips head screwdriver.
(P11)
(P4)
H15
H16
H5
H5 H5